This centrifuge rpm-to-RCF calculator converts rotational speed in revolutions per minute (rpm) and rotor radius into relative centrifugal force (RCF, or ×g). Enter the rpm and the radius in centimeters; the calculator returns the force relative to Earth’s gravity, which is the value commonly used to specify centrifugation conditions.
Formula
The formula is:
RCF = 1.118 × 10−5 × r × rpm2
- RCF is relative centrifugal force, expressed as a multiple of standard gravitational acceleration, ×g. It is a ratio, not a force measured in newtons.
- r is the rotor radius in centimeters, measured from the axis of rotation to the sample location being considered.
- rpm is rotational speed in revolutions per minute.
- 1.118 × 10−5 is the conversion constant for this formula when radius is in centimeters and speed is in rpm.
The formula comes from centripetal acceleration, a = ω²r, divided by standard gravity, with the rpm, radius, and unit conversions included in the constant. The key consequence is that force is proportional to radius but to the square of speed: doubling rpm produces four times the RCF at the same radius.
Worked Example
Using the calculator’s default values—10,000 rpm and a 10 cm radius:
- Square the speed: 10,0002 = 100,000,000.
- Multiply by radius and the formula constant: RCF = 1.118 × 10−5 × 10 × 100,000,000.
- Calculate: RCF = 11,180 ×g.
The result is 11,180.00 ×g. This is the acceleration relative to standard gravity at the specified 10 cm radius; it is not a universal result for every rotor operating at 10,000 rpm.
Assumptions
- The entered radius is the distance from the rotor’s axis to the sample point of interest, in centimeters.
- The entered rpm is the rotor’s actual operating speed.
- The output represents the ideal radial acceleration at that radius. It does not account for rotor geometry, sample movement, acceleration or braking ramps, or the characteristics of the material being centrifuged.
- Use the rotor’s approved operating limits and instructions; this calculation does not establish that a speed is safe for a rotor.
How to Choose the Radius
Radius is the distance from the center of rotation to the point in the sample for which you want to know the force. It is not the rotor’s outside diameter, and it is not automatically half the rotor’s diameter. Rotor manufacturers commonly specify more than one useful radius:
- Minimum radius, rmin: distance to the top or innermost part of the sample position.
- Maximum radius, rmax: distance to the bottom or outermost part of the sample position.
- Average radius, ravg: a representative value between those points, when appropriate for the method.
Because radius changes along the tube, the RCF also varies along the sample. If a protocol gives a single RCF without saying which radius it uses, consult the protocol’s definition or the rotor documentation rather than guessing. For a result at a specific point, enter that point’s radius. If a method specifies maximum RCF, use the corresponding maximum radius—not an average radius.
Using RCF to Set a Centrifuge
Laboratory methods often specify RCF because it describes the acceleration applied to a sample more directly than rpm does. A target such as 5,000 ×g can be reproduced on different rotors by choosing the rpm that gives that RCF at the radius convention used by the method. The same rpm alone does not guarantee the same force on different equipment.
To convert a target RCF back to speed, rearrange the formula:
rpm = √(RCF ÷ (1.118 × 10−5 × r))
For example, at a 10 cm radius, a target of 5,000 ×g requires approximately 6,688 rpm: √(5,000 ÷ (1.118 × 10−5 × 10)) ≈ 6,688. This is a mathematical conversion, not a recommendation to run any particular rotor at that speed. Check that the required rpm is within the limits for the rotor, tubes, adapters, and centrifuge.
Common Conversion Mistakes
- Confusing rpm with RCF: rpm describes how fast the rotor turns; RCF describes acceleration relative to gravity. They are different quantities.
- Using diameter instead of radius: entering a 20 cm diameter as a 20 cm radius doubles the calculated RCF. Measure from the axis to the sample point.
- Using the wrong radius units: this formula requires centimeters. A radius given in millimeters must be divided by 10 before entry; a radius in meters must be multiplied by 100.
- Assuming a universal rpm-to-RCF conversion: the conversion depends on radius. A speed-to-force conversion without rotor geometry is incomplete.
- Rounding the speed too early: since rpm is squared, a small speed difference can have a larger effect on calculated RCF. Keep the calculator’s unrounded inputs and round the displayed result only as needed.
- Mixing radius conventions: a protocol based on rmax may not match a result calculated with ravg. Confirm the convention before comparing values.
Limits and Safe Use
This calculation gives radial acceleration at a selected radius. It does not predict sedimentation time, separation quality, pellet formation, or sample recovery; those depend on factors such as particle size and density, liquid viscosity, rotor design, and the method’s operating conditions. It also does not account for how acceleration and deceleration settings affect a particular separation.
Never treat a calculated rpm as permission to exceed equipment limits. Rotor ratings can depend on the rotor’s condition, compatible buckets or adapters, and the vessels used. Follow the centrifuge and rotor instructions, the applicable laboratory method, and your lab’s safety procedures. Where bench work is implied, follow your lab method, the safety data sheet (SDS), and your supervisor.
Frequently Asked Questions
How do I convert rpm to RCF?
Multiply 1.118 × 10−5 by the radius in centimeters and by rpm squared: RCF = 1.118 × 10−5 × r × rpm2.
Can I calculate RCF without knowing the rotor radius?
No. The force depends on radius as well as rpm. Find the relevant radius in the rotor documentation or method before converting.
Is 1,000 rpm equal to 1,000 ×g?
No. Rpm is rotational speed, while ×g is relative centrifugal force. Their numerical values are not directly interchangeable, and the relationship depends on radius.
Should I use maximum or average radius?
Use the radius specified by the laboratory method or required RCF convention. If the method does not say, check its source or rotor documentation; different radius choices give different results.
Does the calculator tell me the safe maximum speed?
No. It only performs a mathematical conversion. Use the approved limits for the rotor, centrifuge, tubes, and adapters, and do not exceed any applicable rating.
Related
Formula used
in rpm | Rotor speed | rpm | 10000 | 0 in r | Rotor radius | cm | 10 | 0 out rcf | Relative centrifugal force | ×g | 1.118e-5 * r * rpm ^ 2 | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- MD Calc I:T Ratio Calculator and Explanation0.0500 ratio
- Oxygen Mass Number: Isotope Values Explained16 nucleons
- Mass-to-Light Ratio: Meaning and Calculation1.000 M☉/L☉
- M/z Ratio in Mass Spectrometry: Meaning and Calculation1,000.00 Th
- Mass Fraction to Molar Fraction Calculator
- K2 Molar Mass Calculator and Calculation78.1966 g/mol