Pure ethanol (ethyl alcohol, C2H5OH) has a density of 0.789 g/mL at 20 °C (0.789 g/cm³). This means 1 milliliter of pure ethanol weighs 0.789 grams. However, density changes with temperature and concentration, so the exact value depends on both factors.
Formula
The density of an ethanol-water mixture at a given temperature is approximated by:
d = (0.806 − 0.00085 × T) × (1 − 0.0022 × (100 − P))
- d = density in g/mL
- T = temperature in °C (range −20 to 100 °C)
- P = purity as mass percent ethanol (0 to 100%)
This is a linear approximation valid for the range shown. For precise work, use standard reference tables (e.g., Perry’s Chemical Engineers’ Handbook or the CRC Handbook).
Worked Example
Using the default values (T = 20 °C, P = 100%):
d = (0.806 − 0.00085 × 20) × (1 − 0.0022 × (100 − 100))
d = (0.806 − 0.017) × (1 − 0)
d = 0.789 × 1 = 0.789 g/mL
This matches the known density of pure ethanol at 20 °C. If you use 40% ethanol (common in spirits), the density becomes approximately 0.935 g/mL at 20 °C.
Assumptions
- The mixture is ethanol and water only (no other solutes).
- The linear temperature coefficient is an approximation; real values deviate slightly, especially near 100 °C.
- The purity is given as mass percent (g ethanol per 100 g solution), not volume percent.
- The mixture is at atmospheric pressure; density changes slightly with pressure.
Why Density Varies with Temperature
Like most liquids, ethanol expands when heated and contracts when cooled. As temperature rises, the same mass occupies more volume, so density decreases. For example:
- At 0 °C: pure ethanol density ≈ 0.806 g/mL
- At 20 °C: ≈ 0.789 g/mL
- At 40 °C: ≈ 0.772 g/mL
- At 60 °C: ≈ 0.755 g/mL
This is why laboratory measurements always record the temperature. A hydrometer reading at 25 °C will differ from one at 15 °C for the same liquid.
Density of Ethanol-Water Mixtures
When ethanol is mixed with water, the density is not a simple linear average. Because ethanol and water molecules interact (hydrogen bonding), the volume of the mixture is slightly less than the sum of the individual volumes. This is called volume contraction.
For practical purposes, you can approximate the density of a mixture using the mass fraction. For example:
- 10% ethanol by mass: density ≈ 0.982 g/mL
- 20%: ≈ 0.969 g/mL
- 50%: ≈ 0.914 g/mL
- 70%: ≈ 0.868 g/mL
- 95% (azeotrope): ≈ 0.804 g/mL
These values are at 20 °C. For exact concentrations, use a standard alcohol density table or an electronic density meter.
Common Mistakes and Misconceptions
Mistake 1: Confusing mass percent with volume percent. Many commercial ethanol solutions are labeled by volume percent (e.g., 70% v/v isopropanol). The density formula above uses mass percent. To convert, you need the density of pure ethanol and water at the given temperature.
Mistake 2: Using the density of pure ethanol for diluted solutions. If you need the mass of 100 mL of 70% ethanol, you cannot multiply 0.789 by 100. You must use the mixture’s density (about 0.868 g/mL for 70% w/w).
Mistake 3: Ignoring temperature. A 10 °C difference can change density by about 0.008 g/mL, which may be significant in precise measurements.
How to Measure Density in the Lab
There are several methods to measure the density of ethanol or its solutions:
- Hydrometer: A glass float that sinks to a level indicating density. Calibrated for a specific temperature (often 20 °C).
- Pycnometer: A precisely calibrated glass bottle. Weigh it empty, filled with water, and filled with the sample. Density = (mass of sample / mass of water) × density of water.
- Digital density meter: Uses the oscillation frequency of a U-shaped tube. Most accurate and requires only a few milliliters.
- Analytical balance and volumetric flask: Weigh a known volume. Simple but requires accurate volume calibration.
Always record the temperature and use a water bath if needed. For flammable ethanol, keep away from open flames and follow your lab’s safety procedures.
Applications and Why It Matters
The density of ethanol is used in many fields:
- Beverage alcohol: Proof and alcohol content are often determined by density measurements.
- Pharmaceuticals: Ethanol is a solvent in many tinctures and extracts; density helps verify concentration.
- Fuel industry: Ethanol-blended gasoline (E10, E85) density affects fuel economy and engine tuning.
- Chemical synthesis: When preparing solutions, density converts between mass and volume.
- Biobanking: Ethanol is used for DNA precipitation; knowing density helps in layering techniques.
In any case, always check the temperature and concentration before using a density value.
Frequently Asked Questions
Q: What is the density of 95% ethanol?
A: At 20 °C, 95% ethanol by mass has a density of approximately 0.804 g/mL. If the 95% is by volume (common in labs), the density is about 0.805 g/mL because the mass percent is slightly lower (~92.4%).
Q: Does ethanol density change with pressure?
A: Yes, but very slightly. At typical laboratory conditions (1 atm), the effect is negligible. For high-pressure applications, you would need compressibility data.
Q: Why is ice less dense than water but ethanol is denser than its vapor?
A: That’s a different comparison. Ethanol is a liquid at room temperature; its density is about 0.789 g/mL. Its vapor (gas) is much less dense. The solid form of ethanol (at −114 °C) is slightly denser than the liquid, unlike water.
Q: How do I convert density to specific gravity?
A: Specific gravity is the ratio of the density of a substance to the density of a reference (usually water at 4 °C, which is 1.000 g/mL). So specific gravity = density (g/mL) / 1.000. For ethanol at 20 °C, specific gravity ≈ 0.789.
Q: Is the density of ethanol the same as the density of ethanol solutions?
A: No. Adding water increases the density because water is denser than ethanol. The more water, the higher the density. For example, 50% w/w ethanol has a density of about 0.914 g/mL at 20 °C.
Q: What is the density of ethanol in kg/m³?
A: To convert g/mL to kg/m³, multiply by 1000. So 0.789 g/mL = 789 kg/m³. This is the SI unit for density.
Related
Formula used
in t | Temperature | °C | 20 | -20 | 100 in p | Purity (mass %) | % | 100 | 0 | 100 out d | Density of ethanol-water mixture | g/mL | (0.806 - 0.00085 * t) * (1 - (100 - p) * 0.0022) | 3
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Grams to Moles Chemistry: How to Convert0.2000 mol/L
- ug to ppb Calculator: Convert Micrograms per Liter1.00 ppb
- Convert ug/l to ppb Calculator
- CPP Calculator Ontario: How CPP Is Calculated162.12 $/month
- Grams to Moles to Molecules: How to Convert0.2000 mol/L
- Organic Chemistry Reaction Calculator: How It Works