A carbon equivalent calculator converts a steel’s alloy percentages into a single CEV (carbon equivalent value) number that predicts weldability and hardenability. You enter the weight percentages of carbon, manganese, chromium, molybdenum, vanadium, nickel, and copper, and the calculator returns the CEV using the IIW formula (or the PCM formula if you choose it). This number tells you how likely the steel is to harden and crack during welding, so you can set preheat and welding procedures accordingly.
Formula
The most widely used carbon equivalent formula is the IIW (International Institute of Welding) equation:
CEV = C + Mn/6 + (Cr + Mo + V)/5 + (Ni + Cu)/15
All element values are weight percentages (wt%). The formula adds the hardening contribution of each alloying element, scaled by how strongly it promotes martensite formation relative to carbon. Carbon itself has the largest coefficient (1), followed by manganese (1/6), then chromium, molybdenum, and vanadium (1/5), and finally nickel and copper (1/15).
The alternative PCM (welding cracking parameter, also called Ito–Bessyo) formula is:
PCM = C + Si/30 + (Mn + Cu + Cr)/20 + Ni/60 + Mo/15 + V/10 + 5B
PCM includes silicon and boron, which the IIW formula ignores. It is often used for higher-strength low-alloy steels because it correlates better with cold cracking in those grades.
Worked Example
Take a typical structural steel with the default values: C = 0.20%, Mn = 1.40%, Cr = 0.30%, Mo = 0.10%, V = 0.05%, Ni = 0.20%, Cu = 0.20%. Using the IIW formula:
- Mn/6 = 1.40 / 6 = 0.2333
- (Cr + Mo + V)/5 = (0.30 + 0.10 + 0.05) / 5 = 0.45 / 5 = 0.09
- (Ni + Cu)/15 = (0.20 + 0.20) / 15 = 0.40 / 15 = 0.0267
- CEV = 0.20 + 0.2333 + 0.09 + 0.0267 = 0.550
So the CEV is 0.550%. For the same steel, PCM = 0.20 + 0/30 + (1.40 + 0.20 + 0.30)/20 + 0.20/60 + 0.10/15 + 0.05/10 + 5×0 = 0.20 + 0.095 + 0.0033 + 0.0067 + 0.005 = 0.310%. The CEV is higher because the IIW formula weights manganese more heavily.
Assumptions
- All element concentrations are weight percentages of the total steel composition.
- The formulas assume the steel is a low-alloy or carbon-manganese steel, not a highly alloyed stainless or tool steel.
- The CEV is an empirical index, not a physical property; it predicts relative weldability based on composition alone.
- The formulas do not account for section thickness, joint restraint, hydrogen level, or preheat—those must be considered separately.
How to Read the Result
Higher CEV means greater hardenability, which increases the risk of hydrogen-induced cold cracking in the heat-affected zone (HAZ). General guidelines for structural steels:
- CEV < 0.35%: Excellent weldability, usually no preheat needed for thin sections.
- CEV 0.35–0.45%: Good weldability; preheat may be required for thick sections or high restraint.
- CEV 0.45–0.55%: Moderate weldability; preheat and controlled heat input are typically required.
- CEV > 0.55%: Poor weldability; high preheat, low hydrogen processes, and careful procedure qualification are essential.
These thresholds are approximate and vary with code and application. For example, EN 1011-2 recommends maximum CEV values for certain steel grades, and some specifications set a maximum CEV of 0.40% for structural steel to ensure weldability without preheat.
Common Mistakes and Misconceptions
A frequent error is using the CEV formula with element percentages that are not from the same heat or not in weight percent. Always use the product analysis (check certificate) or the specified range, not a mix of both.
Another misconception is that CEV alone tells you whether a weld will crack. It does not. It is only one input in the preheat calculation. The actual risk depends on hydrogen level (from the welding consumable), restraint, and cooling rate (which depends on thickness and heat input). A low CEV steel can still crack if welded with a high-hydrogen electrode in a highly restrained joint.
Also, note that the IIW formula ignores silicon and boron. If your steel contains significant boron (e.g., >0.0005%), use the PCM formula instead, because boron strongly increases hardenability.
When to Use CEV vs. PCM
Use the IIW CEV for most carbon-manganese and low-alloy steels, especially when comparing to specifications that quote CEV limits. Use PCM when:
- The steel contains boron or silicon above trace levels.
- The steel is a high-strength low-alloy (HSLA) grade with yield strength above 450 MPa.
- You are following a standard that specifically requires PCM, such as some API or offshore specifications.
Both formulas give a number in percent, but they are not interchangeable. A steel with CEV 0.40% might have PCM 0.25%, and the preheat recommendation based on each will differ. Always use the formula that the relevant standard or contract specifies.
Limits of the Carbon Equivalent
The CEV is a simple empirical index developed decades ago. It does not capture:
- The effect of grain size, which influences hardenability.
- The presence of microalloying elements like niobium, titanium, or aluminum in amounts not included in the formula.
- The role of residual elements like sulfur and phosphorus, which can cause hot cracking.
- The influence of heat treatment or thermomechanical processing on the final microstructure.
For critical applications, weldability is assessed by welding procedure qualification tests (e.g., CTS tests, implant tests) rather than by CEV alone. The CEV is a screening tool, not a guarantee.
Frequently Asked Questions
What is a good carbon equivalent value for welding? A CEV below 0.40% is generally considered good for welding without special precautions. Values between 0.40% and 0.55% require preheat and controlled heat input. Above 0.55%, welding becomes difficult and requires high preheat and low-hydrogen practices.
How do I calculate carbon equivalent from a mill certificate? Take the weight percentages of C, Mn, Cr, Mo, V, Ni, and Cu from the mill certificate and plug them into the IIW formula: CEV = C + Mn/6 + (Cr+Mo+V)/5 + (Ni+Cu)/15. Make sure all values are in wt%, not ppm.
What is the difference between CEV and PCM? CEV (IIW) is the traditional formula that includes C, Mn, Cr, Mo, V, Ni, Cu. PCM (Ito–Bessyo) adds silicon and boron and uses different coefficients; it is better for high-strength steels. PCM values are usually lower than CEV for the same steel.
Why does carbon equivalent matter for welding? It predicts the maximum hardness in the heat-affected zone, which correlates with cold cracking risk. Higher CEV means more martensite forms on cooling, which is harder and more susceptible to hydrogen embrittlement.
Can I use the carbon equivalent for stainless steel? No. The formulas are calibrated for carbon and low-alloy steels. Stainless steels have different metallurgy (e.g., ferritic, austenitic) and different cracking mechanisms, so CEV is not applicable.
Does preheat depend only on CEV? No. Preheat is determined by CEV, combined plate thickness, hydrogen level of the welding consumable, and heat input. Standards like EN 1011-2 provide graphs that use CEV and thickness to recommend minimum preheat temperatures.
Related
Formula used
in c | Carbon, C (%) | % | 0.20 | 0 | 2 in mn | Manganese, Mn (%) | % | 1.40 | 0 | 5 in cr | Chromium, Cr (%) | % | 0.30 | 0 | 5 in mo | Molybdenum, Mo (%) | % | 0.10 | 0 | 3 in v | Vanadium, V (%) | % | 0.05 | 0 | 2 in ni | Nickel, Ni (%) | % | 0.20 | 0 | 5 in cu | Copper, Cu (%) | % | 0.20 | 0 | 3 sel formula | Formula | IIW CEV = 1, PCM = 2 out cev | Carbon equivalent (CEV) | % | c + mn/6 + (cr + mo + v)/5 + (ni + cu)/15 | 3 out pcm | Welding cracking parameter (PCM) | % | c + si/30 + (mn + cu + cr)/20 + ni/60 + mo/15 + v/10 + 5*b | 3
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Normality to g/L Converter & Formula29.220 g/L
- Normality to meq/mL Conversion Calculator1.0000 meq/mL
- Normality Test Q-Q Plot: How to Read It
- Normality Test Results: How to Analyze Them
- Normality Slay the Spire?
- Normality Test for Paired t Test: How to Check