This calculator estimates sulfuric acid solution density from the acid’s mass fraction and temperature, using a representative reference value for concentrated acid. Enter the sulfuric acid concentration by mass and temperature to get an estimated density in g/mL and kg/m³; actual density depends on the exact solution composition and conditions.
Formula
The calculator uses an approximate correction around a reference solution:
ρ = ρ98,20 × [1 + 0.0007 × (98 − w)] ÷ [1 + 0.0005 × (t − 20)]
- ρ is estimated solution density in g/mL.
- ρ98,20 is the reference density of 98% sulfuric acid at 20 °C, entered as 1.836 g/mL.
- w is sulfuric acid mass fraction expressed as a percentage, such as 98 for 98% by mass.
- t is solution temperature in °C.
- 0.0007 and 0.0005 are approximate local correction coefficients per percentage point and per °C. They are not universal material constants.
The SI conversion is density in kg/m³ = density in g/mL × 1000, because 1 g/mL equals 1000 kg/m³. The correction equation is a simple estimate near the reference point, not a substitute for a concentration–density table or direct measurement.
Worked Example
Using the calculator’s default values, w = 98%, t = 20 °C, and ρ98,20 = 1.836 g/mL:
- Concentration correction: 1 + 0.0007 × (98 − 98) = 1.00000.
- Temperature correction: 1 + 0.0005 × (20 − 20) = 1.00000.
- Density: ρ = 1.836 × 1.00000 ÷ 1.00000 = 1.8360 g/mL.
- SI form: 1.8360 × 1000 = 1836 kg/m³.
Assumptions
- The concentration is mass percent of H₂SO₄ in the final solution, not volume percent.
- The reference value applies to approximately 98% sulfuric acid at 20 °C; real reference values vary slightly by source and material specification.
- The correction factors are approximate and intended for orientation near concentrated aqueous acid, not precise laboratory or industrial calculations.
- The solution is treated as a homogeneous sulfuric acid–water mixture without other dissolved substances.
What sulfuric acid density means
Density is mass divided by volume. It tells you how much a given volume of a material weighs, but it does not by itself tell you how much sulfuric acid is present. For an aqueous solution, density changes with both the proportion of acid and the temperature. A bottle labeled 98% sulfuric acid means 98% of its mass is H₂SO₄; it does not mean 98% of its volume is acid.
Concentrated sulfuric acid is notably dense: a commonly used reference is about 1.84 g/mL near room temperature for roughly 98% acid. Water at room temperature is close to 1.00 g/mL, so the same volume of concentrated acid has substantially greater mass. The exact figure should be tied to a stated temperature and concentration rather than treated as a fixed property of every sulfuric acid solution.
Why concentration and temperature matter
Mixing sulfuric acid with water changes the liquid’s composition and volume; volume is not simply the sum of the starting volumes. As a result, density cannot be reliably calculated by averaging the densities of pure water and pure acid. Reliable values are normally obtained from measured data for the particular concentration and temperature.
Temperature also affects density because liquids generally expand as they warm. The same solution therefore occupies a slightly larger volume at a higher temperature while its mass remains unchanged, reducing its density. The calculator applies an approximate temperature adjustment, but its linear form should not be extrapolated broadly or used where high precision matters.
Using density for mass and volume conversions
For a known sample density, the basic relationships are mass = density × volume and volume = mass ÷ density. Keep units consistent. For example, using 1.836 g/mL, 10.0 mL corresponds to an estimated mass of 18.36 g. This is a mass estimate for the whole solution, not 18.36 g of pure H₂SO₄ unless the sample is 100% acid.
To estimate the H₂SO₄ mass in a solution, multiply the solution mass by its mass fraction. A 98% by-mass sample weighing 18.36 g contains approximately 0.98 × 18.36 = 17.99 g H₂SO₄. These calculations assume the concentration label is accurate and that the sample is representative and uncontaminated. For accurate solution preparation or analysis, use the concentration and density specification supplied for the actual material.
Limits, measurement, and safety
The calculator’s output is an estimate produced by a deliberately simple local correction. It is most defensible near its reference concentration and temperature. It does not reproduce a full density table, account for impurities, or determine concentration from density. In particular, do not infer an exact acid percentage from an approximate density unless you use a validated table or analytical method for the relevant temperature.
Density measurements can be affected by temperature control, trapped air, evaporation, contamination, and glassware or instrument calibration. If density is being used for a specification, process calculation, or quantitative laboratory work, consult a recognized reference table or measure the sample using an appropriate calibrated method at a controlled temperature.
Sulfuric acid is highly corrosive and can cause severe burns; dilution releases substantial heat. Never treat density calculations as instructions for handling or mixing acid. Follow the relevant safety data sheet (SDS), approved laboratory procedures, and supervisor guidance; use appropriate protective equipment and facilities for any authorized bench work.
Frequently Asked Questions
What is the density of concentrated sulfuric acid?
Approximately 1.84 g/mL near 20 °C for sulfuric acid around 98% by mass is a widely used reference. Check the product specification for its exact concentration and reference temperature.
Is sulfuric acid denser than water?
Yes. Concentrated sulfuric acid is roughly 1.84 times as dense as water near room temperature, although more dilute acid solutions have different densities.
Does sulfuric acid density change with temperature?
Yes. Warming generally lowers the density of a liquid solution, while cooling raises it. Comparisons are meaningful only when concentration and temperature are stated.
Can density tell me the concentration of sulfuric acid?
It can help estimate concentration when compared with a reliable density–concentration table at a known temperature. Density alone is not enough for an exact result, especially when impurities or temperature uncertainty are present.
What is 1.84 g/mL in kg/m³?
It is 1840 kg/m³, using the exact unit conversion 1 g/mL = 1000 kg/m³.
Related
Formula used
in w | Sulfuric acid mass fraction | % | 98 | 0 | 100 in t | Temperature | °C | 20 | 0 | 100 in d98 | Density of 98% acid at 20 °C | g/mL | 1.836 | 0.001 out rho | Estimated density | g/mL | d98 * (1 + 0.0007 * (98 - w)) / (1 + 0.0005 * (t - 20)) | 4 out rho_si | Estimated density | kg/m³ | rho * 1000 | 0
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Skip Calculator for Soil: What It Can and Can’t Do7.500 m³
- USD to KPW Calculator: Convert Dollars to North Korean Won90,000.00 KPW
- OK Calculator on TV on the Radio? Meaning Explained
- Pension Calculator KP: Estimate Your Pension Benefits
- Neonatal Kp Calculator: What It Means80.0000 mmol/mmol
- Newton to kp Converter Calculator and Formula1.0000 kp