molecalculator

Moles & Molar Mass

Absorbance Equation: Units & How to Use It

Calculator No. 01-10374 · Updated · Formula and assumptions shown below

Absorbance (AU) 1.500
Transmittance
3.162 %
= 100 × 10^(-Absorbance (AU))
Molar absorptivity (ε)
15000 L·mol⁻¹·cm⁻¹
Set in the form below
Concentration
0.0001 mol/L
Set in the form below
You enter
Molar absorptivity (ε) (L·mol⁻¹·cm⁻¹), Concentration (mol/L), Path length (cm)
You get
Absorbance (AU), Transmittance (%)
Rounding
3 dp · 1 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The absorbance equation, A = εcl, expresses how much light a sample absorbs, and its standard unit is the dimensionless absorbance unit (AU), often just called “absorbance.” You enter the molar absorptivity (ε, in L·mol⁻¹·cm⁻¹), the path length (l, in cm), and the concentration (c, in mol/L) to get a value that typically ranges from 0 to 2 for reliable measurements. This page explains each term, the units involved, and how to avoid the most common mistakes when using Beer-Lambert law calculations.

Formula

The Beer-Lambert law is written as:

A = ε · c · l

  • A = absorbance (no unit, but often reported as AU or “absorbance units”)
  • ε (epsilon) = molar absorptivity or molar extinction coefficient (L·mol⁻¹·cm⁻¹)
  • c = concentration of the absorbing species (mol/L, i.e., M)
  • l = path length of the cuvette (cm)

The equation is linear: if you double the concentration, absorbance doubles, provided ε and l are constant. The unit of ε is chosen so that A comes out dimensionless. Because ε is usually given in L·mol⁻¹·cm⁻¹ and l in cm, the product ε·c·l has units of (L·mol⁻¹·cm⁻¹) × (mol/L) × (cm) = 1, which cancels cleanly.

Worked Example

Using the default values from the calculator: ε = 15000 L·mol⁻¹·cm⁻¹, c = 0.0001 mol/L (1.0 × 10⁻⁴ M), l = 1 cm.

Plug into the equation:

A = 15000 × 0.0001 × 1 = 1.500

So the absorbance is 1.500 AU. The transmittance is then T = 10⁻¹·⁵ = 0.0316, or 3.16% (the calculator shows 3.2% when rounded to one decimal). This means the sample transmits only about 3% of the incident light – a fairly concentrated or strongly absorbing sample.

Assumptions

  • The solution is dilute enough that molecules do not interact with each other (no aggregation or self-absorption).
  • The light is monochromatic (single wavelength).
  • The absorbing species is the only one that absorbs at that wavelength.
  • The path length is uniform and the cuvette windows are clean and parallel.
  • The solvent does not absorb significantly at the chosen wavelength (or a blank is used to correct for it).

Why Absorbance Has No Unit (But People Say “AU”)

Absorbance is defined as the logarithm of the ratio of incident light intensity (I₀) to transmitted light intensity (I): A = log₁₀(I₀/I). Since both intensities are in the same unit (e.g., W/m²), the ratio is unitless, and the logarithm of a unitless number is also unitless. However, in practice, spectrophotometers report a number that is often labeled “AU” (absorbance units) to remind you that it is an absorbance reading, not a concentration or a percentage. The AU is not a physical unit like meters or grams; it is a convention. When you see “A = 0.5 AU,” it simply means the logarithm of the intensity ratio is 0.5.

How to Choose the Right Wavelength and Cuvette

To get a reliable absorbance reading, you need to pick a wavelength where the sample absorbs strongly (usually the λmax, the wavelength of maximum absorption). This gives the highest sensitivity and the best signal-to-noise ratio. The path length is typically 1 cm for standard cuvettes, but you can use longer or shorter paths (e.g., 0.1 cm for very concentrated samples) to keep the absorbance in the ideal range.

  • For quantitative analysis, aim for absorbance between 0.1 and 1.0 (some say up to 1.5). Below 0.1, the signal is small relative to noise; above 1.5, the detector may not be linear, and stray light becomes a problem.
  • If your sample is too concentrated, dilute it (but remember to account for the dilution factor in your final concentration).
  • If the absorbance is too low, use a longer path length or concentrate the sample.

Common Units Mistakes and How to Avoid Them

The most frequent error is mixing up concentration units. The Beer-Lambert law requires molarity (mol/L). If you have a concentration in mg/mL, you must convert to mol/L using the molar mass. For example, a 5 mg/mL solution of a compound with molar mass 250 g/mol is (0.005 g/mL) / (250 g/mol) = 2.0 × 10⁻⁵ mol/mL = 0.020 mol/L (since 1 mL = 0.001 L, so 2.0×10⁻⁵ mol/0.001 L = 0.02 M).

Another common mistake is using the wrong units for ε. If ε is given in M⁻¹·cm⁻¹ (which is the same as L·mol⁻¹·cm⁻¹), then c must be in mol/L and l in cm. Sometimes ε is given in cm²/mol (rare), which would require different units for concentration. Always check the units on your ε value.

Also, be careful with path length: if you use a 0.5 cm cuvette, you must enter 0.5, not 1. Forgetting this will give an absorbance that is twice the correct value.

Reading the Result: Absorbance vs. Transmittance

Many instruments display transmittance (%) instead of absorbance. The relationship is A = 2 – log₁₀(%T). For example, if %T = 10%, then A = 2 – 1 = 1.0. Conversely, if A = 2, then %T = 10⁻² = 1%. Absorbance is preferred for quantitative work because it is directly proportional to concentration, while transmittance is exponential. When you read a result, always note whether it is absorbance or transmittance – a common mistake is treating %T as if it were absorbance.

Limitations of the Beer-Lambert Law

The linear relationship between absorbance and concentration breaks down at high concentrations (typically above 0.01 M for many compounds) due to molecular interactions, changes in refractive index, and scattering. Also, if the solution is turbid or contains particles, scattering adds to the apparent absorbance. The law also assumes the light is monochromatic; if you use a wide bandwidth, the linearity suffers. For these reasons, always verify linearity with a calibration curve and stay within the concentration range where the law holds.

Frequently Asked Questions

What is the unit of molar absorptivity (ε)?

Molar absorptivity is expressed in L·mol⁻¹·cm⁻¹ (also written as M⁻¹·cm⁻¹). It is a measure of how strongly a substance absorbs light at a particular wavelength. The value depends on the compound and the solvent, and it is usually determined experimentally. For example, a compound with ε = 15000 L·mol⁻¹·cm⁻¹ absorbs strongly.

Can absorbance be greater than 1?

Yes, absorbance can be greater than 1, but for quantitative work it is often unreliable. An absorbance of 2 corresponds to 1% transmittance, and an absorbance of 3 corresponds to 0.1% transmittance. Most spectrophotometers become inaccurate above about 2.5 due to stray light and detector limitations. If you get an absorbance above 2, dilute your sample and multiply the result by the dilution factor.

Why is the path length usually 1 cm?

The 1 cm path length is a standard because it is convenient and gives a good balance between sensitivity and sample volume. Most standard cuvettes have a 1 cm internal width. Using a different path length is fine, but you must enter the correct value in the equation. The path length is part of the product ε·c·l, so a longer path gives a higher absorbance for the same concentration.

What is the difference between absorbance and optical density (OD)?

In most contexts, they are the same. Optical density (OD) is an older term for absorbance, often used in microbiology and biochemistry. Both refer to the logarithm of the ratio of incident to transmitted light. However, in some fields, OD may be measured at a specific wavelength without a blank correction, while absorbance is usually corrected for the solvent blank. For practical purposes, you can treat them as equivalent.

How do I convert absorbance to concentration?

Rearrange the equation to solve for concentration: c = A / (ε·l). For example, if A = 0.600, ε = 15000 L·mol⁻¹·cm⁻¹, and l = 1 cm, then c = 0.600 / (15000 × 1) = 4.0 × 10⁻⁵ mol/L (40 µM). This is the basis of many quantitative assays. Always use the molar absorptivity at the same wavelength and in the same solvent as your measurement.

Remember to follow your lab method, the safety data sheet (SDS) and your supervisor when performing actual measurements.

Related

Formula used
in m | Molar absorptivity (ε) | L·mol⁻¹·cm⁻¹ | 15000 | 0
in c | Concentration | mol/L | 0.0001 | 0
in l | Path length | cm | 1 | 0
out a | Absorbance (AU) | - | m * c * l | 3
out t | Transmittance | % | 100 * 10^(-a) | 1

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →