molecalculator

Moles & Molar Mass

Formula for Thermal Expansion: Linear & Volume

Calculator No. 01-8861 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The formula for linear thermal expansion is ΔL = α·L₀·ΔT, where ΔL is the change in length, α is the coefficient of linear expansion, L₀ is the original length, and ΔT is the temperature change. For volume expansion, use ΔV = β·V₀·ΔT, where β is the coefficient of volume expansion (approximately 3α for isotropic solids). This calculator computes the change in length or volume for a given material, original dimension, and temperature difference.

Formula

Linear expansion: ΔL = α · L₀ · ΔT

  • ΔL – change in length (m, cm, ft, etc.)
  • α – coefficient of linear expansion (1/°C or 1/K)
  • L₀ – original length (same unit as ΔL)
  • ΔT – temperature change (K or °C, same magnitude)

Volume expansion: ΔV = β · V₀ · ΔT

  • ΔV – change in volume (m³, L, etc.)
  • β – coefficient of volume expansion (1/°C or 1/K)
  • V₀ – original volume
  • ΔT – temperature change

For isotropic solids, β ≈ 3α. For liquids, β is measured directly. The coefficient α is usually given in units of 10⁻⁶/°C (e.g., steel α = 12×10⁻⁶/°C).

Worked Example

Using the calculator defaults: linear expansion, α = 12×10⁻⁶ /°C, L₀ = 2.0 m, ΔT = 40 °C.

ΔL = 12×10⁻⁶ × 2.0 × 40 = 12×10⁻⁶ × 80 = 0.00096 m = 0.96 mm.

Final length L_f = 2.0 + 0.00096 = 2.00096 m.

The calculator shows ΔL = 0.000960 m and L_f = 2.000960 m (6 decimal places).

Assumptions

  • The coefficient α (or β) is constant over the temperature range – true for small ΔT (typically < 100 °C for metals).
  • The material is homogeneous and isotropic (same properties in all directions) – not true for composites or crystals.
  • No phase change occurs (solid to liquid, etc.) – expansion is different across phase transitions.
  • For volume expansion of solids, β = 3α is an approximation that holds for isotropic materials.

How Thermal Expansion Works

When a material is heated, its atoms vibrate more vigorously. In most solids, this increased vibration pushes atoms slightly farther apart on average, so the material expands. The expansion is proportional to the temperature change and the original size. This is why railroad tracks have gaps, bridges have expansion joints, and power lines sag more on hot days.

The coefficient α is a material property. For example:

  • Steel: 12×10⁻⁶ /°C
  • Aluminum: 23×10⁻⁶ /°C
  • Glass (Pyrex): 3.3×10⁻⁶ /°C
  • Concrete: 10-14×10⁻⁶ /°C
  • Water (volume expansion near 20 °C): 207×10⁻⁶ /°C

Note that water is unusual – it contracts when heated from 0 °C to 4 °C, then expands above 4 °C.

Linear vs. Volume Expansion

Linear expansion applies to one dimension (length of a rod, diameter of a hole). Volume expansion applies to three dimensions (a cube, a liquid in a container). For a solid that expands equally in all directions, the volume expansion coefficient is approximately three times the linear coefficient. For a liquid, you only have volume expansion – you cannot measure a “length” of a liquid.

When a solid object with a hole is heated, the hole expands as if it were made of the same material – it does not shrink. For example, a metal washer’s hole gets larger when heated, not smaller.

Common Mistakes and Misconceptions

  • Using °C vs. K incorrectly: ΔT in °C equals ΔT in K (a change of 1 °C = a change of 1 K). So you can use either, but never add 273.15 to ΔT.
  • Forgetting to convert units: α is often given in 10⁻⁶/°C; you must multiply by 10⁻⁶. For example, α = 12×10⁻⁶, not 12.
  • Confusing α and β: Use α for length, β for volume. For solids, β ≈ 3α, but for liquids, β is a separate value (often much larger).
  • Assuming expansion is linear over huge temperature ranges: The formula is an approximation; for large ΔT, α changes with temperature.

Real-World Applications

Engineers use thermal expansion calculations to design:

  • Expansion joints in bridges and railway tracks – to prevent buckling.
  • Thermostats – bimetallic strips bend because two metals expand at different rates.
  • Pipelines – to avoid stress and rupture when hot fluids flow.
  • Precision instruments – to maintain accuracy over temperature changes.
  • Jewelry and dental fillings – to match expansion of surrounding materials.

For example, a 100 m steel bridge (α = 12×10⁻⁶/°C) will expand by 12×10⁻⁶ × 100 × 50 = 0.06 m = 6 cm for a 50 °C temperature change. That gap must be accommodated.

Limits of the Formula

The simple formula ΔL = α·L₀·ΔT works well for small temperature changes (typically less than 100 °C) and for most engineering materials. For large temperature changes, α is not constant – it increases with temperature. For example, steel’s α rises from about 11×10⁻⁶/°C at 20 °C to 14×10⁻⁶/°C at 500 °C. In such cases, you need to integrate α(T) over the temperature range, or use a polynomial approximation.

Also, the formula assumes the material is free to expand. If the material is constrained (e.g., a rod clamped at both ends), it will develop thermal stress, not expansion. The stress can be calculated as σ = E·α·ΔT, where E is Young’s modulus.

Frequently Asked Questions

What is the coefficient of thermal expansion for water?

Water’s volume expansion coefficient is about 207×10⁻⁶/°C at 20 °C, but it is highly temperature-dependent. Between 0 °C and 4 °C, water contracts instead of expanding – that’s why ice floats and lakes freeze from the top down.

Does thermal expansion apply to gases?

Yes, but gases expand much more than solids or liquids. For an ideal gas at constant pressure, volume is proportional to temperature (Charles’s law: V/T = constant). The volume expansion coefficient for an ideal gas at 0 °C is 1/273 ≈ 0.00366 /°C, which is about 300 times larger than steel’s.

Why do railroad tracks have gaps?

To allow for thermal expansion. Without gaps, the tracks would buckle on hot days. Modern welded rails are pre-stressed – they are stretched and welded under tension so that on hot days they are in compression but still within safe limits.

How do I convert α from 1/°C to 1/K?

You don’t need to – the numerical value is the same because a change of 1 °C equals a change of 1 K. Only absolute temperatures differ (0 °C = 273.15 K), but ΔT is identical.

What is the expansion of a steel pipe 10 m long heated from 20 °C to 80 °C?

ΔT = 60 °C, α = 12×10⁻⁶/°C. ΔL = 12×10⁻⁶ × 10 × 60 = 0.0072 m = 7.2 mm. The pipe lengthens by about 7 mm.

Does a hole in a metal plate get bigger or smaller when heated?

It gets bigger. The material around the hole expands outward, so the hole expands as if it were filled with the same material. This is a common misconception – people think the hole shrinks because the material expands into it, but that’s not the case.

Related

Formula used
in sel | Expansion type | Linear=1, Volume=2
in m | Coefficient (α for linear, β for volume) | 1/°C | 0.000012 | 0 | 0.001
in L | Original length (linear) or volume (volume) | m or m³ | 2.0 | 0 | 1000
in dT | Temperature change ΔT | °C | 40 | 0 | 1000
out dL | Change in length or volume | m or m³ | m * L * dT | 6
out Lf | Final length or volume | m or m³ | L + dL | 6

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →