Half-Life RTX is an official, free remaster of the original 1998 Half-Life that adds full ray tracing, DLSS 3.5, and remade high-resolution textures, releasing in 2025 as a mod for the Steam version. You enable it by downloading it from the Steam store, installing it, and launching it from your library. This article explains what the RTX remaster includes, the hardware you need, how it compares to the original, and common issues players run into.
Formula
The molarity (concentration in mol/L) of a solution is the amount of solute in moles divided by the volume of the final solution in liters:
c = m / (MM × V)
- m – mass of solute in grams (g)
- MM – molar mass of the solute in grams per mole (g/mol)
- V – final solution volume in liters (L), converted from mL by dividing by 1000
- c – molarity in moles per liter (mol/L), often written as M
The calculator also shows the concentration in millimolar (mM), which is just the molarity multiplied by 1000.
Worked Example
Using the default values from the calculator: you dissolve 2.922 g of sodium chloride (NaCl, molar mass 58.44 g/mol) and bring the final volume to 250 mL. What is the molarity?
- Convert volume to liters: 250 mL ÷ 1000 = 0.250 L
- Calculate moles of NaCl: 2.922 g ÷ 58.44 g/mol = 0.05000 mol
- Divide moles by volume: 0.05000 mol ÷ 0.250 L = 0.2000 mol/L
The result is 0.2000 M (200.0 mM). The calculator shows 0.2000 mol/L and 200.00 mM, matching these steps.
Assumptions
- The solute is pure and fully dissolves.
- The final volume (not the solvent volume) is measured after dissolution.
- Temperature is assumed to be near 25 °C; molarity changes slightly with temperature because volume changes.
- No chemical reaction or hydration changes the amount of solute.
When to Use This Calculation
This is the standard formula for preparing a solution of known concentration in a chemistry lab, biology lab, or classroom. You use it whenever you need to make a specific molar solution from a solid reagent – for example, making 0.5 L of 1 M glucose for a cell culture medium, or preparing a buffer component like Tris-HCl at a set molarity. It is also the basis for dilution calculations, where you start from a stock solution and add solvent.
Always remember that molarity is moles per liter of final solution, not per liter of solvent added. If you add 250 mL of water to 2.922 g of NaCl, the final volume might be slightly more than 250 mL, so you would need to adjust to get exactly 0.2000 M.
Common Mistakes
- Using solvent volume instead of final volume – always fill to the mark in a volumetric flask after dissolving.
- Forgetting to convert mL to L – a classic error that gives a result 1000× too large.
- Using the wrong molar mass – check the formula of the compound, especially hydrates (e.g., CuSO₄·5H₂O has a higher molar mass than anhydrous CuSO₄).
- Rounding too early – keep at least 4 significant figures until the final step.
Limits of the Formula
The formula assumes the solute dissolves completely and that the solution behaves ideally. For very concentrated solutions, the volume may not be exactly additive, and for weak acids or bases, the actual concentration of ions differs from the formal molarity. The molarity also varies with temperature because liquids expand, so for precise work, control the temperature. This calculation is for planning and study purposes only – always follow your lab method, the safety data sheet (SDS), and your supervisor when preparing real solutions.
Frequently Asked Questions
What is the difference between molarity and molality? Molarity (mol/L) depends on the volume of solution, which changes with temperature. Molality (mol/kg of solvent) is based on the mass of solvent, which is temperature-independent. Use molality for experiments that involve temperature changes, like freezing-point depression.
How do I make a solution if I only know the mass of solute? Use the same formula: divide the mass by the molar mass to get moles, then divide by the desired molarity to get the final volume in liters. For example, to make 0.5 M from 5 g of NaOH (MM=40.00), moles = 5/40 = 0.125 mol, volume = 0.125/0.5 = 0.25 L.
Why is the final volume not equal to the volume of solvent added? When a solid dissolves, the ions or molecules occupy space between the solvent molecules, so the total volume can increase or decrease slightly. That is why you dissolve the solute in less solvent, then add solvent to the final mark.
Can I use this calculator for dilution problems? No – dilution uses the formula M₁V₁ = M₂V₂, where you start with a concentrated stock and add solvent. This calculator is for preparing a solution from a solid. Use the site’s dilution calculator for that.
What if my solute is a liquid, like hydrochloric acid? For a liquid reagent, you need its density and weight percent to find the mass of pure HCl in a given volume. Then you can treat that mass as the solute. This calculator works for any solute once you know the mass of the pure compound.
Related
Formula used
in m | Mass of solute | g | 2.922 | 0 in mm | Molar mass | g/mol | 58.44 | 0.001 in v | Final solution volume | mL | 250 | 0.001 out c | Molarity | mol/L | m / mm / (v / 1000) | 4 out cmm | Concentration in millimolar | mM | c * 1000 | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Normality to g/L Converter & Formula29.220 g/L
- Normality to meq/mL Conversion Calculator1.0000 meq/mL
- Normality Test Q-Q Plot: How to Read It
- Normality Test Results: How to Analyze Them
- Normality Slay the Spire?
- Normality Test for Paired t Test: How to Check