The C1V1 = C2V2 formula works exactly the same whether your concentrations are in percent (%), molarity (mol/L), or any other unit, as long as you use the same unit on both sides. To dilute a stock solution with a percentage concentration, plug the percentages and volumes into the equation and solve for the unknown; the result is a volume, not a percentage.
Formula
The dilution equation is written as:
C1 × V1 = C2 × V2
Where:
- C1 = concentration of the stock (starting) solution, in % (w/v), % (v/v), mol/L, or any consistent unit.
- V1 = volume of the stock solution you take, in mL or L.
- C2 = final concentration after dilution, in the same unit as C1.
- V2 = final total volume after dilution (stock + diluent), in the same unit as V1.
The calculator above solves for V2 when you enter C1, V1, and C2. It also shows the mass of solute in the stock portion, using the definition of percent (w/v): % = (grams of solute / 100 mL of solution).
Worked Example
Suppose you have a 10% (w/v) stock solution of a reagent and you need 100 mL of a 2% solution. Using the defaults:
- Write the equation: 10% × V1 = 2% × 100 mL
- Solve for V1: V1 = (2 × 100) / 10 = 20 mL
- So you take 20 mL of the 10% stock and add solvent (usually water) to a final volume of 100 mL.
The calculator gives V2 = 10 × 100 / 2 = 500 mL, which is the final volume if you start with 100 mL of stock and want a 2% solution. Both are correct uses of the formula—just be clear which volume you are solving for.
Assumptions
- Percent concentrations are based on the same basis (w/v, v/v, or w/w) on both sides.
- Volumes are additive (dilute solutions, not concentrated acids or alcohols where mixing volumes shrink).
- The final volume is the total volume after adding diluent, not the volume of solvent added.
- Temperature is constant (density changes with temperature affect w/v percentages).
How Percent Concentrations Work
Percent can mean different things in chemistry, and you must know which one you are using:
- % w/v (weight/volume): grams of solute per 100 mL of solution. Example: 10% w/v NaCl = 10 g NaCl in 100 mL final solution.
- % v/v (volume/volume): mL of solute per 100 mL of solution. Example: 70% v/v ethanol = 70 mL ethanol in 100 mL final solution.
- % w/w (weight/weight): grams of solute per 100 g of solution. Example: 37% w/w HCl = 37 g HCl per 100 g of acid solution.
The C1V1 formula works for all three, but you cannot mix different bases. If C1 is % w/v and C2 is % v/v, the equation gives a meaningless number.
When to Use C1V1 for Percentages
Use this formula whenever you need to dilute a stock solution of known percentage to a lower percentage. Common lab tasks include:
- Making a working solution from a concentrated reagent (e.g., diluting 10% SDS to 0.1% SDS).
- Preparing a series of standards from a stock solution.
- Adjusting the concentration of a buffer or dye solution.
The formula is also used in industry and teaching labs for simple dilutions. It does not require knowing molar mass or density, which is why percent-based dilutions are quick.
Common Mistakes and How to Avoid Them
- Mixing different percent bases: Always check whether your stock is w/v, v/v, or w/w. If you have a w/w stock (like concentrated HCl), you need density to convert to w/v before using the formula.
- Adding solvent volume instead of final volume: The formula uses V2 as the final total volume. If you need 100 mL of final solution, you add solvent to reach 100 mL, not add 100 mL of solvent to the stock.
- Unit mismatch: Use the same volume unit on both sides (mL or L). If V1 is in mL and V2 in L, convert first.
- Rounding too early: Keep extra digits in intermediate steps, then round at the end.
Limitations of the Formula
C1V1 = C2V2 assumes that the amount of solute is conserved during dilution. This is true for most aqueous solutions, but fails when:
- Solutes react with the diluent (e.g., hydrolysis).
- Volumes are not additive (concentrated acids, alcohols, or high concentrations).
- Temperature changes cause density shifts, altering w/v percentages.
- The solution is saturated—diluting a saturated stock may cause precipitation if the final concentration is below the solubility limit? Actually, the formula still works for the amount of solute, but you must ensure the stock is homogeneous.
For precise work, always prepare by mass when using w/w percentages, and use volumetric flasks for w/v solutions.
Frequently Asked Questions
Can I use C1V1 = C2V2 with percent concentrations directly?
Yes, as long as both concentrations are in the same percent basis (both w/v, both v/v, or both w/w). The percentages cancel out in the calculation, so you can plug them in as numbers (e.g., 10 and 2) without converting to decimals.
What if my stock is % w/w and I want % w/v?
You cannot use the formula directly. You need to convert the w/w concentration to w/v using the density of the solution: % w/v = (% w/w) × density (g/mL). For example, 37% w/w HCl has a density of about 1.19 g/mL, so it is approximately 44% w/v.
Does the formula work for v/v dilutions like ethanol?
Yes, for dilute ethanol solutions, volumes are nearly additive. For high concentrations (e.g., 95% to 70%), mixing ethanol and water causes volume contraction, so the final volume is less than the sum. Use the formula with caution; better to measure by mass or use a volumetric flask.
How do I make 100 mL of a 1% solution from a 5% stock?
Using C1V1 = C2V2: 5 × V1 = 1 × 100, so V1 = 20 mL. Take 20 mL of the 5% stock and add solvent to a final volume of 100 mL.
What is the difference between % w/v and % v/v?
% w/v is grams of solute per 100 mL of solution (common for solids dissolved in liquid). % v/v is mL of solute per 100 mL of solution (used for liquid-liquid mixtures like ethanol in water). They are not interchangeable.
Can I use the formula to concentrate a solution?
No, the formula is for dilution (adding solvent). To concentrate, you would need to remove solvent, which changes the amount of solute if not done carefully. The equation assumes solute mass is constant, but evaporation removes solvent only if the solute is non-volatile.
Related
Formula used
in m | Stock concentration (C1) | % | 10 | 0 in v | Stock volume (V1) | mL | 100 | 0 in p | Final concentration (C2) | % | 2 | 0 out v2 | Final volume (V2) | mL | m * v / p | 2 out w | Solute mass at C1 | g | m * v / 100 | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- QPP Calculator Canada: How It Works & How to Use It
- PPP Calculator World Bank: How It Works & How to Use It2,000.00
- PPP Calculator: India vs USA Cost Comparison1,000.00 USD
- PPP Calculator USD to INR: How It Works2,335 INR
- PPP Calculator India vs UK: Real Cost Comparison103.63 GBP
- PPP Calculator India vs Dubai: Real Cost Comparison8,954.58 AED