Specific enthalpy is enthalpy per unit mass, calculated as h = H/m; for a simple compressible substance, its specific enthalpy is also written h = u + pv. Enter internal energy, pressure, and specific volume to calculate h, or use the mass-based form when total enthalpy and mass are known. The result is specific enthalpy in joules per kilogram (J/kg).
Formula
For a simple compressible system, specific enthalpy is the sum of specific internal energy and pressure multiplied by specific volume:
h = u + pv
- h is specific enthalpy, measured here in kJ/kg.
- u is specific internal energy, in kJ/kg.
- p is pressure. The calculator uses kPa.
- v is specific volume, in m³/kg.
The units make the pressure-volume term consistent: 1 kPa·m³/kg equals 1 kJ/kg, because 1 kPa = 1 kN/m² and 1 kN·m = 1 kJ. The second output converts the result to J/kg using 1 kJ = 1000 J.
Specific enthalpy can also be calculated from total enthalpy and mass: h = H/m, where H is in joules and m is in kilograms. That definition applies broadly. The relation h = u + pv is the useful property relation for a simple compressible substance, with consistent units and a defined thermodynamic state.
Worked Example
Using the calculator’s default values, u = 2500 kJ/kg, p = 100 kPa, and v = 0.001 m³/kg:
- Calculate the pressure-volume contribution: pv = 100 kPa × 0.001 m³/kg = 0.10000 kJ/kg.
- Add it to internal energy: h = 2500 kJ/kg + 0.10000 kJ/kg = 2500.1 kJ/kg.
- Convert to joules per kilogram: 2500.1 × 1000 = 2,500,100 J/kg.
The headline result is 2500.100 kJ/kg when rounded to three decimal places, equivalent to 2,500,100 J/kg. The pressure-volume contribution is comparatively small in this example, but it is part of the enthalpy definition and can be substantial in other states.
Assumptions
- The calculator uses the simple compressible property relation h = u + pv.
- All inputs refer to the same substance and thermodynamic state.
- Pressure is absolute pressure, not gauge pressure.
- The selected units are kJ/kg, kPa, and m³/kg; the unit conversion follows 1 kPa·m³ = 1 kJ.
- No reference state is imposed. Internal energy and enthalpy values depend on the chosen reference convention.
What Specific Enthalpy Means
Enthalpy is a thermodynamic property defined as H = U + pV for a simple compressible system, where U is internal energy and V is total volume. Dividing by mass gives h = u + pv. “Specific” means per unit mass, just as specific volume is volume per unit mass and specific internal energy is internal energy per unit mass.
Enthalpy is especially useful for analyzing flowing fluids. A fluid entering or leaving a control volume carries energy associated with its internal state and the pressure work required to move it across the boundary. That combination is represented by enthalpy. In a steady-flow energy balance, enthalpy commonly appears alongside kinetic energy and potential energy; the balance may also include heat transfer, shaft work, and changes in flow conditions.
Specific enthalpy is a property of a thermodynamic state, not a measure of heat currently “stored” in a substance in a way that is independent of reference choice. Its absolute numerical value depends on the reference state used in a table or model. Differences in enthalpy between states are generally what energy calculations need, and those differences are meaningful when the same reference convention is used throughout.
Using the Formula in Practice
Use h = u + pv when the internal energy, pressure, and specific volume for the same state are available. Thermodynamic tables often provide enthalpy directly, so a separate calculation may not be necessary. For a state described by other properties, such as temperature and pressure, consult the appropriate property table or validated equation of state to obtain the needed properties.
- Check that the pressure is absolute. If a gauge reading is used, convert it using the local atmospheric pressure before applying the relation.
- Make sure specific volume is volume per mass, not total volume. If total volume V and mass m are known, use v = V/m.
- Keep units consistent. This calculator uses kPa and m³/kg, which produce kJ/kg for pv.
- Use values from one consistent state and one consistent reference convention.
For example, a system with total enthalpy H = 12,000 J and mass m = 3 kg has h = 12,000/3 = 4,000 J/kg, or 4 kJ/kg. That route uses the defining “per unit mass” calculation and does not require separate pressure and volume values.
Common Errors and Limits
A frequent mistake is mixing units. Multiplying pressure in pascals by specific volume in m³/kg gives J/kg, whereas pressure in kPa gives kJ/kg. A result may therefore be off by a factor of 1000 if the unit conversion is overlooked. Similarly, confusing density ρ in kg/m³ with specific volume v in m³/kg leads to an incorrect pressure-volume term; when density is known, v = 1/ρ.
Another common issue is using gauge pressure as if it were absolute pressure. Thermodynamic state relations ordinarily use absolute pressure. Gauge pressure is measured relative to the surrounding atmosphere and must be converted before use. Also avoid combining an internal-energy value from one table or reference convention with values from another without checking their definitions.
The equation h = u + pv is not a substitute for finding the correct state properties. Real substances may require property tables or an equation of state, especially near phase changes or at conditions where ideal-gas approximations are unsuitable. For an ideal gas, enthalpy is often treated as a function of temperature alone, but that is a model-specific result—not a universal rule for all fluids.
Frequently Asked Questions
What is the formula for specific enthalpy?
For a simple compressible substance, h = u + pv. Specific enthalpy can also be found from total enthalpy divided by mass: h = H/m.
What is the SI unit of specific enthalpy?
The SI unit is joules per kilogram (J/kg). Kilojoules per kilogram (kJ/kg) are also commonly used in thermodynamics.
Is specific enthalpy the same as internal energy?
No. Specific enthalpy includes the pressure-volume contribution: h = u + pv. The difference can be small or large depending on the state and substance.
Can specific enthalpy be negative?
It can be negative under some reference conventions. The zero point of enthalpy is chosen by convention, so a negative value does not automatically indicate an error; state differences and consistent reference choices matter.
Why do steam tables list enthalpy directly?
Tables provide properties calculated or measured for specified states, avoiding the need to determine internal energy and specific volume separately. Always verify the table’s units, state conditions, and reference convention.
Related
Formula used
in u | Specific internal energy | kJ/kg | 2500 | 0 in p | Pressure | kPa | 100 | 0 in v | Specific volume | m^3/kg | 0.001 | 0 out h | Specific enthalpy | kJ/kg | u + p * v | 3 out hj | Specific enthalpy | J/kg | h * 1000 | 0
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Normality to g/L Converter & Formula29.220 g/L
- Normality to meq/mL Conversion Calculator1.0000 meq/mL
- Normality Test Q-Q Plot: How to Read It
- Normality Test Results: How to Analyze Them
- Normality Slay the Spire?
- Normality Test for Paired t Test: How to Check