molecalculator

Moles & Molar Mass

Enthalpy Change of Reaction: A-Level Chemistry

Calculator No. 01-8372 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The enthalpy change of reaction (ΔH) is the heat energy transferred during a chemical reaction at constant pressure, measured in kilojoules per mole (kJ/mol). You calculate it from bond enthalpies using ΔH = Σ(bonds broken) − Σ(bonds formed), or measure it experimentally using q = mcΔT and ΔH = −q/mol. This page gives you the exact A-level definitions, the two calculation methods, and the common traps that cost marks in exams.

Formula

The heat energy change is given by:

q = m × c × ΔT

where:

  • q = heat energy absorbed or released (J)
  • m = mass of the substance being heated or cooled (g) – usually the water in a calorimetry experiment
  • c = specific heat capacity (J/g·°C) – for water, 4.18 J/g·°C
  • ΔT = temperature change (°C or K, same size)

The enthalpy change of reaction per mole is then:

ΔH = −q / n

where n is the number of moles of the limiting reactant (the one that determines how much heat is produced). The negative sign is crucial: if the reaction releases heat (exothermic), q is positive and ΔH is negative; if it absorbs heat (endothermic), q is negative and ΔH is positive.

Worked Example

Using the default values from the calculator above:

m = 100 g water, c = 4.18 J/g·°C, ΔT = 8.5 °C, n = 0.025 mol.

Step 1 – Calculate the heat energy absorbed by the water:

q = 100 × 4.18 × 8.5 = 3553 J

Step 2 – Convert to kJ:

3553 J = 3.553 kJ

Step 3 – Divide by the moles of reactant, with a negative sign because the water gained heat (so the reaction released it):

ΔH = −3.553 / 0.025 = −142.1 kJ/mol

The calculator rounds to 1 decimal place, giving −142.1 kJ/mol. This is the enthalpy change per mole of the limiting reactant, assuming the reaction went to completion and all heat went into the water.

Assumptions

  • All heat released or absorbed by the reaction is transferred to the water – no heat loss to the surroundings.
  • The specific heat capacity of the solution is the same as pure water (4.18 J/g·°C).
  • The density of the solution is 1.00 g/mL, so 1 mL ≈ 1 g.
  • The reaction goes to completion and the limiting reactant is fully consumed.
  • The temperature change is measured accurately, with no heat gained from stirring or the thermometer.

Background: What Does ΔH Actually Mean?

At A-level, enthalpy change of reaction is defined as the heat energy change when the reaction occurs in the molar quantities shown in the balanced equation, at constant pressure. The symbol is ΔH, with the Δ meaning “change” and H standing for enthalpy (a measure of the total heat content of a system).

Exothermic reactions (combustion, neutralisation, most oxidation) release heat to the surroundings, so ΔH is negative. Endothermic reactions (thermal decomposition, photosynthesis) absorb heat, so ΔH is positive. The sign is the first thing examiners check – get it wrong and you lose the mark even if the number is right.

There are several specific types of enthalpy change you will meet:

  • Enthalpy of formation (ΔHf) – forming 1 mole of a compound from its elements in their standard states.
  • Enthalpy of combustion (ΔHc) – burning 1 mole of a substance in excess oxygen.
  • Enthalpy of neutralisation (ΔHneut) – reacting an acid with a base to form 1 mole of water.
  • Enthalpy of atomisation – forming 1 mole of gaseous atoms from the element in its standard state.
  • Lattice enthalpy – forming 1 mole of an ionic solid from its gaseous ions.

All of these are measured under standard conditions (298 K, 100 kPa, 1 mol dm⁻³ for solutions) – the “standard” symbol is ΔH°.

How to Calculate ΔH from Bond Enthalpies

The second method uses average bond enthalpies, which are the energies needed to break one mole of a specific covalent bond in the gaseous state. The formula is:

ΔH = Σ(bond enthalpies of bonds broken) − Σ(bond enthalpies of bonds formed)

Bonds broken are in the reactants (energy input, positive), bonds formed are in the products (energy output, negative). For example, for the reaction H₂ + Cl₂ → 2HCl:

  • Bonds broken: 1 H–H (436 kJ/mol) + 1 Cl–Cl (243 kJ/mol) = 679 kJ/mol
  • Bonds formed: 2 H–Cl (2 × 432 = 864 kJ/mol)
  • ΔH = 679 − 864 = −185 kJ/mol

This is an exothermic reaction because more energy is released forming new bonds than is absorbed breaking old ones. Note that bond enthalpy values are averages taken from many compounds, so the result is an estimate, not an exact value.

How to Choose: Which Method to Use

In exams, you will be told which method to use. But in general:

  • If you have experimental temperature data, use q = mcΔT then divide by moles.
  • If you have a balanced equation and a table of bond enthalpies, use the bond enthalpy method.
  • If you have enthalpy of formation values, use ΔH = ΣΔHf(products) − ΣΔHf(reactants).
  • If you have enthalpy of combustion values, use ΔH = ΣΔHc(reactants) − ΣΔHc(products) (note the swap).

The key is to always write out the balanced equation first, then count the number of each bond type on each side. Missing a coefficient is the most common error – a coefficient of 2 means two of that bond are broken or formed.

Common Problems and How to Avoid Them

Students lose marks on enthalpy change questions for a few predictable reasons:

  • Sign errors – forgetting the negative sign for exothermic reactions. Always ask: did the surroundings get hotter? If yes, ΔH is negative.
  • Unit confusion – q is in joules but ΔH is in kJ/mol. Convert q to kJ before dividing by moles (divide by 1000).
  • Wrong mass – in calorimetry, use the mass of the solution (usually water), not the mass of the reactant. If you add a solid to water, the total mass is water + solid, but for dilute solutions you can approximate with just the water.
  • Forgetting ΔT is a change – it is final temperature minus initial temperature, not the final temperature itself.
  • Using the wrong moles – divide by the moles of the limiting reactant, not the one in excess. If you have 0.050 mol of acid and 0.100 mol of base, the acid limits the reaction.
  • Bond enthalpy method: counting bonds wrong – draw the displayed formula to count each bond. For example, ethene (C₂H₄) has 4 C–H bonds and 1 C=C bond, not 2 C–H.

Another common misconception is that bond enthalpies are the same in every molecule. They are averages – the C–H bond in methane is slightly different from the C–H bond in ethane, but we use one average value for all C–H bonds. This is why the bond enthalpy method gives approximate values.

Experimental Measurement: Calorimetry in the Lab

The most common A-level experiment is measuring the enthalpy change of combustion of an alcohol. You burn a known mass of alcohol, use it to heat a known mass of water, and record the temperature rise. Then:

  1. Measure the initial temperature of the water.
  2. Burn the alcohol and stir continuously.
  3. Record the final temperature when the alcohol stops burning.
  4. Weigh the alcohol before and after to find the mass burned.
  5. Calculate moles of alcohol burned (mass / molar mass).
  6. Use q = mcΔT, then ΔH = −q / moles.

The result is always less exothermic than the theoretical value because heat is lost to the surroundings, some alcohol may not burn completely (forming soot), and the water gains heat from the flame as well as the reaction. To improve accuracy, you can insulate the calorimeter, use a lid, and stir constantly – but even then, expect a 20–30% error.

For neutralisation reactions, you mix acid and base in a polystyrene cup (a better insulator than glass) and measure the temperature rise. The same formula applies, but the mass is the total volume of solution (assuming 1 mL = 1 g).

Always follow your lab method, the safety data sheet (SDS) and your supervisor. Alcohols are flammable – keep them away from naked flames except when burning as intended.

Why ΔH Matters Beyond Exams

Enthalpy changes are not just an exam topic – they are used in industry to design safe and efficient chemical processes. For example, the Haber process for making ammonia is exothermic, so cooling the reactor shifts the equilibrium towards products (Le Chatelier’s principle). Combustion enthalpies are used to calculate the energy content of fuels, and bond enthalpies help chemists predict whether a proposed reaction is thermodynamically feasible.

In biology, the enthalpy change of respiration (glucose oxidation) is about −2800 kJ/mol, which is why food labels list energy in kilojoules. In materials science, lattice enthalpies explain why some ionic compounds are more stable than others. Understanding ΔH gives you a quantitative handle on why reactions happen and how much energy they involve.

Frequently Asked Questions

What is the difference between ΔH and q?

q is the heat energy transferred in a specific experiment (measured in joules). ΔH is the enthalpy change per mole of reaction (measured in kJ/mol). They are related by ΔH = −q/n, but ΔH is an intensive property – it does not depend on how much you react, whereas q does. If you double the amounts, q doubles but ΔH stays the same.

Why is ΔH negative for exothermic reactions?

By convention, enthalpy is the heat content of the system. In an exothermic reaction, the system loses heat to the surroundings, so its enthalpy decreases. A decrease is a negative change, hence ΔH < 0. Endothermic reactions absorb heat, increasing the system’s enthalpy, so ΔH > 0.

Do I need to know the specific heat capacity of water for the exam?

Yes, you should know it is 4.18 J/g·°C. It is usually given in the question, but you may be asked to recall it. For other substances, you will always be given the value in the question.

Why is my experimental value less exothermic than the data book value?

Heat losses to the surroundings are the main reason. Incomplete combustion (for fuels), heat absorbed by the calorimeter itself, and evaporation of the water all reduce the measured temperature rise. The data book value assumes perfect conditions with no losses, so your experimental value will be lower in magnitude (e.g., −400 kJ/mol instead of −550 kJ/mol).

Can I use bond enthalpies for reactions in solution?

Bond enthalpies are defined for gaseous molecules. For reactions in solution, you also need to account for the energy changes when bonds between ions and water molecules are broken and formed (hydration enthalpy). Using only covalent bond enthalpies would ignore these, so it is not accurate for ionic reactions in water. Stick to the calorimetry method for solution reactions.

What is Hess’s law and how does it relate to ΔH?

Hess’s law states that the enthalpy change of a reaction is the same whether it happens in one step or several. This is because enthalpy is a state function – it only depends on the initial and final states, not the route. You can use Hess cycles to calculate ΔH for reactions that are difficult to measure directly, such as the enthalpy of formation of an unstable compound, by combining known enthalpies of formation or combustion.

Related

Formula used
in m | Mass of water | g | 100 | 0.001
in c | Specific heat capacity of water | J/g·°C | 4.18 | 0.001
in dt | Temperature change | °C | 8.5 | -273.15
in n | Moles of limiting reactant | mol | 0.025 | 0.000001
out q | Heat energy absorbed | J | m * c * dt | 1
out dH | Enthalpy change of reaction | kJ/mol | -q / 1000 / n | 1

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →