molecalculator

Moles & Molar Mass

DNA Purity 260/280 Ratio: What the Number Means

Calculator No. 01-3558 · Updated · Formula and assumptions shown below

DNA 260/280 purity ratio 1.80 ratio
Absorbance at 260 nm
1.8 AU
Set in the form below
Absorbance at 280 nm
1 AU
Set in the form below
You enter
Absorbance at 260 nm (AU), Absorbance at 280 nm (AU)
You get
DNA 260/280 purity ratio (ratio)
Rounding
2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The DNA purity 260/280 ratio is the absorbance at 260 nm divided by the absorbance at 280 nm; for relatively pure DNA, a value near 1.8 is commonly expected. This calculator divides your measured A260 by A280 and reports the ratio, which is a screening indicator—not a definitive test of DNA quality or suitability.

Formula

260/280 ratio = A260 ÷ A280. A260 is the sample’s absorbance at a wavelength of 260 nanometres, and A280 is its absorbance at 280 nanometres. Absorbance (AU, or absorbance units) is dimensionless, so the quotient is also dimensionless. Enter measurements from the same sample, using the same blank and measurement conditions. A280 must be greater than zero because division by zero is undefined.

Worked Example

Using the calculator’s default values:

  1. A260 = 1.8 AU and A280 = 1.0 AU.
  2. Ratio = 1.8 AU ÷ 1.0 AU.
  3. 260/280 ratio = 1.80.

The result is the ratio only; it does not calculate DNA concentration or prove that the sample is free of contaminants.

Assumptions

  • Both readings are valid absorbance measurements for the same sample and blank.
  • The A280 input is positive.
  • The value is used as a screening measure, interpreted alongside sample type and other quality checks.

What the Ratio Measures

Nucleic acids absorb ultraviolet light strongly around 260 nm. Proteins, especially those containing aromatic amino acids, absorb more strongly around 280 nm. Comparing absorbance at these wavelengths gives a quick indication of whether a nucleic-acid preparation may contain protein or other UV-absorbing material.

For purified DNA, approximately 1.8 is a commonly cited reference value. For purified RNA, a value around 2.0 is commonly expected. These are conventions, not sharp pass-or-fail boundaries. The result can vary with the DNA’s composition, pH, ionic strength, concentration, measurement method and contaminants. A ratio close to the reference is reassuring, but it cannot establish identity, integrity, concentration accuracy or suitability for every experiment.

The ratio is also not a percentage. A reading of 1.8 does not mean “180% pure,” and it does not mean that 10% of the sample is protein. It is simply the quotient of two absorbance readings.

How to Use and Interpret the Result

Enter the A260 and A280 readings from a UV-absorbance measurement. The calculator performs the division without rounding intermediate measurements; its displayed result is rounded to two decimal places. Keep the original instrument readings, since rounding them before calculation can affect the result, especially when readings are small.

  • Near 1.8 for DNA: often consistent with relatively clean DNA, but not proof of purity.
  • Substantially below 1.8: may be associated with protein, phenol, or other substances that increase absorbance near 280 nm. It can also arise from measurement or blanking problems.
  • Above the expected range: may reflect RNA in a DNA preparation, a low or unreliable A280 reading, or other measurement and sample effects.
  • Very low readings: make the ratio unstable. Small errors in either absorbance can produce a large change when the denominator is close to zero.

These patterns are clues, not diagnoses. A ratio alone cannot identify which contaminant is present. For example, a low ratio does not establish that protein is the cause; check the measurement setup and use a method suited to the suspected contaminant.

Measurement Limits and Common Problems

Blanking is important: the blank should match the sample’s buffer or solvent as closely as the method requires. A mismatched blank, dirty measurement surface, bubbles, an unsuitable sample volume, or carryover can distort absorbance. Follow the measurement method’s instructions and check that readings fall within its validated range. If the readings are near the instrument’s lower limit, the ratio may be particularly unreliable.

Absorbance depends on concentration and optical path length. Some instruments account for path length automatically; others require a defined cuvette path. Do not compare values from different measurement setups as if they were interchangeable without checking how the readings were obtained. Use consistent units and conditions, although the ratio itself has no units.

Contaminants do not all affect the two wavelengths in the same way. RNA can contribute to A260 and make a DNA sample appear to have a higher nucleic-acid signal. Compounds such as phenol can alter UV absorbance, while salts or buffer components may affect a measurement depending on their properties and concentration. The 260/280 ratio is not a universal detector for these substances, nor does it directly measure DNA integrity. A gel or another appropriate analytical method may be needed to assess fragmentation; a separate concentration method may be useful when absorbance readings are unreliable.

Related Ratios and Follow-Up Checks

The 260/230 ratio is another commonly used absorbance-based check. It compares A260 with A230 and can provide clues about some residual salts, organic compounds or other UV-absorbing substances. It has its own interpretation limits and should not be treated as a contaminant-identification test. Neither ratio replaces an assessment tailored to the experiment.

When a result is unexpected, check the blank and raw readings first, then consider whether the sample is too dilute, the buffer differs from the blank, or the preparation may contain RNA or another UV-absorbing substance. If the sample matters for a downstream application, assess concentration and integrity with methods appropriate to that application. For bench work, follow your lab method, the safety data sheet (SDS) and your supervisor.

Frequently Asked Questions

What is a good 260/280 ratio for DNA?
A value around 1.8 is the common reference for relatively pure DNA. It is a guide rather than a universal acceptance limit; the appropriate range depends on the sample and measurement method.

Is a 260/280 ratio of 1.6 acceptable?
It is below the commonly cited DNA reference and may indicate contamination or a measurement issue, but the ratio alone cannot tell which. Whether it is acceptable depends on the requirements of the intended analysis.

What does a high 260/280 ratio mean?
It may result from RNA in a DNA sample, a very low A280 reading, or measurement conditions that affect the readings. It does not by itself identify the cause or prove that the DNA is purer.

Does a 260/280 ratio measure DNA concentration?
No. It is a ratio of two absorbance readings. Concentration may be estimated from absorbance using a method-specific calculation, but that is a different calculation and can be inaccurate when contaminants contribute to absorbance.

Why is my 260/280 ratio unreliable?
Ratios become sensitive to measurement error when A280 is very small. A mismatched blank, low sample signal, bubbles, contamination on the measurement surface, or differences in buffer and measurement setup can also affect the result.

Related

Formula used
in a260 | Absorbance at 260 nm | AU | 1.8 | 0
in a280 | Absorbance at 280 nm | AU | 1 | 0
out ratio | DNA 260/280 purity ratio | ratio | a260 / a280 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →