molecalculator

Moles & Molar Mass

Free Energy Progress of Reaction Graph Explained

Calculator No. 01-12040 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

A free energy progress of reaction graph plots the Gibbs free energy (G) of a reacting system against the reaction coordinate, showing how energy changes as reactants convert to products. You read the graph to find the activation energy (the barrier height) and the overall free energy change (ΔG), which tells you whether a reaction is spontaneous and how fast it is likely to proceed.

Formula

The graph itself has no single formula—it is a visual representation of the energy landscape along a reaction coordinate. The two key quantities are:

  • ΔG (Gibbs free energy change, kJ/mol): the difference in free energy between products and reactants. ΔG = Gproducts − Greactants. If ΔG < 0, the reaction is exergonic (spontaneous under standard conditions).
  • Ea (activation energy, kJ/mol): the height of the energy barrier from reactants to the transition state. This determines the rate constant via the Arrhenius equation: k = A·e−Ea/(RT), where R = 8.314 J/(mol·K) and T is temperature in kelvin.

The calculator above converts an activation energy into a relative rate constant (compared to a hypothetical reaction with Ea = 0) at a given temperature. It also echoes the ΔG you enter, so you can see both the thermodynamic and kinetic information from a graph.

Worked Example

Using the default values: ΔG = −50 kJ/mol, Ea = 75 kJ/mol, T = 25 °C.

  1. Convert temperature to kelvin: T = 25 + 273.15 = 298.15 K.
  2. Compute the exponent: −Ea/(R·T) = −75,000 J/mol / (8.314 J/(mol·K) × 298.15 K) = −75,000 / 2,479.0 = −30.25.
  3. Rate constant relative to Ea=0: k = e−30.25 ≈ 7.3 × 10−14 (dimensionless ratio).

So at 25 °C, a reaction with a 75 kJ/mol barrier is about 7 × 10−14 times as fast as it would be with no barrier. The ΔG of −50 kJ/mol indicates the reaction is spontaneous, but the large barrier means it will be extremely slow without a catalyst.

Assumptions

  • The Arrhenius equation assumes a single, well-defined transition state and a constant pre-exponential factor A.
  • The graph assumes a simple two-state reaction (reactants → transition state → products) without intermediates.
  • ΔG is for standard conditions (1 bar, 25 °C) unless otherwise noted; actual conditions shift the values.
  • The calculator uses the ideal gas constant R = 8.314 J/(mol·K) and assumes the activation energy is independent of temperature over the range considered.

How to Read the Graph

The horizontal axis is the reaction coordinate—a measure of progress from reactants (left) to products (right). The vertical axis is Gibbs free energy. Key features:

  • Reactants level: the starting free energy.
  • Products level: the ending free energy. If lower than reactants, ΔG is negative (spontaneous).
  • Transition state peak: the highest point on the curve. The vertical difference from reactants to this peak is Ea.
  • Intermediates: if present, appear as local minima between peaks.

A common misconception is that a negative ΔG means the reaction will happen quickly. That is false—kinetics (Ea) and thermodynamics (ΔG) are independent. A reaction can be highly spontaneous yet essentially inert due to a high barrier (e.g., diamond converting to graphite).

Why the Curve Has That Shape

As reactants approach, their electron clouds repel, raising energy. Bonds stretch and partially break, while new bonds begin to form. At the transition state, bonds are partially broken and formed—an unstable, high-energy configuration. After that, new bonds stabilize, lowering the energy to the product level. This gives the characteristic hill shape. For an exergonic reaction, the product side is lower; for endergonic (ΔG > 0), the product side is higher.

Common Mistakes and Misconceptions

  • Confusing ΔG with ΔG°: ΔG° is for standard conditions; actual ΔG depends on concentrations and temperature.
  • Thinking the peak is a stable species: The transition state is not isolable—it is a fleeting configuration.
  • Forgetting that the graph shows free energy, not enthalpy: Entropy changes can make a reaction spontaneous even if enthalpy is positive.
  • Using the wrong units: Activation energy is often in kJ/mol, but the Arrhenius equation requires J/mol to match R in J/(mol·K).
  • Assuming the reverse reaction has the same barrier: The reverse activation energy is Ea − ΔG (for exergonic forward).

How Catalysts and Temperature Affect the Graph

A catalyst lowers the activation energy by providing an alternative pathway with a lower transition state. The graph shows a new, lower peak, but the reactant and product levels remain unchanged—so ΔG is unaffected. Temperature does not change the shape of the free energy curve itself, but it changes the rate constant exponentially via the Arrhenius equation: higher T increases k, effectively making the barrier easier to overcome. In the calculator, raising T from 25 °C to 50 °C for Ea = 75 kJ/mol gives k ≈ 6.9 × 10−12, about 100 times faster.

Limitations of the Graph

The simple one-hump graph is an oversimplification. Real reactions may have multiple steps, each with its own transition state, and the reaction coordinate may involve several geometric changes. The graph also assumes a single, well-defined energy surface; in solution, solvent effects can alter energies. For quantitative predictions, you need computational chemistry or experimental kinetics, not just the graph. The calculator here only computes the Arrhenius factor from Ea and T; it does not account for the pre-exponential factor A, which varies with molecular size and collision frequency.

Frequently Asked Questions

What is the difference between ΔG and activation energy?

ΔG is the net free energy difference between products and reactants—it tells you whether the reaction is spontaneous (negative ΔG) and how much energy is released or absorbed. Activation energy is the energy barrier that must be overcome to reach the transition state—it determines the rate. A reaction can have a very negative ΔG but a high Ea, making it slow.

Why does the graph peak in the middle?

The peak represents the transition state, where bonds are partially broken and formed. This configuration is unstable because it has high potential energy from electron repulsion and incomplete bonding. The system must pass through this high-energy state to convert reactants to products, hence the energy hill.

Does a catalyst change ΔG?

No. A catalyst lowers the activation energy by providing an alternative reaction pathway, but it does not change the starting or ending free energies. Therefore, ΔG remains the same. The catalyst only speeds up the reaction, not the thermodynamics.

Can a reaction with positive ΔG still occur?

Yes, if it is coupled to a more exergonic reaction (e.g., ATP hydrolysis) or if the system is not at standard conditions. The overall ΔG of coupled reactions can be negative. In a closed system at equilibrium, a positive ΔG means the reaction will not proceed spontaneously as written, but under non-standard concentrations, it might.

How do I estimate Ea from a graph?

Measure the vertical distance from the reactant energy level to the top of the peak on the graph. If the axes are labeled in kJ/mol, that distance is the activation energy. For a reverse reaction, measure from the product level to the peak.

Why does the calculator give a rate constant relative to Ea=0?

Because the absolute rate constant depends on the pre-exponential factor A, which is specific to each reaction and not available from the graph alone. The calculator isolates the exponential factor, which is the part that changes with Ea and T. To get a real rate, multiply by an experimentally determined A.

Related

Formula used
in dg | Free energy change ΔG | kJ/mol | -50 | -1000
in ea | Activation energy Ea | kJ/mol | 75 | 0
in t | Temperature | °C | 25 | -273.15
out k | Rate constant relative to Ea=0 | - | exp(-ea / (8.31446261815324 * (t + 273.15)) * 1000) | 4
out dg | ΔG in kJ/mol | kJ/mol | dg | 1

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →