molecalculator

Moles & Molar Mass

CO₂ Air Density: Formula, Values, and Comparison

Calculator No. 01-3043 · Updated · Formula and assumptions shown below

CO₂ density 1.830 kg/m³
Dry-air density at same conditions
1.204 kg/m³
Result, rounded to 3 decimal places
CO₂-to-air density ratio
1.519
= CO₂ density ÷ Dry-air density at same conditions
Absolute pressure
101.325 kPa
Set in the form below
You enter
Absolute pressure (kPa), Temperature (°C), CO₂ molar mass (g/mol)
You get
CO₂ density (kg/m³), Dry-air density at same conditions (kg/m³), CO₂-to-air density ratio
Rounding
3 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

At 20 °C and 101.325 kPa, pure carbon dioxide (CO₂) has a density of about 1.83 kg/m³, compared with about 1.20 kg/m³ for dry air at the same conditions. CO₂ density is not one fixed number: it depends chiefly on temperature and pressure, so the figures below are reference values rather than universal constants.

Formula

The calculator uses the ideal-gas density equation, ρ = PM/(RT). In the input form, pressure is entered in kilopascals, temperature in degrees Celsius, and molar mass in grams per mole. The expression converts pressure to pascals by multiplying by 1,000, molar mass to kilograms per mole by dividing by 1,000, and temperature to kelvins by adding 273.15. It then uses R = 8.31446261815324 J/(mol·K).

  • ρ is gas density in kg/m³.
  • P is absolute pressure in pascals; gauge pressure alone is not suitable.
  • M is molar mass in kg/mol. The default CO₂ value, 44.01 g/mol, is based on standard atomic weights for carbon and oxygen.
  • R is the molar gas constant in J/(mol·K).
  • T is absolute temperature in kelvins, equal to °C + 273.15.

The comparison uses dry air’s conventional mean molar mass of 28.96546 g/mol, treated as an input constant in the expression. The ratio is the calculated CO₂ density divided by calculated dry-air density under identical pressure and temperature.

Worked Example

Using the exact defaults from the calculator: P = 101.325 kPa, t = 20 °C, and M = 44.01 g/mol.

  1. Convert pressure: 101.325 × 1,000 = 101,325 Pa.
  2. Convert temperature: 20 + 273.15 = 293.15 K.
  3. Convert molar mass: 44.01 / 1,000 = 0.04401 kg/mol.
  4. Calculate CO₂ density: ρ = (101,325 × 0.04401) / (8.31446261815324 × 293.15) = 1.829 kg/m³, rounded to three decimal places.
  5. At the same conditions, dry air is about 1.204 kg/m³ using 28.96546 g/mol; the density ratio is about 1.519.

Assumptions

  • The gases are treated as ideal, a good approximation for many everyday conditions but less reliable at high pressures or near condensation.
  • The comparison is for dry air and pure CO₂ at the same absolute pressure and temperature.
  • The stated molar masses are conventional values; actual air composition varies slightly.

Why CO₂ Is Denser Than Air

At equal temperature and pressure, ideal-gas density is proportional to molar mass. A CO₂ molecule has a molar mass of about 44.01 g/mol, while average dry air is about 28.97 g/mol. Their ratio, 44.01/28.96546, is about 1.519. This is why CO₂ is roughly 52% denser than dry air under matching conditions.

“Heavier than air” describes a comparison of gas densities, not a guarantee that CO₂ will stay in a motionless layer at floor level. Gas movement, temperature differences, ventilation, room shape, and mixing all matter. Diffusion and air currents mix gases; a room cannot be assessed for safety simply by assuming that CO₂ collects only near the floor.

How Temperature and Pressure Change Density

For a fixed gas composition, the ideal-gas equation predicts that density rises in proportion to absolute pressure and falls as absolute temperature rises. For example, at the same pressure, warming a gas from 20 °C to 40 °C reduces its ideal-gas density by the factor 293.15/313.15. Raising absolute pressure, by contrast, increases density in direct proportion in this model.

Use absolute pressure, which is measured relative to a vacuum. At sea level, atmospheric pressure is approximately 101.325 kPa; local weather and elevation change it. A gauge reading reports pressure relative to surrounding atmosphere, so it must be combined with local atmospheric pressure before using this formula. If pressure is entered in bar or atmospheres, convert it to kPa first: 1 bar = 100 kPa, and 1 atm = 101.325 kPa.

Values at Common Conditions

Approximate ideal-gas values for pure CO₂ illustrate why temperature and pressure should always accompany a density figure:

  • At 0 °C and 101.325 kPa: about 1.977 kg/m³.
  • At 20 °C and 101.325 kPa: about 1.829 kg/m³.
  • At 25 °C and 101.325 kPa: about 1.799 kg/m³.

These are calculated from the ideal-gas equation, not fixed properties independent of conditions. They also assume the gas is pure CO₂. In a mixture, density depends on the mixture’s overall average molar mass and its temperature and pressure; the pure-CO₂ result does not directly give the density of room air containing some CO₂.

Common Misconceptions and Limits

A common confusion is between gas density and the density of liquid or solid carbon dioxide. The calculator applies to a gas. Liquid CO₂ has a much higher density and exists only under appropriate pressure and temperature conditions; dry ice is solid CO₂. Neither should be described using the gas result.

The ideal-gas equation is useful for ordinary calculations, but real gases can depart from it, especially at high pressure or near a phase change. For precision work in those conditions, use a suitable real-gas equation of state or a trusted property table for the exact temperature, pressure, and composition. Rounding also matters: the displayed result is rounded to three decimal places, while intermediate calculations use the entered values.

Safety and Practical Context

CO₂ is colorless and odorless, so smell cannot warn you of a hazardous concentration. It can displace oxygen, and elevated concentrations can cause serious health effects. A density comparison does not indicate whether a space is safe, nor does it predict concentration distribution reliably. Follow applicable workplace or confined-space requirements, use appropriate monitoring and ventilation, and do not enter a potentially hazardous atmosphere based on assumptions about where CO₂ settles.

Frequently Asked Questions

Is CO₂ heavier than air?
Yes. At the same temperature and pressure, pure CO₂ is about 1.52 times as dense as dry air, based on their molar masses.

What is the density of CO₂ at room temperature?
At 20 °C and standard atmospheric pressure of 101.325 kPa, it is approximately 1.829 kg/m³. At 25 °C under the same pressure, it is approximately 1.799 kg/m³.

Does CO₂ always sink to the floor?
No. Although pure CO₂ is denser than air at equal conditions, currents, diffusion, heat, ventilation, and obstacles mix gases. Density alone cannot predict where a hazardous concentration will occur.

How do I calculate CO₂ density?
Use ρ = PM/(RT), with absolute pressure in pascals, molar mass in kg/mol, temperature in kelvins, and R = 8.31446261815324 J/(mol·K). Convert units before substituting.

Is the density of CO₂ the same as its molar mass?
No. Molar mass is mass per mole, usually expressed in g/mol; density is mass per volume, such as kg/m³. Temperature and pressure connect them through the gas equation.

Related

Formula used
in p | Absolute pressure | kPa | 101.325 | 0
in t | Temperature | °C | 20 | -273.15
in mm | CO₂ molar mass | g/mol | 44.01 | 0.001
out d | CO₂ density | kg/m³ | (p * 1000) * (mm / 1000) / (8.31446261815324 * (t + 273.15)) | 3
out da | Dry-air density at same conditions | kg/m³ | (p * 1000) * (28.96546 / 1000) / (8.31446261815324 * (t + 273.15)) | 3
out r | CO₂-to-air density ratio | - | d / da | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →