molecalculator

Moles & Molar Mass

Density of Benzene in lb/gal

Calculator No. 01-10533 · Updated · Formula and assumptions shown below

Density in lb/gal (US) 7.315 lb/gal
Density in kg/m³
876.5 kg/m³
= Density in g÷cm³ × 1000
Density in g/cm³
0.8765 g/cm³
Set in the form below
Temperature
20 °C
Set in the form below
You enter
Density in g/cm³ (g/cm³), Temperature (°C)
You get
Density in lb/gal (US) (lb/gal), Density in kg/m³ (kg/m³)
Rounding
3 dp · 1 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The density of benzene is approximately 7.32 lb/gal at 20 °C (68 °F). This value is derived from benzene’s standard density of 0.8765 g/cm³, converted to U.S. liquid gallons.

Formula

The conversion from density in g/cm³ to lb/gal uses the relationship: 1 g/cm³ = 8.345404 lb/gal (U.S. liquid gallon). The formula is:

Density (lb/gal) = Density (g/cm³) × 8.345404

Where:

  • Density (g/cm³) is the mass of benzene per unit volume in grams per cubic centimeter.
  • 8.345404 is the conversion factor: 1 g/cm³ = 8.345404 lb/gal (since 1 lb = 453.59237 g and 1 gal = 3785.411784 cm³).

For benzene at 20 °C, plugging in 0.8765 g/cm³ gives 0.8765 × 8.345404 = 7.315 lb/gal, usually rounded to 7.32 lb/gal.

Worked Example

Using the default values from the calculator: density = 0.8765 g/cm³, temperature = 20 °C.

  1. Start with the density: 0.8765 g/cm³.
  2. Multiply by the conversion factor: 0.8765 × 8.345404 = 7.3153 lb/gal.
  3. Round to three decimal places: 7.315 lb/gal.

The calculator also gives the density in kg/m³: 0.8765 × 1000 = 876.5 kg/m³.

Assumptions

  • The density of benzene is temperature-dependent; the default 0.8765 g/cm³ is for 20 °C (68 °F). At other temperatures, use the appropriate density value.
  • The conversion assumes U.S. liquid gallons, not imperial gallons (1 imperial gal = 1.20095 U.S. gal).
  • Benzene is a pure liquid; the density of mixtures or solutions will differ.

Why Benzene’s Density Matters

Benzene (C₆H₆) is a colorless, flammable liquid with a sweet odor. Its density is a key physical property used in:

  • Storage and transport: Tanks and containers are rated by weight, so knowing lb/gal helps calculate total mass for a given volume.
  • Mixing and dilution: When preparing solutions, density converts between mass and volume.
  • Safety and spill response: Benzene is less dense than water (water is 8.34 lb/gal), so it floats on water, affecting containment strategies.
  • Quality control: Density is a quick check for purity; deviations indicate contamination.

How Temperature Affects the Density

Like most liquids, benzene expands when heated, so its density decreases with rising temperature. At 20 °C, density is 0.8765 g/cm³ (7.32 lb/gal). At 25 °C, it drops to about 0.8737 g/cm³ (7.29 lb/gal). At 40 °C, it is roughly 0.857 g/cm³ (7.15 lb/gal). If you need an exact value, consult a reference table for the specific temperature.

Common Mistakes and Misconceptions

  • Using imperial gallons: The conversion factor 8.345404 is for U.S. gallons. If you use imperial gallons, the factor becomes 10.0224, giving a much higher number (about 8.78 lb/gal). Always confirm which gallon is intended.
  • Confusing g/cm³ with kg/m³: 1 g/cm³ = 1000 kg/m³, so benzene is 876.5 kg/m³, not 0.8765 kg/m³.
  • Assuming density is constant: Density changes with temperature; using a 20 °C value for a 60 °C process introduces error.
  • Rounding too early: If you round 0.8765 to 0.88, the lb/gal result becomes 7.34, a difference of 0.02 lb/gal. For large volumes, this adds up.

Comparing Benzene to Other Liquids

Benzene is lighter than water (7.32 vs. 8.34 lb/gal), but heavier than many common hydrocarbons:

  • Gasoline: ~6.0–6.5 lb/gal (varies by blend)
  • Toluene: ~7.19 lb/gal (0.862 g/cm³)
  • Ethanol: ~6.58 lb/gal (0.789 g/cm³)
  • Water: 8.34 lb/gal (1.00 g/cm³)
  • Carbon tetrachloride: ~13.5 lb/gal (1.594 g/cm³)

This comparison helps in separation processes: benzene forms a separate layer on top of water, but below heavier chlorinated solvents.

Safety and Handling Considerations

Benzene is a known carcinogen; exposure must be minimized. When handling benzene, always use appropriate personal protective equipment (gloves, goggles, lab coat) and work in a fume hood. It is highly flammable (flash point -11 °C), so keep away from ignition sources. For spills, because benzene floats on water, use absorbent materials designed for hydrocarbons. Always follow your lab method, the safety data sheet (SDS) and your supervisor. Density values are for planning; actual measurement with a hydrometer or pycnometer is recommended for critical applications.

Frequently Asked Questions

Is benzene heavier than water?

No. Benzene has a density of about 7.32 lb/gal, while water is about 8.34 lb/gal. Benzene is less dense than water, so it floats on water. This is why benzene spills on water form a separate layer on top.

How do I convert benzene density from g/cm³ to lb/gal?

Multiply the density in g/cm³ by 8.345404. For example, 0.8765 g/cm³ × 8.345404 = 7.315 lb/gal. This conversion factor is specific to U.S. liquid gallons.

What is the density of benzene at 25 °C?

At 25 °C, benzene has a density of approximately 0.8737 g/cm³, which equals about 7.29 lb/gal. The density decreases slightly as temperature increases.

Why is benzene’s density lower than water’s?

Benzene molecules (C₆H₆) are nonpolar and have weak intermolecular forces (London dispersion), so they pack less efficiently and have a lower mass per volume than water, which has strong hydrogen bonding that pulls molecules closer together despite being a smaller molecule.

Does the density of benzene affect its boiling point?

Not directly. Boiling point depends on intermolecular forces, not density. Benzene boils at 80.1 °C. Density is a separate physical property, though both are influenced by molecular mass and structure.

Can I use this calculator for other liquids?

Yes, the calculator works for any liquid if you enter its density in g/cm³. The conversion factor is universal for converting g/cm³ to lb/gal. Just replace the default density with the value for your liquid.

Related

Formula used
in d | Density in g/cm³ | g/cm³ | 0.8765 | 0 | 1.5
in t | Temperature | °C | 20 | -273.15 | 100
out lbgal | Density in lb/gal (US) | lb/gal | d * 8.345404 | 3
out kgm3 | Density in kg/m³ | kg/m³ | d * 1000 | 1

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →