molecalculator

Moles & Molar Mass

Ethanol Physical and Chemical Properties

Calculator No. 01-8959 · Updated · Formula and assumptions shown below

Molarity 1.0000 mol/L
Concentration in millimolar
1,000.00 mM
= Molarity × 1000
Mass of ethanol
46.07 g
Set in the form below
Molar mass
46.07 g/mol
Set in the form below
You enter
Mass of ethanol (g), Molar mass (g/mol), Volume of solution (mL)
You get
Molarity (mol/L), Concentration in millimolar (mM)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Ethanol (C2H5OH) is a clear, colorless, volatile liquid with a characteristic odor, a density of 0.789 g/mL at 20 °C, a boiling point of 78.37 °C, and a melting point of –114.1 °C. Chemically, it is a polar, monohydric primary alcohol that is miscible with water in all proportions and readily undergoes oxidation, dehydration, and esterification reactions.

Formula

The calculator converts a mass of ethanol dissolved in a known final volume into molar concentration. The formula is:

Molarity (mol/L) = (mass in grams ÷ molar mass in g/mol) ÷ (volume in mL ÷ 1000)

Where:

  • m = mass of ethanol (g) – default 46.07 g (one mole)
  • mm = molar mass of ethanol (g/mol) – default 46.07 g/mol (C: 12.011×2 + H: 1.008×6 + O: 15.999 = 46.069 g/mol)
  • v = final volume of solution (mL) – default 1000 mL

The first output, molarity, is the primary answer. The second output converts it to millimolar (mM) by multiplying by 1000.

Worked Example

Using the default values: 46.07 g of ethanol (exactly one mole) dissolved in enough water to make 1000 mL (1 L) of solution.

  1. Calculate moles of ethanol: 46.07 g ÷ 46.07 g/mol = 1.000 mol
  2. Convert volume to liters: 1000 mL ÷ 1000 = 1.000 L
  3. Molarity = 1.000 mol ÷ 1.000 L = 1.000 mol/L
  4. Millimolar = 1.000 mol/L × 1000 = 1000.00 mM

The calculator returns 1.0000 mol/L and 1000.00 mM.

Assumptions

  • The solution is at or near room temperature (density changes are ignored for concentration calculations).
  • The final volume is used, not the volume of solvent added (mixing ethanol and water causes volume contraction).
  • The ethanol is pure (100% by mass) and not an aqueous solution like 95% or 70% ethanol.

Physical Properties: State, Boiling Point, and Density

Ethanol is a small, polar molecule (molar mass 46.07 g/mol) that exists as a liquid at room temperature. Its boiling point of 78.37 °C is unusually high for a molecule of this size because of hydrogen bonding between the –OH group and neighboring molecules. For comparison, propane (molar mass 44.1 g/mol) boils at –42 °C. The melting point is –114.1 °C, so pure ethanol never freezes in a standard freezer.

Density is 0.789 g/mL at 20 °C, which is less than water (0.998 g/mL). This is why ethanol floats on water if the two are not mixed. When mixed, the volume contracts: 50 mL ethanol + 50 mL water gives about 96 mL of solution, not 100 mL. This contraction is why the calculator requires a final volume rather than a solvent volume.

Chemical Properties: Polarity and Hydrogen Bonding

The hydroxyl group (–OH) makes ethanol highly polar. The oxygen atom is electronegative and carries a partial negative charge, while the hydrogen on the –OH carries a partial positive charge. This allows ethanol to form hydrogen bonds with other ethanol molecules and with water. As a result, ethanol is completely miscible with water in all proportions, unlike longer-chain alcohols (e.g., 1-butanol is only partially soluble).

Ethanol is also a weak acid, with a pKa of about 16. This means it is a much weaker acid than water (pKa 14). In practice, ethanol does not donate protons in aqueous solution; instead, it acts as a weak base or a nucleophile. The carbon adjacent to the –OH (the α-carbon) is slightly electron-poor, making it susceptible to oxidation.

Reactions: Oxidation, Dehydration, and Esterification

Ethanol undergoes several classic alcohol reactions:

  • Oxidation: With strong oxidizing agents (e.g., K2Cr2O7 in acid), ethanol oxidizes to acetaldehyde (ethanal) and then to acetic acid. In the body, alcohol dehydrogenase performs the same first step.
  • Dehydration: Heating ethanol with concentrated sulfuric acid at 170 °C removes water to form ethylene (ethene). At 140 °C, it forms diethyl ether instead.
  • Esterification: Ethanol reacts with carboxylic acids in the presence of acid catalyst to form ethyl esters (e.g., ethyl acetate from acetic acid). This is the basis of many artificial fruit flavors.
  • Reaction with sodium: Ethanol reacts with metallic sodium to produce sodium ethoxide and hydrogen gas, though more slowly than water does.

Common Problems and Misconceptions

A frequent mistake is confusing 95% ethanol (95% by volume, the azeotrope) with absolute (100%) ethanol. The azeotrope boils at 78.2 °C and cannot be further purified by simple distillation. Another misconception is that “ethanol” and “methanol” are interchangeable – they are not. Methanol is toxic and causes blindness; ethanol is the intoxicating component of alcoholic beverages. In the lab, always check the label for purity and denaturants (e.g., isopropanol or bitterants) that make ethanol undrinkable but unsuitable for some reactions.

When preparing ethanol solutions, remember that the concentration is usually expressed as % v/v (e.g., 70% ethanol for disinfection) or % w/w. A 70% v/v solution means 70 mL ethanol diluted to 100 mL final volume, not 70 mL ethanol plus 30 mL water.

Safety and Handling

Ethanol is highly flammable (flash point 13 °C) and forms explosive vapor-air mixtures between 3.3% and 19% by volume. Keep it away from open flames and hot surfaces. It is also a central nervous system depressant; ingestion causes intoxication and, in large amounts, poisoning. In the laboratory, follow your lab method, the safety data sheet (SDS), and your supervisor. Use proper ventilation to avoid inhaling vapors, and wear gloves because ethanol dries the skin.

Frequently Asked Questions

Does ethanol dissolve in water?

Yes, ethanol is miscible with water in all proportions. The hydroxyl group forms hydrogen bonds with water, and the small ethyl group does not disrupt water’s structure enough to cause phase separation. This is why alcoholic beverages are homogeneous solutions.

Why does ethanol evaporate quickly?

Ethanol has a relatively high vapor pressure (5.95 kPa at 20 °C) compared to water (2.34 kPa). The intermolecular forces are weaker than water’s because ethanol has only one –OH group per molecule, so molecules escape the liquid more readily. This also makes ethanol feel cold on skin due to evaporative cooling.

What is the difference between ethanol and ethyl alcohol?

None – they are two names for the same compound, C2H5OH. “Ethanol” is the systematic IUPAC name; “ethyl alcohol” is a common name. Both refer to the same molecule used in beverages, solvents, and fuel.

Is ethanol a polar or nonpolar solvent?

Ethanol is a polar solvent, but it has a nonpolar ethyl group. This dual nature makes it a versatile solvent that dissolves both polar substances (like salts, though less well than water) and nonpolar substances (like many oils and resins). Its dielectric constant is 24.3 at 25 °C, compared to 78.5 for water.

Why is 100% ethanol difficult to obtain?

Ethanol forms an azeotrope with water at 95.6% ethanol by mass (about 95% by volume). When you distill a dilute ethanol solution, the vapor reaches this composition and cannot be separated further by simple distillation. To get absolute ethanol, you need special dehydrating agents (e.g., molecular sieves) or azeotropic distillation with benzene or cyclohexane.

Related

Formula used
in m | Mass of ethanol | g | 46.07 | 0
in mm | Molar mass | g/mol | 46.07 | 0.001
in v | Volume of solution | mL | 1000 | 0.001
out c | Molarity | mol/L | m / mm / (v / 1000) | 4
out cmm | Concentration in millimolar | mM | c * 1000 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →