molecalculator

Moles & Molar Mass

Electron Configuration of Li+

Calculator No. 01-10279 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The electron configuration of the lithium cation (Li+) is 1s2. This means the ion has two electrons, both occupying the lowest-energy 1s orbital, and it is isoelectronic with the noble gas helium.

Formula

For any ion, the number of electrons is:

Number of electrons = Z − (charge)

where:

  • Z = atomic number (number of protons) – for lithium, Z = 3.
  • charge = the ion’s net charge (e.g., +1 for Li+).

Once you know the electron count, you fill the orbitals in order of increasing energy (Aufbau principle): 1s, 2s, 2p, 3s, 3p, 4s, 3d, etc. Each s orbital holds 2 electrons, each p orbital holds 6, each d holds 10.

Worked Example

Using the default values from the calculator (Z = 3, neutral electrons = 3, charge = +1):

  1. Electrons in Li+ = 3 − 1 = 2.
  2. Fill the 1s orbital: 2 electrons → 1s2.
  3. No electrons remain for the 2s orbital.

Result: 1s2. This matches the calculator output.

Assumptions

  • The ion is in its ground state (lowest energy).
  • Standard Aufbau filling order applies (no exceptions for lithium).
  • The charge is a whole number (integer).

Why Li+ Has This Configuration

Lithium (Li) has atomic number 3, so a neutral lithium atom has 3 electrons. Its full electron configuration is 1s22s1. When lithium forms a cation, it loses its outermost electron (the 2s electron) to achieve a stable, filled-shell configuration. This leaves two electrons in the 1s orbital, giving Li+ the configuration 1s2.

This configuration is identical to that of helium (He, Z=2), which also has two electrons in 1s. Species with the same electron configuration are called isoelectronic. Li+, He, and H− are all isoelectronic with each other.

How to Write Electron Configurations for Ions

For cations (positive ions), you remove electrons from the highest occupied orbital first. For anions (negative ions), you add electrons to the next available orbital. The general steps are:

  1. Write the neutral atom’s configuration.
  2. Remove electrons for positive charge (from the outermost shell).
  3. Add electrons for negative charge (to the next available orbital).

For Li+, removing one electron from 1s22s1 gives 1s2. For a hypothetical Li2+, you would remove another electron, giving 1s1 (a hydrogen-like ion).

Common Mistakes and Misconceptions

  • Writing 2s1 instead of 1s2: Some people forget to remove the electron from the 2s orbital. Always remove the highest-energy electron first.
  • Confusing with helium: Li+ has the same configuration as He, but it has a different number of protons (3 vs. 2), so its size and properties differ.
  • Using noble-gas notation incorrectly: The noble-gas shorthand for Li+ is [He], but that can be confusing because the ion is not helium. It’s fine to use [He] as a shorthand, but remember the nucleus is lithium.

Why It Matters

Knowing the electron configuration of Li+ helps explain its chemical behavior:

  • Stability: The filled 1s shell gives Li+ a particularly stable electronic arrangement, which is why lithium readily forms a +1 ion.
  • Ionic radius: Li+ is much smaller than neutral Li because the loss of the outer electron removes the outer shell, and the remaining electrons are pulled closer to the nucleus.
  • Ionization energy: The second ionization energy of lithium is very high because removing a second electron would break the stable 1s2 core.
  • Chemistry in batteries: Li+ is the charge carrier in lithium-ion batteries. Its small size and low charge density allow it to move easily between electrodes.

Frequently Asked Questions

What is the electron configuration of Li+?

The electron configuration of Li+ is 1s2. It has two electrons total, both in the 1s orbital.

Is Li+ isoelectronic with helium?

Yes. Li+ has 2 electrons, same as neutral helium (He). They are isoelectronic, meaning they have identical electron configurations (1s2).

How many electrons does Li+ have?

Li+ has 2 electrons. Neutral lithium has 3, and losing one electron (due to the +1 charge) leaves 2.

Why does lithium lose an electron to form Li+?

Lithium loses its single 2s electron to achieve a filled 1s shell, which is a lower-energy, more stable configuration. This loss requires energy (ionization energy), but the resulting ion is stable in many chemical environments.

What is the noble gas notation for Li+?

The noble gas shorthand is [He], because Li+ has the same electron configuration as helium. However, it is not a helium atom; it has 3 protons.

Does Li+ have a full outer shell?

Yes. The 1s orbital is full with 2 electrons. Even though the principal quantum number n=1 is the lowest shell, it is completely filled, giving the ion a stable octet-like (duet) configuration.

Related

Formula used
in mm | Atomic number (Z) | - | 3 | 1
in e | Number of electrons in neutral atom | - | 3 | 1
in ch | Charge of the ion | - | 1 | -10
out n | Number of electrons in the ion | - | e - ch | 0
out conf | Electron configuration | - | "1s2" | 0

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →