molecalculator

Moles & Molar Mass

Concentration Formula: Calculate Molarity

Calculator No. 01-3770 · Updated · Formula and assumptions shown below

Molarity 0.2000 mol/L
Concentration in millimolar
200.00 mM
= Molarity × 1000
Mass of solute
2.922 g
Set in the form below
Molar mass
58.44 g/mol
Set in the form below
You enter
Mass of solute (g), Molar mass (g/mol), Final solution volume (mL)
You get
Molarity (mol/L), Concentration in millimolar (mM)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Use the molarity formula to calculate concentration: molarity, C = moles of solute (n) ÷ final solution volume in liters (V). This calculator uses a solute’s mass and molar mass to find moles, then divides by the solution volume; it returns molarity in mol/L and millimolar concentration in mM.

Formula

The general molarity formula is C = n / V. Here, C is molarity in moles per liter (mol/L), n is the amount of solute in moles (mol), and V is the final volume of the solution in liters (L). If the amount is given as a mass, calculate moles using n = m / M, where m is solute mass in grams (g) and M is molar mass in grams per mole (g/mol).

Combining those relationships gives C = m / (M × V), with V in liters. This calculator accepts volume in milliliters and converts it explicitly: C = m / M / (v / 1000). The conversion is 1 L = 1000 mL. To express molarity in millimolar, use concentration (mM) = C × 1000, because 1 mol/L = 1000 mmol/L.

  • m: mass of solute, in g.
  • M: molar mass of the solute, in g/mol.
  • v: final solution volume, in mL.
  • C: molarity, in mol/L.

Worked Example

For the calculator’s defaults, the solute mass is 2.922 g, its molar mass is 58.44 g/mol, and the final solution volume is 250 mL.

  1. Calculate the amount in moles: n = 2.922 g / 58.44 g/mol = 0.050000 mol.
  2. Convert the volume to liters: V = 250 mL / 1000 = 0.250 L.
  3. Calculate molarity: C = 0.050000 mol / 0.250 L = 0.2000 mol/L.
  4. Convert to millimolar: 0.2000 mol/L × 1000 = 200.00 mM.

The result is 0.2000 mol/L, or 200.00 mM. The 58.44 g/mol molar mass is the conventional value for sodium chloride, calculated from the abridged standard atomic weights Na = 22.990 and Cl = 35.45 g/mol.

Assumptions

  • The entered mass is pure solute, and the molar mass matches the chemical form actually used.
  • The entered volume is the final volume of the solution, not the volume of solvent added.
  • The result is formal molarity; it does not account for chemical reaction, ion pairing, or changes in activity.
  • Where bench work is involved, follow your lab method, the safety data sheet (SDS) and your supervisor.

What Concentration Means

Concentration describes how much of a specified substance is present in a defined amount of mixture or solution. Molarity is one common way to express it: it counts the amount of solute in moles per liter of the complete solution. The word “concentration” can also refer to other measures, so a value is not fully clear unless its unit and basis are stated.

For example, mass concentration might be written in g/L, while a mass fraction is often expressed as a percentage. These quantities answer different questions and cannot be substituted into the molarity formula without conversion and any necessary substance-specific information. Molarity is especially useful in chemistry calculations involving reacting amounts because balanced equations relate substances by moles.

When to Use Molarity

Use molarity when the available information is an amount in moles and a final solution volume, or when a chemical calculation requires mol/L. If you know mass rather than moles, the calculator first converts mass to moles using molar mass. For an unknown solute, molar mass must be established from its chemical identity and formula; it cannot be inferred from mass and volume alone.

Molarity is volume-based, so temperature can matter: liquids and solutions expand or contract as temperature changes. A stated molarity is tied to the volume at the conditions at which it is defined or measured. For precise work, use the temperature and preparation conventions required by the applicable method.

Common Mistakes and Limits

  • Using solvent volume instead of final volume: A solution made by dissolving solute in 250 mL of water does not necessarily have a final volume of 250 mL. The formula requires the total solution volume after the solute is dissolved.
  • Mixing milliliters and liters: Molarity uses liters. Convert mL to L by dividing by 1000 before dividing moles by volume.
  • Entering the wrong molar mass: Check the formula, hydration state, and chemical form. A hydrate and its anhydrous compound have different molar masses.
  • Confusing molarity with amount: Moles measure how much substance is present; molarity is amount per volume. A solution’s total moles cannot be determined from molarity alone without its volume.
  • Rounding too early: Keep extra digits through intermediate calculations and round the final result to match the precision of the measurements. A calculator’s displayed digits do not imply that the original measurements were equally precise.

The calculation assumes the entered solute amount remains the relevant amount in the solution. If substances react, precipitate, evaporate, or otherwise change form, the simple mass-to-molarity calculation may not describe the concentration of the species of interest. In concentrated solutions, interactions between particles also mean that molarity may not behave like an ideal measure of chemical activity.

Frequently Asked Questions

What is the basic formula for concentration?
For molarity, use C = n / V: divide the solute amount in moles by the final solution volume in liters. If you have mass, first calculate moles as mass divided by molar mass.

How do I calculate concentration from mass and volume?
Divide mass in grams by molar mass in g/mol to get moles, convert the final volume to liters, then divide moles by liters. In symbols, C = m / (M × V).

Does concentration use the volume of water or the final solution?
Use the final solution volume. The solvent volume alone may differ from the total volume after solute is dissolved.

How do I convert mol/L to mM?
Multiply mol/L by 1000. For example, 0.20 mol/L equals 200 mM.

Is molarity the same as concentration?
Molarity is one type of concentration, measured in mol/L. Other concentration units, such as g/L or percent by mass, describe different quantities and require appropriate conversions before comparison.

Related

Formula used
in m | Mass of solute | g | 2.922 | 0
in mm | Molar mass | g/mol | 58.44 | 0.001
in v | Final solution volume | mL | 250 | 0.001
out c | Molarity | mol/L | m / mm / (v / 1000) | 4
out cmm | Concentration in millimolar | mM | c * 1000 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →