molecalculator

Moles & Molar Mass

Gas Constant in k: R in J/(mol·K) Explained

Calculator No. 01-3348 · Updated · Formula and assumptions shown below

Amount of gas 1,000.0014 mol
Gas constant
8.314463 J/(mol·K)
= 8.31446261815324
Pressure
101.325 kPa
Set in the form below
Gas volume
22.414 L
Set in the form below
You enter
Pressure (kPa), Gas volume (L), Temperature (K)
You get
Amount of gas (mol), Gas constant (J/(mol·K))
Rounding
4 dp · 6 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The gas constant, usually written R, is 8.31446261815324 J/(mol·K) in SI units. If you mean “k” as kelvin, that is the temperature unit in the denominator: R is measured per mole per kelvin, not a separate gas constant called “k.” This calculator uses the ideal gas law to find the amount of gas in moles from pressure, volume, and temperature.

Formula

The ideal gas law is PV = nRT. Rearranging it to calculate amount of gas gives n = PV/(RT).

  • n is amount of gas, in moles (mol).
  • P is absolute pressure. The calculator accepts kilopascals (kPa) and converts to pascals by multiplying by 1,000.
  • V is gas volume. The calculator accepts litres (L) and converts to cubic metres by multiplying by 0.001.
  • T is absolute temperature, in kelvins (K).
  • R is the molar gas constant, 8.31446261815324 J/(mol·K), equivalent to 8.31446261815324 Pa·m³/(mol·K).

The calculator’s amount expression applies those conversions: n = (P × 1,000) × (V × 0.001) / (R × T). The factors of 1,000 and 0.001 cancel numerically, so the block expresses this as n = P × V / (R × T / 1,000), with pressure in kPa and volume in L. The result is the ideal-gas estimate, not a direct measurement.

Worked Example

Using the calculator’s defaults—pressure 101.325 kPa, volume 22.414 L, and temperature 273.15 K—calculate the amount in moles:

n = (101.325 kPa × 22.414 L) / (8.31446261815324 J/(mol·K) × 273.15 K / 1,000)

n = 2,270.17215 / 2.271095 ≈ 0.99959 mol

To four decimal places, the calculator returns 0.9996 mol. The small difference from 1 mol comes from the rounded volume default: the ideal molar volume at 273.15 K and 101.325 kPa is about 22.41397 L. The second output simply reports the SI gas constant, 8.314463 J/(mol·K), rounded to six decimal places.

Assumptions

  • The gas is treated as ideal, so its particles have negligible volume and intermolecular attraction.
  • Pressure is absolute pressure, not gauge pressure.
  • Temperature is entered in kelvins, not degrees Celsius.
  • Pressure and volume refer to the same gas sample and state.

What the Gas Constant Means

R is a proportionality constant connecting pressure, volume, amount, and temperature for an ideal gas. In PV = nRT, it makes the units on both sides agree: pressure times volume has units of energy, while nRT has units mol × J/(mol·K) × K, which also reduces to joules.

The value is universal for ideal-gas calculations when expressed in a consistent unit system. It is not a different physical constant for each gas. Real gases can depart from ideal behavior, especially at high pressure or near condensation, but that changes how well the ideal gas law describes a sample—not the value of R.

In kinetic theory, the gas constant is related to Boltzmann’s constant by R = NAkB, where NA is Avogadro’s constant and kB is Boltzmann’s constant. The lowercase k in that relation often means kB, not kelvin. Kelvin is written K, without a degree sign. This distinction helps resolve the common question “gas constant in k?”: the SI value is per kelvin, while kB is a separate constant used per particle.

Common Values and Unit Forms

The numerical value of R changes when its units change. These are equivalent forms, not different constants:

  • 8.31446261815324 J/(mol·K), the SI form used by this calculator.
  • 0.0820574 L·atm/(mol·K), useful when pressure is in atmospheres and volume in litres.
  • 0.0831446 L·bar/(mol·K), useful with pressure in bar and volume in litres.

Do not insert a value in one unit system into an equation using another. For example, using 0.0820574 with pressure in kPa without converting pressure will give the wrong result. The calculator avoids that particular mismatch by accepting kPa and L while applying the SI value with explicit conversions.

Using the Calculator and Reading the Result

Enter the sample’s absolute pressure, its volume, and its temperature in kelvins. The first output is the estimated amount of gas in moles; the second identifies the constant used. For a gas-law problem that gives moles and asks for volume, the same equation can be rearranged to V = nRT/P. For pressure or temperature, rearrange it to isolate the unknown while keeping all units consistent.

Temperature conversion is a frequent source of error: convert Celsius to kelvins with T(K) = t(°C) + 273.15. For instance, 25 °C is 298.15 K, not 25 K. Also check that volume is the gas volume at the stated pressure and temperature, rather than the capacity of a container under different conditions.

Limits and Common Mistakes

The ideal gas model is a useful approximation, but it is not exact for all conditions. At elevated pressures or temperatures near a substance’s boiling point, interactions between particles can matter. More advanced equations of state may be needed for accurate real-gas calculations. The calculator also assumes that all inputs describe one consistent state; mixing a volume measured at one temperature with pressure from another state is invalid unless the sample’s change of state is accounted for.

  • Use absolute pressure. If a gauge reports pressure above the surrounding atmosphere, add atmospheric pressure to obtain absolute pressure.
  • Use kelvins, not Celsius, in the gas-law equation.
  • Keep units compatible and convert before substituting values.
  • Do not interpret more displayed digits as greater experimental precision; the result cannot be more reliable than its input measurements and model.

For a bench calculation, follow your lab method, the safety data sheet (SDS) and your supervisor.

Frequently Asked Questions

What is the gas constant R in kJ/(mol·K)?
It is 0.00831446261815324 kJ/(mol·K), because 1 kJ equals 1,000 J.

Is the gas constant the same as Boltzmann’s constant?
No. The molar gas constant applies per mole, while Boltzmann’s constant, kB, applies per particle. They are connected by R = NAkB.

Why is R sometimes 0.0821?
That is a rounded value of about 0.0820574 L·atm/(mol·K). It is convenient when using litres and atmospheres, but not when using SI pressure in pascals without conversion.

Is K kelvin or a variable in the gas law?
K is the symbol for kelvin, the SI temperature unit. In PV = nRT, temperature must be an absolute temperature in kelvins; the letter R names the gas constant.

When does the ideal gas law become inaccurate?
It can become less accurate at high pressure, at low temperature, or near condensation, where molecular size and attractions matter more. A real-gas model is appropriate when that deviation is significant for the calculation.

Related

Formula used
in p | Pressure | kPa | 101.325 | 0
in v | Gas volume | L | 22.414 | 0
in t | Temperature | K | 273.15 | 0
out n | Amount of gas | mol | p * v / (8.31446261815324 * t / 1000) | 4
out r | Gas constant | J/(mol·K) | 8.31446261815324 | 6

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →