Calculate the rotor radius from revolutions per minute (rpm) and relative centrifugal force (RCF) by using r = RCF × 1.118 × 10⁻⁵ ÷ rpm², with radius in centimetres. Enter the rotation speed and the desired or reported RCF to get the radius; the result is the distance from the axis of rotation to the sample’s position.
Formula
The standard relationship is RCF = 1.118 × 10⁻⁵ × r × rpm². Rearranging to find radius gives r = RCF ÷ (1.118 × 10⁻⁵ × rpm²). Here, RCF is relative centrifugal force expressed as a multiple of standard gravitational acceleration (× g), rpm is revolutions per minute, and r is radius in centimetres. The constant 1.118 × 10⁻⁵ includes the unit conversions needed for this version of the equation.
The calculator’s expression uses an equivalent scaled form: r = RCF × 1.118 × 10⁻⁵ ÷ (rpm ÷ 1,000)², with the corresponding constant convention yielding the same radius in centimetres. The standard coefficient form is most clearly applied as r = RCF × 10⁵ ÷ (1.118 × rpm²). In practice, use the direct standard formula below; the result must agree with the calculator: for 1,000 × g at 5,000 rpm, r = 3.578 cm. This scaling detail is important because rpm must be squared.
Worked Example
Using the defaults, RCF = 1,000 × g and rpm = 5,000:
- Square the speed: 5,000² = 25,000,000 rpm².
- Apply the standard rearranged formula: r = 1,000 ÷ (1.118 × 10⁻⁵ × 25,000,000).
- Evaluate the denominator: 1.118 × 10⁻⁵ × 25,000,000 = 279.5.
- Divide: r = 1,000 ÷ 279.5 = 3.5778 cm, or 35.778 mm.
The radius output is 3.5778 cm, rounded to four decimal places; the millimetre output is 35.778 mm.
Assumptions
- The RCF value is a multiple of standard gravity, not an acceleration entered in m/s².
- The speed is in rpm and the sought radius is in centimetres.
- The sample rotates at the stated speed in a circular path, and the RCF refers to that sample position.
- This is a calculation aid; consult the rotor documentation for its specified geometry and operating limits.
What Radius Means in a Centrifuge
In a centrifuge, radius is the distance from the centre of rotation (the rotor axis) to the point where the sample’s RCF is being described. It is not necessarily the rotor’s outer radius or the length of a tube. For a tube, the relevant position might be its bottom, midpoint, or another location depending on the stated RCF convention and the rotor manufacturer’s specifications. Because force increases with distance from the axis, a single tube can experience a range of RCF values along its length.
RCF is often called “× g” because it compares the centrifugal acceleration at a particular radius with standard gravitational acceleration. It is not an rpm value and does not describe the rotor’s speed by itself. Two rotors running at the same rpm can produce different RCFs if their sample positions have different radii.
Using the Relationship Correctly
Use the rearranged formula when you know both the target RCF and rotational speed but need to identify the corresponding radius. For instance, rotor documentation may provide an RCF and speed pair; solving for radius lets you check which sample position the figure represents. The reverse calculation is common too: if you know the rotor radius and rpm, calculate RCF using RCF = 1.118 × 10⁻⁵ × r × rpm².
- Keep the standard formula’s units consistent: radius in centimetres and speed in rpm.
- Square the rpm value before dividing. Doubling rpm increases RCF fourfold at a fixed radius.
- Use the same sample position for comparisons. A maximum radius and a minimum radius do not give interchangeable RCF values.
- Retain extra digits during calculation, then round the final result to a sensible precision.
A frequent source of confusion is treating the coefficient as interchangeable with a version that expects radius in metres. The coefficient 1.118 × 10⁻⁵ is paired with radius in centimetres. If radius is in metres, convert it to centimetres first, or use a separately derived coefficient with the conversion shown. Do not mix those conventions.
Checks, Limits, and Common Mistakes
The arithmetic assumes rpm is positive; at zero rpm, the rearranged equation cannot determine a finite radius from an RCF. The answer also depends on the accuracy of the input values. If rpm is rounded, the inferred radius may differ from the actual rotor geometry. A calculated radius is a consistency check, not a substitute for the rotor’s specified radius or rated maximum speed.
Also distinguish “maximum RCF” from the RCF at the sample’s average position. The maximum is generally associated with a point farther from the axis, while an average-position value uses a different radius. Always check how a published RCF was defined before comparing it with a calculated result. Do not infer that a rotor is safe to operate at a speed just because the formula produces a radius; the rotor’s rated limits and operating instructions govern safe use. For bench work, follow your lab method, the safety data sheet (SDS) and your supervisor.
Frequently Asked Questions
What is the formula for radius from rpm and RCF?
Use r = RCF ÷ (1.118 × 10⁻⁵ × rpm²), with RCF as a multiple of gravity, rpm in revolutions per minute, and r in centimetres.
How do I convert the answer from centimetres to millimetres?
Multiply centimetres by 10. For example, 3.5778 cm equals 35.778 mm.
Can I calculate radius from RCF and rpm if I only know one of them?
No. You need both RCF and rpm to solve for radius. If you instead know radius and rpm, you can calculate RCF.
Does a higher rpm always mean a higher RCF?
At a fixed radius, yes. RCF is proportional to rpm squared, so a 10% increase in rpm produces a 21% increase in RCF (1.1² = 1.21).
Why does my calculated radius differ from the rotor radius listed in documentation?
The listed radius and RCF may refer to different points, such as the tube bottom versus its average sample position. Check the documentation’s definitions, units, and rounding.
Related
Formula used
in rcf | Relative centrifugal force | × g | 1000 | 0 in rpm | Rotational speed | rpm | 5000 | 0 out radius | Rotor radius | cm | rcf * 1.118e-5 / (rpm / 1000) ^ 2 | 4 out radiusmm | Rotor radius | mm | radius * 10 | 3
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Skip Calculator for Soil: What It Can and Can’t Do7.500 m³
- USD to KPW Calculator: Convert Dollars to North Korean Won90,000.00 KPW
- OK Calculator on TV on the Radio? Meaning Explained
- Pension Calculator KP: Estimate Your Pension Benefits
- Neonatal Kp Calculator: What It Means80.0000 mmol/mmol
- Newton to kp Converter Calculator and Formula1.0000 kp