molecalculator

Moles & Molar Mass

Nitric Acid Density: Values by Concentration

Calculator No. 01-3588 · Updated · Formula and assumptions shown below

Estimated nitric acid density 1.404 g/mL
Estimated density
1,404 kg/m^3
= Estimated nitric acid density × 1000
Nitric acid concentration
68 % by mass
Set in the form below
Lower reference concentration
60 % by mass
Set in the form below
You enter
Nitric acid concentration (% by mass), Lower reference concentration (% by mass), Density at lower reference (g/mL), Upper reference concentration (% by mass), Density at upper reference (g/mL)
You get
Estimated nitric acid density (g/mL), Estimated density (kg/m^3)
Rounding
3 dp · 0 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Nitric acid does not have one fixed density: the value depends mainly on its concentration and temperature. As a practical reference, concentrated commercial nitric acid at about 68–70% by mass has a density near 1.41 g/mL at 20 °C; this calculator estimates density by linear interpolation between supplied concentration-and-density data points.

Formula

The calculator uses straight-line interpolation between two reference data points:

ρ = ρ₁ + (w − w₁)(ρ₂ − ρ₁)/(w₂ − w₁)

  • ρ is estimated solution density in g/mL.
  • w is nitric acid concentration in percent by mass.
  • w₁ and w₂ are the lower and upper reference concentrations, in percent by mass.
  • ρ₁ and ρ₂ are the corresponding reference densities in g/mL.

The second output converts g/mL to kg/m³. Since 1 g/mL equals 1,000 kg/m³, the conversion is ρ (kg/m³) = ρ (g/mL) × 1,000. The interpolation is only valid between the two reference concentrations, and the entered data must come from a compatible, reliable source at the temperature of interest.

Worked Example

Using the defaults, the target solution is 68% nitric acid by mass. The lower reference is 60% at 1.37 g/mL, and the upper reference is 70% at 1.413 g/mL.

ρ = 1.37 + (68 − 60)(1.413 − 1.37)/(70 − 60)
ρ = 1.37 + (8)(0.043)/10
ρ = 1.37 + 0.0344 = 1.4044 g/mL
Rounded to three decimal places: 1.404 g/mL.

In kg/m³: 1.4044 × 1,000 = 1,404.4 kg/m³, displayed as 1,404 kg/m³.

Assumptions

  • The reference concentrations and densities describe aqueous nitric acid at the same temperature.
  • Density changes linearly between the two supplied points. This is an approximation, not a general physical law.
  • The calculator does not correct for temperature, impurities, dissolved gases, or measurement uncertainty.
  • The example values are illustrative conventional reference values; consult a reliable concentration-density table or the product’s safety data sheet for the specific solution and temperature.

What nitric acid density means

Density is mass divided by volume. A density of 1.404 g/mL means that one millilitre of the solution has a mass of about 1.404 grams under the stated conditions. It does not mean that the liquid is pure nitric acid: commercial concentrated acid is an aqueous mixture, and its density reflects both nitric acid and water.

Concentration is commonly given as mass percent, sometimes written wt% or % w/w. A 68% by-mass solution contains 68 g of nitric acid in every 100 g of solution; the remaining mass is mostly water. This is different from volume percent and from molarity. Never treat these concentration measures as interchangeable without the relevant density and composition information.

How concentration and temperature affect it

For many aqueous nitric acid mixtures, density rises as the acid concentration increases over the commonly encountered commercial range. The relation is not perfectly linear across the full concentration range, which is why a single rule of thumb should not be used to convert every concentration into a density.

Temperature matters because liquids expand or contract as they warm or cool. For a fixed mass, a larger volume means a lower density. Thus, a value quoted at 20 °C should not be assumed exact at a different temperature. Tables may use 15 °C, 20 °C, or another reference temperature; compare values only when the temperature basis is clear.

Density data are also useful for checking a stated concentration, estimating mass from a measured volume, or converting between mass-based and volume-based quantities. Those applications require suitable, temperature-matched data and appropriate measurement uncertainty.

Common values and how to use them

Concentrated reagent-grade nitric acid is often sold around 68–70% by mass, with a density roughly 1.41 g/mL near room temperature. Exact specifications vary by product and temperature. More dilute solutions generally have lower densities, but the precise value should be taken from a table for the exact concentration rather than inferred from the concentrated-acid figure.

  • For a quick description, state the concentration basis and temperature alongside the density.
  • For a product-specific value, use its certificate or safety data sheet, checking that the stated units and temperature match your intended use.
  • For calculations requiring precision, use a published concentration-density table or a validated measurement rather than broad interpolation.
  • Do not infer concentration from density alone if temperature, impurities, or the identity of the solution are uncertain.

Remember that g/mL and kg/m³ differ by a factor of 1,000, while g/cm³ has the same numerical value as g/mL. A frequent mistake is to report 1.41 g/mL as 1.41 kg/m³; the correct conversion is approximately 1,410 kg/m³.

Limits and safety

This calculator is a simple interpolation aid, not a chemical assay or a replacement for a reference table. Its output inherits the accuracy of the two input points. It can give misleading results if the points were measured at different temperatures, use different concentration definitions, or lie far apart on a curved part of the concentration-density relationship. The equation also does not validate the input data or identify the acid.

Nitric acid is corrosive and can cause severe burns; concentrated acid is also a strong oxidizer. Density information alone does not make handling safe. For any bench work, follow your lab method, the safety data sheet (SDS) and your supervisor. Use appropriate facilities and protective measures specified by the relevant safety documentation; do not use this calculator as handling or dilution instructions.

Frequently Asked Questions

What is the density of concentrated nitric acid?
Commercial concentrated nitric acid around 68–70% by mass is approximately 1.41 g/mL near 20 °C. Check the product’s documentation for its exact concentration and temperature-specific value.

Is nitric acid density always 1.41 g/mL?
No. Density changes with concentration and temperature. The figure near 1.41 g/mL is a useful approximate value for common concentrated aqueous acid, not a universal value for every nitric acid solution.

What is the density of 68% nitric acid?
A representative value near 20 °C is about 1.40 g/mL. The example interpolation here gives 1.404 g/mL from its stated reference points; use a suitable published table or product data for a more authoritative value.

How do I convert nitric acid density from g/mL to kg/m³?
Multiply by 1,000. For example, 1.404 g/mL is 1,404 kg/m³.

Does warming nitric acid change its density?
Yes. Temperature changes the solution’s volume and therefore its density. A density value is meaningful only when its reference temperature is known.

Related

Formula used
in x | Nitric acid concentration | % by mass | 68 | 0 | 100
in x1 | Lower reference concentration | % by mass | 60 | 0 | 100
in d1 | Density at lower reference | g/mL | 1.37 | 0.001
in x2 | Upper reference concentration | % by mass | 70 | 0 | 100
in d2 | Density at upper reference | g/mL | 1.413 | 0.001
out d | Estimated nitric acid density | g/mL | d1 + (x - x1) * (d2 - d1) / (x2 - x1) | 3
out kg | Estimated density | kg/m^3 | d * 1000 | 0

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →