The DNA purity 260/230 ratio is the absorbance at 260 nm divided by the absorbance at 230 nm, measured by a UV spectrophotometer. This calculator works out that ratio from the two absorbance readings you enter; the result is dimensionless and helps flag possible contaminants, but it does not by itself prove that DNA is pure or usable.
Formula
Divide the absorbance at 260 nanometers by the absorbance at 230 nanometers:
260/230 ratio = A260 ÷ A230
- A260 is the measured absorbance at 260 nm, in absorbance units (AU).
- A230 is the measured absorbance at 230 nm, in AU.
- 260/230 ratio is a unitless quotient. Because both readings use the same units, those units cancel.
Enter nonnegative readings from the same sample measurement and blanking setup. A230 must be greater than zero for the division to produce a defined result. A reading of zero at 230 nm makes the ratio undefined; a very small reading can make it extremely sensitive to measurement noise. The calculator reports the arithmetic ratio only. It cannot assess the instrument’s detection limits or decide whether a sample is fit for a particular experiment.
Worked Example
Using the defaults in the calculator:
- A260 = 0.8 AU.
- A230 = 0.4 AU.
- 260/230 ratio = 0.8 AU ÷ 0.4 AU = 2.00.
The ratio is 2.00, with no units. This calculation is a simple quotient; it does not establish that the sample contains only DNA.
Assumptions
- Both absorbance values come from the same sample and compatible measurement conditions.
- Absorbance is entered as a nonnegative number in AU, without mixing blank-corrected and uncorrected readings.
- The 230 nm reading is above zero. The calculator does not model measurement uncertainty or instrument-specific limits.
What the Ratio Indicates
Nucleic acids absorb UV light strongly near 260 nm. The 230 nm reading can reflect absorption from several substances that may remain after extraction, including salts, some organic compounds, and reagents used in purification. The ratio compares these signals; it is therefore a screening indicator for contamination rather than a direct measurement of DNA concentration or a chemical identification test.
For relatively clean DNA measured under suitable conditions, a 260/230 ratio around 2.0 to 2.2 is often used as a reference range. This is a guideline, not a universal pass/fail threshold. RNA is also a nucleic acid and has similar UV-based purity considerations. Sample composition, concentration, pH, measurement method, blank choice, and residual extraction materials can all affect the result.
For example, a ratio of 1.3 may prompt a check for carryover from extraction or wash solutions, but it does not identify which substance is present. A ratio of 2.1 is consistent with a commonly expected range, yet does not rule out protein, RNA, genomic carryover, or other issues that the ratio cannot detect.
How to Interpret High and Low Results
- Near 2.0–2.2: Often consistent with a relatively low contribution from 230 nm-absorbing contaminants under the measurement conditions. It is not proof of purity.
- Substantially below about 2.0: May indicate residual contaminants that absorb around 230 nm, or a measurement or blanking issue. Consider the sample’s extraction method and the instrument’s guidance.
- Unusually high: Can result when A230 is very small, making the quotient unstable. It may also reflect low signal, blank mismatch, or other measurement conditions rather than exceptional purity.
Ratios become especially hard to interpret when absorbance values are close to the instrument’s reliable measurement range. If both readings are very low, small errors in either can substantially change their quotient. Report the individual readings alongside the ratio when making decisions, and use the measurement method’s quality guidance.
260/230 Compared with 260/280
The 260/230 and 260/280 ratios use different wavelengths and are sensitive to different potential sources of interference. A 260/280 ratio is often used as a rough indicator of protein or phenolic contamination; values around 1.8 for DNA and around 2.0 for RNA are common reference points, not universal acceptance limits. The 260/230 ratio more often flags contributions from substances absorbing near 230 nm, such as some salts or extraction reagents.
These measurements complement one another but do not replace a concentration or integrity check. A sample can show an acceptable 260/230 ratio and still be degraded, contain RNA, or have an inaccurate concentration estimate. Conversely, a low ratio may not prevent every downstream application; the acceptable quality depends on the method and its tolerance for contaminants.
Common Problems and Better Checks
A frequent misconception is that a ratio close to 2.0 proves the DNA is pure. The ratio is only one comparison of two absorbance readings; it cannot identify contaminants or measure DNA integrity. It should be interpreted together with the absolute absorbance values, the 260/280 ratio, and the purpose of the sample.
- Check the blank: Use a blank that matches the sample’s measurement solution. A mismatch can distort the baseline and the ratio.
- Check both readings: A plausible quotient can hide weak or noisy signals. Do not assess the ratio without considering A260 and A230 individually.
- Confirm the sample type: DNA, RNA, mixtures, and different buffer conditions may have different interpretation needs.
- Use an appropriate follow-up: A fluorescence-based concentration assay can provide a more selective nucleic-acid concentration estimate. Gel electrophoresis or another suitable integrity method can help assess fragmentation; neither is replaced by a purity ratio.
If a result is unexpected, first review the blank, signal strength, and measurement conditions. Whether to repeat a measurement or further clean a sample depends on the protocol and intended downstream use. For bench work, follow your lab method, the safety data sheet (SDS) and your supervisor.
Frequently Asked Questions
What is a good DNA 260/230 ratio?
A value around 2.0–2.2 is a commonly cited reference for relatively clean DNA, but it is not a universal cutoff. Interpret it with the readings, sample type, measurement conditions, and downstream requirements.
What does a low 260/230 ratio mean?
It can indicate substances contributing absorbance near 230 nm, including some salts or extraction reagents. It can also reflect blanking or measurement problems, so the ratio alone cannot diagnose the cause.
Can a DNA 260/230 ratio be too high?
Yes. A high ratio can occur when A230 is close to zero, making the division unstable. Check the absolute readings and measurement quality before treating it as evidence of exceptional purity.
Is 260/230 the same as 260/280?
No. They compare absorbance at different wavelengths and are used as complementary screening indicators. Neither ratio alone confirms purity, concentration, or DNA integrity.
Does a good ratio mean my DNA concentration is accurate?
No. The ratio describes the relationship between two absorbance readings, not DNA concentration accuracy. Low-concentration samples and interfering substances can affect UV-based estimates; use a suitable concentration method for the application.
Related
Formula used
in a260 | Absorbance at 260 nm | AU | 0.8 | 0 in a230 | Absorbance at 230 nm | AU | 0.4 | 0 out r | DNA purity 260/230 ratio | - | a260 / a230 | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Isotope Percent Abundance Calculator and How to Use It75.91 %
- Percentage Abundance Calculator and How to Find It
- Isotope Fractional Abundance Calculator and Formula0.2409 fraction
- Percent Abundance Formula: Calculate Isotope Percentages25.00 %
- Isotope Percent Abundance Calculator and How to Use It50.00 %
- Isotope Percent Abundance Calculator and How-To Guide75.91 %