An enthalpy of vaporization calculator estimates the molar energy needed to convert a liquid to vapor, or calculates that energy from a measured heat transfer. Enter the heat supplied and the amount of substance to find molar enthalpy in J/mol; the result applies to the stated phase-change conditions.
Formula
For a sample that is vaporized at constant pressure, molar enthalpy of vaporization is the heat transferred divided by the amount of substance:
ΔHvap = q / n
- ΔHvap is molar enthalpy of vaporization, in J/mol. The calculator’s first result converts this to kJ/mol by dividing by 1000.
- q is heat transferred to the sample during vaporization, in joules (J).
- n is the amount vaporized, in moles (mol).
The heat-per-mole conversion is therefore ΔHvap in kJ/mol = q in J / n in mol / 1000. This calculation assumes the entered heat is the energy for the phase change alone. If heat also warmed the liquid, vapor, or equipment, that energy must be separated before applying the formula.
Worked Example
Using the calculator defaults, q = 40,600 J and n = 1 mol.
- Divide heat by amount: ΔHvap = 40,600 J / 1 mol = 40,600 J/mol.
- Convert joules to kilojoules: 40,600 J/mol / 1000 = 40.600 kJ/mol.
- Rounded to the calculator’s three decimal places, the result is 40.600 kJ/mol. Heat per mole is 40,600.00 J/mol.
Assumptions
- The entered heat is for the liquid-to-vapor phase change, not for heating the sample to its boiling point or superheating the vapor.
- The amount entered is the quantity that actually vaporizes.
- Heat is transferred at constant pressure, the usual context for enthalpy.
- The sample is treated as a pure substance with a defined phase-change condition; the calculation does not correct for impurities or changing pressure.
What Enthalpy of Vaporization Means
Enthalpy of vaporization, often written ΔHvap or ΔHvap, is the enthalpy change when a liquid becomes a gas. It is usually reported per mole, so values for different sample sizes can be compared. Vaporization requires energy because molecules must overcome attractive interactions in the liquid. The energy is absorbed from the surroundings or a heater even when the liquid’s temperature stays constant during boiling.
At a substance’s boiling point for a given pressure, added energy primarily drives the phase change rather than raising the temperature. The reverse process, condensation, releases approximately the same amount of energy per mole at the same conditions, with the opposite sign: ΔHcond = −ΔHvap.
Enthalpy is a state-function change, while heat q describes energy transferred along a particular process. They are equal in the simple calculation when the phase change occurs at constant pressure and other energy effects are negligible. That distinction matters in experiments: a heater’s total electrical energy is not automatically the sample’s enthalpy of vaporization.
When to Use This Calculator
Use it when you know the heat associated with vaporizing a sample and the number of moles vaporized, such as in a classroom calculation or a properly analyzed calorimetry result. It answers the question “How much energy per mole is required?” It does not predict a value from a substance’s name, temperature, or pressure; those require reference data or a more detailed thermodynamic model.
For example, if 40.6 kJ is attributed to vaporizing 1 mol, the molar enthalpy is 40.6 kJ/mol. If the same 40.6 kJ vaporizes 2 mol, the result is 20.3 kJ/mol. Check that the amount and heat refer to the same sample and process. For bench work, follow your lab method, the safety data sheet (SDS) and your supervisor.
Choosing Inputs and Checking Results
- Use consistent units. Enter heat in joules and amount in moles. Convert kilojoules to joules by multiplying by 1000, and millimoles to moles by dividing by 1000, before entry.
- Use the vaporized amount. If only part of a sample changes phase, use the moles of that part, not the starting amount of liquid.
- Check what the heat measurement includes. Energy for warming the liquid to its boiling point, warming vapor, and heating a container is not latent heat of vaporization.
- Interpret the sign. This calculator assumes positive heat supplied to vaporize the liquid and reports a positive magnitude. For condensation, the enthalpy change has the opposite sign.
The formula has no maximum input, but it cannot give a meaningful result if the amount is zero. The calculator rejects zero or negative inputs. A plausible-looking answer is not proof that a measured heat has been correctly isolated from other energy flows.
Limits, Conditions, and Common Misconceptions
Enthalpy of vaporization depends on temperature and pressure. A value quoted at a normal boiling point is not necessarily the value at another pressure or temperature. At the critical point, liquid and vapor become indistinguishable, so the latent heat of vaporization approaches zero; the ordinary liquid-to-vapor phase-change description no longer applies in the same way.
A common mistake is to treat “heat required to boil” as the same as “heat required to vaporize.” Heating a liquid from its starting temperature to its boiling point takes sensible heat, often estimated with q = mcΔT. Vaporizing it then requires latent heat. If both stages are included in a measured total, subtract the warming contribution—and any other relevant losses or equipment heating—before using this calculator.
Another common confusion is between molar enthalpy and specific latent heat. Molar enthalpy is energy per mole, commonly kJ/mol; mass-specific latent heat is energy per unit mass, such as J/kg. To convert between them, the substance’s molar mass is needed. Do not compare values in different units without converting them.
Frequently Asked Questions
What is the formula for enthalpy of vaporization?
For a phase change at constant pressure, divide heat supplied for vaporization by the amount vaporized: ΔHvap = q/n. With q in joules and n in moles, the answer is J/mol.
What units should I use in the calculator?
Enter heat in joules and amount in moles. The main result is displayed in kJ/mol, with an additional result in J/mol.
Can I calculate enthalpy of vaporization from mass?
Yes, if you also know the substance’s molar mass. Convert mass to moles using n = mass / molar mass, then divide the vaporization heat by n. This calculator takes moles directly.
Is enthalpy of vaporization the same as boiling point?
No. Boiling point is a temperature at which a liquid’s vapor pressure matches the surrounding pressure. Enthalpy of vaporization is the energy change per amount needed for the phase change at specified conditions.
Why does the calculator need heat and moles?
The molar value is energy per mole. Heat alone gives total energy for a particular sample, while the mole amount makes the result comparable across sample sizes.
Related
Formula used
in q | Heat transferred to vaporize the sample | J | 40600 | 0 in n | Amount vaporized | mol | 1 | 0 out dh | Enthalpy of vaporization | kJ/mol | q / n / 1000 | 3 out qmol | Heat per mole | J/mol | q / n | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- How to Calculate C Rate for Batteries0.50 h^-1
- Kinetic Energy Calculator: Formula and Examples9.00 J
- Constant Default Rate Formula and Example0.5143 % per month
- Enthalpy Calculator in Btu/lb: Formula and Conversion
- Air Enthalpy Calculator: Temperature and Humidity50.32 kJ/kg dry air
- Molar Enthalpy Calculator: Heat Change per Mole-20.000 kJ/mol