molecalculator

Moles & Molar Mass

Gas Cv Calculator: Heat Capacity Ratio and Formula

Calculator No. 01-3965 · Updated · Formula and assumptions shown below

Molar heat capacity at constant volume Cv 20.786 J/(mol·K)
Heat-capacity ratio γ = Cp/Cv
1.4000
Result, rounded to 4 decimal places
Mass-specific Cv
741.970 J/(kg·K)
= Molar heat capacity at constant volume Cv × 1000 ÷ Molar mass
Molar heat capacity at constant pressure Cp
29.1 J/(mol·K)
Set in the form below
You enter
Molar heat capacity at constant pressure Cp (J/(mol·K)), Molar mass (g/mol)
You get
Molar heat capacity at constant volume Cv (J/(mol·K)), Heat-capacity ratio γ = Cp/Cv, Mass-specific Cv (J/(kg·K))
Rounding
3 dp · 4 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

A gas Cv calculator determines a gas’s heat capacity at constant volume, usually from its heat capacity at constant pressure and the gas constant. Enter Cp and the gas’s molar mass to calculate Cv in J/(mol·K) and the dimensionless heat-capacity ratio γ; the result assumes an ideal gas.

Formula

For an ideal gas, the molar heat capacities at constant pressure and constant volume are related by Mayer’s relation:

Cv = Cp − R

Here, Cp is molar heat capacity at constant pressure in J/(mol·K), Cv is molar heat capacity at constant volume in J/(mol·K), and R is the universal gas constant, 8.31446261815324 J/(mol·K). The heat-capacity ratio is γ = Cp/Cv, with no units. To express Cv per unit mass, convert the molar mass M from g/mol to kg/mol: Cv,mass = Cv × 1000/M, in J/(kg·K).

This page uses Cp as an input because its value depends on the gas and, in real gases, can vary with temperature and pressure. The calculator does not identify a gas or look up its heat capacity. For a different gas or temperature, supply an appropriate Cp value from a reliable reference or measurement. The default values are a representative near-room-temperature example for nitrogen gas, not universal constants.

Worked Example

Using the calculator’s default values, Cp = 29.100 J/(mol·K) and M = 28.014 g/mol:

  1. Molar Cv: Cv = Cp − R = 29.100 − 8.31446261815324 = 20.78553738184676 J/(mol·K), which rounds to 20.786 J/(mol·K).
  2. Heat-capacity ratio: γ = Cp/Cv = 29.100/20.78553738184676 = 1.3990, to four decimal places.
  3. Mass-specific Cv: 20.78553738184676 × 1000/28.014 = 741.96 J/(kg·K), to three decimal places: 741.963 J/(kg·K).

The reported figures are rounded only for display. The ratio and mass-specific result use the unrounded Cv value, not the displayed 20.786.

Assumptions

  • The gas is treated as ideal, so Cp − Cv equals the universal gas constant on a molar basis.
  • Cp is a molar heat capacity for the same gas and temperature range as the desired Cv.
  • M is the gas’s molar mass in g/mol; the calculator converts it to kg/mol for the mass-specific output.
  • Heat capacities are treated as constant over the conditions being considered. Real-gas effects and temperature-dependent changes are not modeled.

What Cv Means and When to Use It

Cv describes how much heat energy per mole is needed to raise a gas’s temperature by one kelvin while its volume is held constant. Its units, J/(mol·K), make the quantity a molar heat capacity. A mass-specific heat capacity instead refers to one kilogram and is reported in J/(kg·K). The calculator provides both so results can be matched to the units used in a calculation.

Constant volume matters because heating a gas at fixed volume does not make it expand and do pressure-volume work on its surroundings. At constant pressure, a gas can expand as it warms, so its molar heat capacity Cp is greater than Cv for an ideal gas. The difference is R—not because every gas has the same Cp, but because the ideal-gas relationship fixes the difference between the two molar heat capacities.

Use Cv in ideal-gas thermodynamics when the process or equation calls for heat capacity at constant volume, such as relating a temperature change to internal-energy change for a fixed amount of gas under suitable assumptions. Use Cp for constant-pressure heat calculations. Do not substitute one for the other simply because both describe heating.

How to Choose Inputs and Read the Results

  • Enter Cp in J/(mol·K). If a source reports kJ/(kmol·K), that number has the same numerical value as J/(mol·K). If it reports J/(kg·K), convert to a molar basis before entering it.
  • Enter molar mass in g/mol. For a mixture, use a molar mass and heat capacity appropriate to that mixture; a pure-gas value may not represent it.
  • Read Cv first. The first output is the molar constant-volume heat capacity. The next output, γ, is dimensionless and is useful in ideal-gas relations that specifically require the heat-capacity ratio.
  • Use mass-specific Cv when needed. This is convenient when mass, rather than moles, is the basis of an energy balance. Confirm that the rest of that calculation uses compatible units.

For a simple ideal gas with nearly constant heat capacities, γ can be interpreted as the ratio Cp/Cv. A value near 1.4 is common for some diatomic gases around room temperature, but it is not a universal gas constant or a fixed value for every gas and condition. Molecular structure and temperature affect heat capacity, especially when additional molecular energy modes become accessible.

Limits, Comparisons, and Common Mistakes

The central limitation is the ideal-gas assumption. For a real gas at elevated pressure or near condensation, Cp − Cv need not equal R; the difference can depend on pressure, temperature, and the gas’s equation of state. This calculator is therefore a transparent ideal-gas estimate, not a real-gas property database. For high-accuracy engineering work, use validated property data or an appropriate real-gas model at the actual state.

Another common mistake is mixing molar and mass-specific units. Cp in J/(kg·K) cannot be combined directly with R in J/(mol·K). Convert consistently first. Likewise, a value in kJ/(kg·K) must be converted to J/(kg·K) before any conversion to a molar basis. Check whether a reference reports heat capacity per mole, per kilogram, or per kilomole.

Do not confuse Cv with γ: Cv has units, while γ does not. Nor should Cp be interpreted as a single fixed number for all temperatures. Tabulated or measured heat capacities may be averages over a range or values at a specified temperature. Use data matching the conditions and precision required; excessive displayed decimal places do not make uncertain input data more accurate.

If Cp is less than or equal to R, the ideal-gas formula gives Cv at or below zero, which is not a physically reasonable heat capacity for an ordinary stable gas under the assumptions here. Treat that result as a signal to check the units, input value, or applicability of the model—not as a meaningful negative heat capacity.

Frequently Asked Questions

How do I calculate Cv for a gas?
For an ideal gas, subtract the universal gas constant from molar Cp: Cv = Cp − 8.31446261815324 J/(mol·K). Make sure Cp is expressed per mole in compatible units.

What is the difference between Cp and Cv?
Cp is heat capacity at constant pressure, while Cv is heat capacity at constant volume. For an ideal gas, Cp exceeds Cv by R on a molar basis because constant-pressure heating includes expansion work.

What is the formula for the heat-capacity ratio?
The ratio is γ = Cp/Cv. It has no units and is also called the adiabatic index in some contexts. Its value depends on the gas and conditions.

Can I calculate Cv from Cp for a real gas?
Not generally by subtracting R alone. That relation applies to an ideal gas. Real-gas heat capacities can require pressure, temperature, and a suitable real-fluid property model.

How do I convert molar Cv to J/(kg·K)?
Multiply Cv in J/(mol·K) by 1000 and divide by molar mass in g/mol: Cv,mass = Cv × 1000/M. The factor 1000 converts grams to kilograms in the denominator.

Related

Formula used
in cp | Molar heat capacity at constant pressure Cp | J/(mol·K) | 29.100 | 0
in mm | Molar mass | g/mol | 28.014 | 0
out cv | Molar heat capacity at constant volume Cv | J/(mol·K) | cp - 8.31446261815324 | 3
out gamma | Heat-capacity ratio γ = Cp/Cv | - | cp / cv | 4
out cvmass | Mass-specific Cv | J/(kg·K) | cv * 1000 / mm | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →