molecalculator

Moles & Molar Mass

Enthalpy Definition in Chemistry

Calculator No. 01-9292 · Updated · Formula and assumptions shown below

Amount of substance 1.0000 mol
Enthalpy change per mole
1,000.00 J/mol
= Heat absorbed (q) ÷ Amount of substance
Mass of substance
18.015 g
Set in the form below
Molar mass
18.015 g/mol
Set in the form below
You enter
Mass of substance (g), Molar mass (g/mol), Heat absorbed (q) (J)
You get
Amount of substance (mol), Enthalpy change per mole (J/mol)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Enthalpy (H) is the total heat content of a system at constant pressure, defined as H = U + PV, where U is internal energy, P is pressure, and V is volume. In chemistry, the change in enthalpy (ΔH) measures the heat absorbed or released during a reaction at constant pressure, which is why it is the standard quantity for describing reaction energetics.

Formula

The fundamental definition is:

H = U + PV

where H is enthalpy (J), U is internal energy (J), P is pressure (Pa), and V is volume (m³). For a chemical reaction at constant pressure, the change in enthalpy is:

ΔH = ΔU + PΔV

In practice, ΔH equals the heat exchanged (qp) at constant pressure: ΔH = qp. The calculator above computes the enthalpy change per mole of substance from the heat absorbed and the amount of substance (n = m / M).

Worked Example

Using the defaults: mass of water = 18.015 g, molar mass = 18.015 g/mol, heat absorbed = 1000 J.

Step 1: Calculate moles of water:

n = 18.015 g / 18.015 g/mol = 1.000 mol

Step 2: Enthalpy change per mole:

ΔH = q / n = 1000 J / 1.000 mol = 1000.00 J/mol

The calculator shows 1000.00 J/mol, matching the step-by-step result.

Assumptions

  • Constant pressure (usually atmospheric pressure).
  • No work other than pressure-volume work.
  • The substance is pure and the heat capacity is constant over the temperature range.
  • For the calculator, the heat absorbed q is given as a positive value (endothermic) or negative (exothermic).

Why Enthalpy, Not Internal Energy?

Most chemical reactions in the lab and in biology happen in open containers at constant atmospheric pressure, not at constant volume. When a reaction produces or consumes gas, the volume changes, and the system does work on the surroundings (or vice versa). Enthalpy automatically accounts for that pressure-volume work, so ΔH directly gives the heat you would measure with a calorimeter at constant pressure. Internal energy (ΔU) is the quantity for constant-volume processes, like in a bomb calorimeter, and the two differ by the PΔV term.

Endothermic vs. Exothermic Reactions

The sign of ΔH tells you the direction of heat flow:

  • Negative ΔH (exothermic): heat is released to the surroundings. Examples: combustion of methane (ΔH = −890 kJ/mol), neutralization of a strong acid and base (ΔH ≈ −57 kJ/mol).
  • Positive ΔH (endothermic): heat is absorbed from the surroundings. Examples: melting ice (ΔH = +6.01 kJ/mol), thermal decomposition of calcium carbonate (ΔH = +178 kJ/mol).

A common misconception is that exothermic reactions are always spontaneous. That is false—spontaneity depends on both enthalpy and entropy (Gibbs free energy, ΔG = ΔH − TΔS). Some endothermic reactions, like dissolving ammonium nitrate in water, are spontaneous because the entropy increase outweighs the heat absorbed.

Standard Enthalpy of Formation and Reaction

Because enthalpy is a state function (its value depends only on the current state, not the path), you can calculate ΔH for any reaction using tabulated standard enthalpies of formation (ΔHf°). The standard enthalpy of formation is the heat change when one mole of a compound forms from its elements in their standard states at 1 bar and a specified temperature (usually 25 °C). For elements in their standard state, ΔHf° = 0.

For a reaction aA + bB → cC + dD:

ΔHrxn° = [cΔHf°(C) + dΔHf°(D)] − [aΔHf°(A) + bΔHf°(B)]

Example: combustion of methane, CH4(g) + 2O2(g) → CO2(g) + 2H2O(l). Using ΔHf° values: CH4 = −74.8 kJ/mol, CO2 = −393.5 kJ/mol, H2O(l) = −285.8 kJ/mol, O2 = 0. ΔHrxn° = [−393.5 + 2(−285.8)] − [−74.8 + 0] = −965.1 + 74.8 = −890.3 kJ/mol.

Measuring Enthalpy Changes

In the lab, you measure ΔH using calorimetry. A simple coffee-cup calorimeter (two Styrofoam cups, a thermometer, a stirrer) works for reactions in solution at constant pressure. You measure the temperature change of a known mass of solution, then calculate q = mcΔT, where m is the mass of the solution, c is its specific heat capacity (often approximated as 4.18 J/(g·°C) for dilute aqueous solutions), and ΔT is the temperature change. That q equals ΔH for the reaction (with sign depending on heat flow). For accurate work, you must correct for heat absorbed by the calorimeter itself (the calorimeter constant).

Bomb calorimeters measure ΔU at constant volume, then you convert to ΔH using the ideal gas relation ΔH = ΔU + ΔngasRT, where Δngas is the change in moles of gas.

Common Mistakes and Misconceptions

  • Confusing ΔH with total enthalpy: You never measure absolute H; only changes (ΔH) matter in chemistry.
  • Forgetting the state of matter: ΔHf° for water vapor is different from liquid water (−241.8 vs. −285.8 kJ/mol). Always specify (s), (l), (g), or (aq).
  • Sign errors: If a reaction is reversed, the sign of ΔH flips. If you multiply a reaction by a coefficient, ΔH multiplies by the same factor.
  • Using the wrong heat capacity: For solutions, use the solution’s specific heat, not the pure solvent’s, unless the solution is very dilute.
  • Ignoring pressure-volume work: For reactions with gas evolution, ΔH and ΔU differ noticeably. At 25 °C, 1 mole of gas at 1 atm occupies about 24.5 L, so PΔV ≈ 2.5 kJ per mole of gas produced.

Frequently Asked Questions

What is the difference between enthalpy and heat?

Heat is energy in transit due to a temperature difference. Enthalpy is a state function that includes internal energy plus the product of pressure and volume. At constant pressure, the heat absorbed or released equals the change in enthalpy (ΔH = qp), which is why the two are often used interchangeably in open-air chemistry.

Can enthalpy be negative?

Yes, the change in enthalpy (ΔH) can be negative for exothermic reactions, meaning the system releases heat. The absolute enthalpy (H) of a substance is always positive relative to a reference state, but it is never measured directly.

Why is enthalpy a state function?

Because it is defined as H = U + PV, and both internal energy (U), pressure (P), and volume (V) are state functions. The value of H depends only on the current state of the system, not on how it got there. This allows you to calculate ΔH using Hess’s law and formation enthalpies without performing the reaction.

What is the unit of enthalpy?

The SI unit is the joule (J). In chemistry, you often see kilojoules per mole (kJ/mol) for molar enthalpy changes, or kilojoules (kJ) for the total change. Older texts use calories (cal), where 1 cal = 4.184 J.

Does enthalpy change with temperature?

Yes, enthalpy of a substance depends on temperature because it includes internal energy, which increases with temperature. The enthalpy change for a reaction also varies slightly with temperature, given by Kirchhoff’s law: ΔH(T2) = ΔH(T1) + ΔCp(T2 − T1), where ΔCp is the difference in heat capacities between products and reactants.

Related

Formula used
in m | Mass of substance | g | 18.015 | 0
in mm | Molar mass | g/mol | 18.015 | 0.001
in q | Heat absorbed (q) | J | 1000 | 0
out n | Amount of substance | mol | m / mm | 4
out dh | Enthalpy change per mole | J/mol | q / n | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →