molecalculator

Moles & Molar Mass

C1V1 C2V2 Equation: Dilution Formula Explained

Calculator No. 01-9279 · Updated · Formula and assumptions shown below

Volume of stock needed (V1) 10.00 mL
Final volume (V2)
40.00 mL
= Initial concentration (C1) × Initial volume (V1) ÷ Final concentration (C2)
Initial concentration (C1)
1 M
Set in the form below
Initial volume (V1)
10 mL
Set in the form below
You enter
Initial concentration (C1) (M), Initial volume (V1) (mL), Final concentration (C2) (M), Final volume (V2) (mL)
You get
Volume of stock needed (V1) (mL), Final volume (V2) (mL)
Rounding
2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The C1V1 = C2V2 equation is a simple formula used to calculate how to dilute a stock solution to a desired concentration. You enter the initial concentration (C1), the initial volume (V1), and either the final concentration (C2) or final volume (V2) to find the missing value. This calculator solves for any of the four variables in the dilution equation.

Formula

The dilution equation is written as:

C1 × V1 = C2 × V2

Where:

  • C1 = initial concentration (mol/L or M, but any concentration unit works as long as it is consistent)
  • V1 = initial volume (mL, L, or any volume unit, as long as it is consistent)
  • C2 = final concentration (same unit as C1)
  • V2 = final volume (same unit as V1)

The equation is a rearranged form of the principle that the amount of solute (in moles) remains constant during dilution. Since moles = concentration × volume, and the moles of solute do not change when you add solvent, C1V1 (initial moles) equals C2V2 (final moles).

Worked Example

Using the default values from the calculator above:

Suppose you have a 1.0 M stock solution and you want to prepare 40 mL of a 0.25 M solution. What volume of stock do you need?

Using the formula C1V1 = C2V2:

1.0 M × V1 = 0.25 M × 40 mL

V1 = (0.25 × 40) / 1.0 = 10 mL

So you need 10 mL of the 1.0 M stock, then add solvent to reach a final volume of 40 mL. The calculator gives the same result: V1 = 10.00 mL.

If instead you know you have 10 mL of stock and want a final concentration of 0.25 M, you can solve for V2:

1.0 M × 10 mL = 0.25 M × V2

V2 = (1.0 × 10) / 0.25 = 40 mL

The calculator gives V2 = 40.00 mL.

Assumptions

  • The amount of solute (moles) stays constant – you are only adding solvent.
  • The solutions are ideal and volumes are additive (true for most dilute aqueous solutions).
  • Concentration units are consistent on both sides of the equation.
  • Volume units are consistent on both sides (you can mix mL and L only if you convert first).

How to Use the C1V1 = C2V2 Equation

The equation is most often used to prepare a dilute solution from a concentrated stock. The typical steps are:

  1. Identify which three variables you know (C1, V1, C2, V2).
  2. Rearrange the equation to solve for the unknown. For example, to find V1: V1 = (C2 × V2) / C1.
  3. Plug in the numbers and calculate.
  4. Measure the calculated volume of stock solution and transfer it to a volumetric flask or graduated cylinder.
  5. Add solvent (usually water or buffer) until the total volume reaches V2, not just add V2 minus V1 of solvent – the final volume must be V2.

Common Mistakes and Misconceptions

  • Mixing units: If C1 is in mM and C2 in M, you must convert to the same unit. Similarly, V1 in mL and V2 in L will give a wrong answer.
  • Adding solvent to a volume: The most common error is adding (V2 – V1) of solvent to the stock, but this only works if volumes are perfectly additive, which is not always true. Always bring the final volume up to V2 with solvent, not just add a fixed amount.
  • Forgetting that V2 is final total volume: V2 includes the stock volume plus the solvent added. For example, if you need 100 mL final volume, you add stock and then solvent to reach 100 mL, not add 100 mL of solvent.
  • Using the equation for non-dilution problems: C1V1 = C2V2 only applies when the amount of solute is constant. It does not apply to reactions where solute is consumed or produced.

When to Use C1V1 = C2V2 vs. Other Dilution Methods

The C1V1 = C2V2 equation is the go-to method for simple dilutions. However, there are other approaches:

  • Serial dilutions: When you need a series of dilutions (e.g., 1:10, 1:100, 1:1000), you can either use C1V1 = C2V2 for each step or use a dilution factor. The equation still applies to each step, but you must track the concentration after each dilution.
  • Dilution factor method: If you know the dilution factor (e.g., 1:10), you can calculate final concentration by dividing the initial concentration by the factor. This is a shortcut that works for simple ratios.
  • Percent solutions: For percent concentrations (w/v or v/v), the same principle applies but you must be careful with units (e.g., % w/v is grams per 100 mL).

For most lab dilutions, C1V1 = C2V2 is the most direct and flexible method.

Limitations and Important Notes

The equation assumes that the amount of solute is constant, which is true for dilutions. However, it does not account for:

  • Non-ideal behavior: At very high concentrations, the volume may not be perfectly additive due to molecular interactions. For most lab work, this is negligible.
  • Temperature changes: Concentration is temperature-dependent because volume changes with temperature. For precise work, control temperature or use mass-based concentrations.
  • Chemical reactions: If the solute reacts with the solvent or another component, the equation is invalid.

Always follow your lab method, the safety data sheet (SDS) and your supervisor when preparing solutions.

Frequently Asked Questions

What does C1V1 = C2V2 stand for?

C1 is the concentration of the stock solution, V1 is the volume of stock you take, C2 is the final concentration you want, and V2 is the final total volume of the diluted solution. The equation simply states that the amount of solute (concentration × volume) is the same before and after dilution.

How do I solve for V1?

Rearrange the equation to V1 = (C2 × V2) / C1. For example, if you want 100 mL of 0.1 M solution from a 1 M stock, V1 = (0.1 × 100) / 1 = 10 mL.

Can I use different units for C1 and C2?

No, the units must be the same on both sides. If C1 is in mM and C2 in M, convert mM to M (divide by 1000) before plugging in. The same applies to volumes – you can use mL on both sides, but not mL on one side and L on the other.

What is the difference between C1V1 = C2V2 and M1V1 = M2V2?

They are the same equation. M stands for molarity (mol/L), which is a common concentration unit, but the equation works with any concentration unit as long as it is consistent. Some textbooks use M1V1 = M2V2, but the principle is identical.

Why do I need to bring the final volume up to V2 instead of adding V2 – V1 of solvent?

Because volumes are not always perfectly additive. When you mix a solute with a solvent, the final volume may be slightly different from the sum of the individual volumes. By adding solvent to a final total volume of V2, you ensure the concentration is exactly C2. This is especially important when preparing solutions in volumetric flasks.

Does C1V1 = C2V2 work for serial dilutions?

Yes, you can apply the equation to each step of a serial dilution. For example, to make a 1:10 dilution, you use C1V1 = C2V2 with V2 = 10 mL and V1 = 1 mL, giving C2 = C1/10. Then the next step uses the new concentration as C1.

Related

Formula used
in c1 | Initial concentration (C1) | M | 1.0 | 0
in v1 | Initial volume (V1) | mL | 10 | 0
in c2 | Final concentration (C2) | M | 0.25 | 0
in v2 | Final volume (V2) | mL | 40 | 0
out v1_needed | Volume of stock needed (V1) | mL | c2 * v2 / c1 | 2
out v2_final | Final volume (V2) | mL | c1 * v1 / c2 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →