Calculate the reaction enthalpy change, ΔH, from coffee cup calorimetry by measuring the temperature change and using qsolution = m c ΔT; at constant pressure, ΔH for the reaction is approximately −qsolution divided by the moles reacted. Enter solution mass, specific heat capacity, temperature change, and reacted amount to estimate ΔH per mole.
Formula
First calculate the heat gained or lost by the solution:
qsolution = m cp ΔT
Then estimate the reaction enthalpy per mole:
ΔHrxn = −qsolution / n
- m is the total solution mass in grams (g).
- cp is the solution’s specific heat capacity in joules per gram per degree Celsius (J/(g·°C)).
- ΔT is final temperature minus initial temperature, in °C. A positive value means the solution warmed.
- qsolution is heat transferred to the solution, in joules (J).
- n is the amount, in moles, of the limiting reactant consumed according to the balanced reaction.
- ΔHrxn is the estimated reaction enthalpy in kilojoules per mole (kJ/mol). The factor 1000 converts joules to kilojoules.
The minus sign follows energy conservation: if the solution warms, it gained heat and the reaction released it. This calculation assumes the calorimeter is at constant pressure, so the reaction heat corresponds to enthalpy change under the experiment’s conditions.
Worked Example
Using the calculator’s default values, the solution has a mass of 100 g, a specific heat capacity of 4.184 J/(g·°C), a temperature rise of 5 °C, and 0.0500 mol of limiting reactant consumed.
- Calculate heat absorbed by the solution: qsolution = (100 g)(4.184 J/(g·°C))(5 °C) = 2092 J.
- Assign the opposite heat to the reaction: qrxn ≈ −2092 J.
- Convert to kilojoules per mole: ΔHrxn = −2092 J / (1000 J/kJ × 0.0500 mol) = −41.84 kJ/mol.
The calculator displays −41.84 kJ/mol and 2092.00 J. The negative enthalpy indicates an exothermic reaction: the reaction released heat while the solution warmed.
Assumptions
- The reaction occurs at approximately constant atmospheric pressure.
- The solution’s mass and heat capacity are represented by the entered values; 4.184 J/(g·°C) is the approximate specific heat capacity of water, not a universal value for every solution.
- Heat absorbed by the cup, thermometer, and surroundings is negligible.
- The measured temperature change captures the reaction’s relevant heat exchange, and the stated moles are the limiting reactant amount consumed.
How Coffee Cup Calorimetry Works
A coffee cup calorimeter is a simple, insulated container used to estimate heat transfer in solution reactions. The cup reduces heat exchange with the surroundings, while a temperature probe or thermometer tracks the solution’s temperature. Because the cup is open to the atmosphere, the experiment is commonly treated as a constant-pressure measurement.
The calculation uses the solution as the measured part of the system. If it gains heat, the reaction generally loses the same amount: qrxn ≈ −qsolution. This is an approximation, because the cup and other equipment may also absorb heat. If their heat capacity is known, their contribution can be included as an additional term: qcalorimeter = CcalΔT, where Ccal is the calorimeter heat capacity in J/°C. Then use ΔH ≈ −(qsolution + qcalorimeter)/n, with consistent units.
Choosing Inputs and Reading the Result
Use the total mass of the mixed solution when applying the solution-only formula. If the experiment records volumes instead, convert them to mass using appropriate densities; assuming 1.00 g/mL is an approximation suitable mainly for dilute, water-like solutions. The heat capacity should likewise match the mixture when a reliable value is available. Otherwise, using water’s 4.184 J/(g·°C) should be identified as an estimate.
Determine n from the balanced chemical equation, not simply from the amount of whichever reagent is easiest to measure. For a reaction A + 2B → products, for instance, one mole of reaction consumes one mole of A and two moles of B. Find the limiting reactant and express the reaction extent in moles using the balanced coefficients. Report the basis clearly, such as kJ per mole of reaction as written or kJ per mole of a named reactant.
- A positive ΔT usually gives a negative ΔH: heat was released by the reaction.
- A negative ΔT gives a positive ΔH: the solution cooled as the reaction absorbed heat.
- A temperature change near zero gives a small calculated heat, but does not prove that no reaction occurred; heat loss or measurement resolution may obscure the signal.
Common Errors and Limits
Keep units consistent. With mass in grams and heat capacity in J/(g·°C), q comes out in joules. Divide by 1000 to express energy in kilojoules before reporting kJ/mol. A temperature difference has the same numerical size in °C and K, so either difference unit works here; do not substitute an absolute temperature in kelvins for ΔT.
Use final minus initial for ΔT and retain its sign. Taking the absolute value removes information about whether the reaction was exothermic or endothermic. Another frequent error is dividing by the starting amount of a reagent that is in excess rather than by the correctly stoichiometric amount reacted.
The simplest formula omits heat absorbed by the cup and heat exchanged with the surroundings. It can therefore underestimate the magnitude of ΔH. Other limitations include incomplete reaction, evaporation, mixing delays, temperature-probe lag, and uncertainty in solution mass or heat capacity. Record the highest or lowest temperature consistently with the experimental method, and avoid implying precision beyond the measurements. For quantitative work, calibrate the calorimeter, account for its heat capacity, repeat measurements, and report uncertainty.
This result estimates enthalpy change for the actual reaction conditions and composition. It is not automatically a standard enthalpy of reaction: standard values refer to specified standard states and conditions, and experimental concentrations or temperatures may differ.
Frequently Asked Questions
Why is ΔH the negative of the solution heat?
The solution and reaction exchange heat. In the idealized energy balance, heat gained by the solution is released by the reaction, so qrxn ≈ −qsolution.
Is coffee cup calorimetry at constant pressure?
It is generally treated as constant-pressure calorimetry because the cup is open to the atmosphere. Under that condition, reaction heat at constant pressure corresponds to enthalpy change, subject to the experiment’s assumptions.
Can I use volume instead of solution mass?
Not directly in m c ΔT, which requires mass. Convert volume to mass using the solution’s density. Treating 1 mL as 1 g is only an approximation for water-like mixtures.
What does a positive ΔH mean in this calculation?
A positive value indicates an endothermic reaction estimate: the reaction absorbed heat, typically corresponding to a cooling solution and negative ΔT.
Should I include the cup’s heat capacity?
Include it when the calorimeter heat capacity is known and meaningful accuracy is needed. The cup’s heat is CcalΔT, added to the solution heat before reversing the sign to estimate reaction heat.
For bench work, follow your lab method, the safety data sheet (SDS), and your supervisor.
Related
Formula used
in m | Solution mass | g | 100 | 0 in cp | Specific heat capacity | J/(g·°C) | 4.184 | 0 in dt | Temperature change, final − initial | °C | 5 | - in n | Moles reacted | mol | 0.0500 | 0.000000001 out dh | Reaction enthalpy change | kJ/mol | -(m * cp * dt) / (1000 * n) | 2 out q | Heat absorbed by solution | J | m * cp * dt | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Skip Calculator for Soil: What It Can and Can’t Do7.500 m³
- USD to KPW Calculator: Convert Dollars to North Korean Won90,000.00 KPW
- OK Calculator on TV on the Radio? Meaning Explained
- Pension Calculator KP: Estimate Your Pension Benefits
- Neonatal Kp Calculator: What It Means80.0000 mmol/mmol
- Newton to kp Converter Calculator and Formula1.0000 kp