molecalculator

Moles & Molar Mass

Dilution Equation c1v1 c2v2: How to Use It

Calculator No. 01-7971 · Updated · Formula and assumptions shown below

Molarity 0.2000 mol/L
Concentration in millimolar
200.00 mM
= Molarity × 1000
Mass of solute
2.922 g
Set in the form below
Molar mass
58.44 g/mol
Set in the form below
You enter
Mass of solute (g), Molar mass (g/mol), Final solution volume (mL)
You get
Molarity (mol/L), Concentration in millimolar (mM)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The dilution equation c₁V₁ = c₂V₂ calculates the volume of a concentrated stock solution needed to prepare a more dilute solution, or the concentration that results from diluting a known volume. You enter three of the four values (initial concentration, initial volume, final concentration, final volume) and the calculator solves for the missing one.

Formula

The dilution equation is written as:

c₁V₁ = c₂V₂

where:

  • c₁ = concentration of the stock (initial) solution, in mol/L (M)
  • V₁ = volume of the stock solution taken, in L or mL
  • c₂ = concentration of the final (diluted) solution, in mol/L
  • V₂ = final total volume after dilution, in L or mL

The key requirement is that c₁V₁ equals the amount of solute (in moles) transferred, and c₂V₂ is the same amount of solute after adding solvent. The volumes on both sides must be in the same unit (both L or both mL).

Worked Example

Using the calculator defaults: you weigh out 2.922 g of sodium chloride (NaCl, molar mass = 58.44 g/mol) and dissolve it to a final volume of 250 mL. The molarity is:

  1. Moles of NaCl = 2.922 g ÷ 58.44 g/mol = 0.05000 mol
  2. Volume in liters = 250 mL ÷ 1000 = 0.250 L
  3. Molarity = 0.05000 mol ÷ 0.250 L = 0.2000 mol/L
  4. In millimolar: 0.2000 × 1000 = 200.0 mM

The calculator shows the same result: c = 0.2000 mol/L and cmm = 200.0 mM.

Assumptions

  • The solute is pure and fully dissolves without chemical reaction.
  • The final volume is measured after adding solvent to the mark (not the volume of solvent added).
  • The solution is dilute enough that volumes are additive (no significant contraction or expansion).
  • Temperature is constant; molarity changes slightly with temperature because volume changes.

How to Choose Which Variable to Solve For

You can rearrange the equation to solve for any of the four variables:

  • Find V₁ (volume of stock needed): V₁ = (c₂V₂) ÷ c₁
  • Find c₁ (stock concentration): c₁ = (c₂V₂) ÷ V₁
  • Find c₂ (final concentration): c₂ = (c₁V₁) ÷ V₂
  • Find V₂ (final volume after dilution): V₂ = (c₁V₁) ÷ c₂

In the lab, the most common use is preparing a dilute solution from a concentrated stock. For example, you have a 5.0 M NaCl stock and need 500 mL of 0.25 M NaCl. Using V₁ = (0.25 × 500) ÷ 5.0 = 25 mL. You would pipette 25 mL of stock into a 500 mL volumetric flask and add water to the mark.

Common Mistakes and Misconceptions

The most frequent error is using different volume units on the two sides. If c₁ is in mol/L and V₁ is in mL, then c₂V₂ must also use mL; the equation works as long as both volumes share the same unit. Do not mix L and mL without converting.

Another misconception is that the equation works for serial dilutions where you take a portion of the diluted solution and dilute it again. It does, but you must apply it step by step: each step uses the concentration of the previous solution as c₁. For a single dilution, c₁ is always the stock concentration, not the concentration after adding solvent.

Also, remember that V₂ is the final total volume, not the volume of solvent added. If you add 100 mL of water to 100 mL of stock, the final volume is often close to 200 mL but not exactly—mixing can cause slight volume changes. Always use a volumetric flask to make the final volume exact.

When to Use c₁V₁ = c₂V₂ (and When Not)

Use this equation when you are diluting a solution with solvent, keeping the amount of solute constant. It applies to:

  • Preparing working solutions from concentrated stock solutions (e.g., buffers, media, reagents)
  • Diluting an acid or base to a desired molarity
  • Calculating the concentration after adding more solvent to a known volume

Do not use it when:

  • You are mixing two different solutions with different solutes (that requires a mass balance for each solute).
  • The solute reacts with the solvent or decomposes (e.g., some enzymes lose activity over time).
  • You need to account for density changes (e.g., concentrated sulfuric acid dilution generates heat and changes volume).

For those cases, use mass-based calculations or measure the final volume directly.

Relation to Molarity and Mass

The dilution equation is derived from the definition of molarity: c = n/V, where n is moles of solute. Rearranging gives n = cV. Since dilution does not change n, c₁V₁ = c₂V₂. To prepare a solution from a solid, you first calculate the mass needed using molar mass: mass = moles × molar mass. The calculator above does this in one step: it takes mass, molar mass, and final volume to give molarity. That is the reverse of dilution—here you are starting from a solid, not a stock solution.

Frequently Asked Questions

What does c₁V₁ = c₂V₂ stand for?

It stands for initial concentration times initial volume equals final concentration times final volume. It expresses the conservation of moles: the amount of solute you take from the stock is the same amount present in the diluted solution.

Can I use mL on both sides without converting to L?

Yes, as long as both V₁ and V₂ are in the same unit (both mL or both L). The equation is a ratio, so the volume unit cancels out. However, when you plug the result into molarity calculations, convert to liters because molarity is defined as moles per liter.

What if I add solvent to a solid solute—does c₁V₁ = c₂V₂ apply?

No. That equation applies only when you start with a solution of known concentration. If you start with a solid, you need to calculate moles from mass and molar mass, then divide by the final volume to get molarity. That is what the calculator above does.

How do I do a serial dilution using this equation?

Apply the equation step by step. For each step, the concentration of the solution you are diluting becomes c₁, and the new final volume and concentration become V₂ and c₂. For example, to make a 1:10 dilution, mix 1 part stock with 9 parts solvent; the resulting concentration is c₁/10. Repeat as needed.

Does temperature affect the dilution equation?

Yes, slightly. Molarity depends on volume, and volume changes with temperature. However, for most lab work at room temperature, the effect is negligible. If you need high precision, prepare solutions at the temperature stated on the volumetric flask (usually 20 °C or 25 °C).

Why is my calculated concentration different from the label on the bottle?

The label may give the concentration of the solute as a percentage (w/v or w/w), not molarity. You must convert percent to molarity using the solute’s molar mass and the solution density. Also, some commercial reagents are not 100% pure; check the certificate of analysis for the exact purity.

Related

Formula used
in m | Mass of solute | g | 2.922 | 0
in mm | Molar mass | g/mol | 58.44 | 0.001
in v | Final solution volume | mL | 250 | 0.001
out c | Molarity | mol/L | m / mm / (v / 1000) | 4
out cmm | Concentration in millimolar | mM | c * 1000 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →