Heat release in a spark-ignition (SI) engine is usually calculated from the measured in-cylinder pressure and cylinder volume as the crankshaft turns, using a first-law energy balance. This calculation estimates the apparent rate of heat addition to the gas; it is not a direct measurement of flame heat or fuel energy. Enter pressure, crank angle, cylinder geometry, and the gas-property ratio to calculate apparent heat release per crank-angle degree and its cumulative total.
Formula
For a closed cylinder, a common single-zone apparent heat-release relation is dQapp/dθ = [γ/(γ − 1)]p(dV/dθ) + [1/(γ − 1)]V(dp/dθ). Here Qapp is apparent heat added to the cylinder contents in joules, θ is crank angle in degrees, p is absolute cylinder pressure in pascals, V is cylinder volume in cubic metres, and γ is the ratio of specific heats, cp/cv, treated here as constant.
The calculator uses a finite-difference form over two measurements: ΔQapp/Δθ = [γ/(γ − 1)]Δ(pV)/Δθ + pavgΔV/Δθ, where pavg = (p1 + p2)/2. The two terms are algebraically equivalent to the differential relation when pressure and volume change smoothly across the interval; using a finite interval makes the result an average rate over that interval, not an instantaneous value.
- p1 and p2: absolute pressures at the interval endpoints, entered in bar; the expression converts bar to pascals using 100,000 Pa/bar.
- V1 and V2: cylinder volumes in cm³; the expression converts cm³ to m³ using 1,000,000 cm³/m³.
- Δθ: crank-angle interval in degrees.
- γ: dimensionless specific-heat ratio. It depends on gas composition and temperature; 1.35 is an illustrative conventional value, not universal.
- First output q: average apparent heat-release rate in J/deg. Second output ΔQ: estimated apparent heat release across the selected interval in J.
Pressure must be absolute, not gauge pressure. The formula is expressed per crank-angle degree, so its rate is not in watts. To convert to power, engine speed is also needed: at N rpm, one crank-angle degree lasts 1/(6N) seconds, so a rate in J/deg can be multiplied by 6N deg/s to obtain J/s for that operating point.
Worked Example
Using the defaults, pressure rises from 10 bar to 10.2 bar while cylinder volume rises from 50 cm³ to 51 cm³ over 1 degree, with γ = 1.35. Convert the endpoint values: p1 = 10 × 100,000 = 1,000,000 Pa; p2 = 10.2 × 100,000 = 1,020,000 Pa. Also, V1 = 50/1,000,000 = 0.000050000 m³ and V2 = 51/1,000,000 = 0.000051000 m³.
The pressure-volume changes are p1V1 = 50.000 J and p2V2 = 52.020 J, so Δ(pV)/Δθ = (52.020 − 50.000)/1 = 2.0200 J/deg. The mean pressure is 1,010,000 Pa, and ΔV/Δθ = 0.0000010000 m³/deg. Therefore the pressure-volume contribution is [1.35/(1.35 − 1)] × 2.0200 = 7.7914 J/deg, and the volume contribution is 1,010,000 × 0.0000010000 = 1.0100 J/deg.
Adding the terms gives q = 8.8014 J/deg, displayed to three decimals as 8.801 J/deg. Across the 1-degree interval, ΔQ = 8.8014 × 1 = 8.8014 J, displayed as 8.801 J. The value is positive because both pressure and volume increase over this interval.
Assumptions
- The cylinder contents are treated as a spatially uniform, closed gas during the calculation interval.
- Specific-heat ratio γ is constant across the interval; real gas properties change with temperature and composition.
- Pressure and volume data represent the same crank-angle locations and have been correctly synchronized.
- The finite difference represents an average over the entered angle interval. The calculation does not model heat transfer, crevice flow, blow-by, or fuel injection effects separately.
How the Calculation Works
In an SI engine, a spark initiates combustion of the premixed air-fuel charge. Cylinder pressure reflects several effects at once: combustion, piston motion, heat transfer to the walls, gas exchange, and measurement behavior. During the closed portion of the cycle, the pressure trace and the known geometry provide a practical route to estimate how quickly energy is being added to the in-cylinder gas.
The expression combines a pressure-change term and a volume-change term. The latter accounts for work associated with piston motion; the former accounts for the energy change associated with changing pressure. If volume were fixed, the volume term would vanish. If pressure and temperature followed an idealized compression or expansion with no net heat transfer, the terms would tend to balance rather than indicate sustained heat addition.
In data analysis, the equation is commonly applied at every consecutive crank-angle sample, then the interval results are summed to create a cumulative apparent heat-release curve. Smaller angle steps can reveal sharper changes, but they also magnify pressure noise. Filtering and differentiation choices can materially alter peak rate, so analysis methods and resolution should be reported alongside results.
Inputs, Data Quality, and Interpretation
Use absolute pressure and cylinder volume calculated from the engine’s bore, stroke, connecting-rod geometry, and clearance volume. The calculator takes volume directly, which is useful when a geometry model or measured volume trace is already available. A pressure value in bar is converted to pascals internally; volume in cm³ is converted to m³. Do not enter a pressure in kPa or volume in litres without converting it first.
- Use a pressure trace with a known crank-angle reference, and verify that the pressure and volume arrays use the same angle convention.
- Use a positive interval length and preserve the order of the two samples. Reversing the endpoints changes the signs of the differences.
- Choose γ appropriate to the intended approximation and state it. A single constant value is convenient but may not accurately represent hot combustion products throughout the cycle.
- Check units and calibration, and compare the resulting curve with neighboring intervals. Isolated spikes often indicate noise or synchronization errors rather than a physical combustion event.
A positive value indicates estimated net apparent heat addition over the interval under the model. A negative value can occur during expansion when heat transfer out of the gas is important, during other parts of the cycle, or because of noise and modeling limitations. It does not automatically mean that combustion has reversed. Likewise, integrated apparent heat release is not necessarily equal to the fuel’s chemical energy: wall heat loss, crevice effects, incomplete combustion, and the chosen model all matter.
Limits and Common Misconceptions
“Heat release” in this method is apparent, not a direct calorimetric measurement. The calculation infers net energy transfer from pressure and volume behavior, with simplifying assumptions. A detailed analysis may use temperature-dependent specific heats, account for heat transfer and mass leakage, and distinguish burned-gas properties from unburned gas. Those refinements require additional measurements or models and are outside this two-point calculator.
Another common mistake is treating J/deg as a time-based heating rate. It is per crank-angle degree, and the equivalent rate per second changes with engine speed. Also, the pressure-volume product has units of energy, but pressure alone is not heat release: the changing pressure and changing volume both enter the first-law relation. Use this calculation for engineering study and comparison under consistent methods, not as a stand-alone measure of engine efficiency or fuel consumption.
Frequently Asked Questions
What is the heat-release equation for an SI engine?
The common single-zone apparent relation is dQapp/dθ = [γ/(γ − 1)]p(dV/dθ) + [1/(γ − 1)]V(dp/dθ). It estimates heat addition from cylinder pressure and volume changes, assuming a closed, uniform gas and a specified γ.
Why is the result called apparent heat release?
Because it is inferred from pressure-volume data rather than measured directly as chemical heat. The result includes the effects of the model assumptions and does not independently separate combustion energy from wall heat transfer or leakage.
Should cylinder pressure be gauge or absolute?
Use absolute pressure. Gauge pressure omits the surrounding reference pressure; using it directly changes pV and can distort the calculated heat release.
How do I convert J/degree to watts?
At a constant speed of N rpm, crank angle advances at 6N degrees per second. Multiply J/degree by 6N to obtain J/s, or watts, for that speed; this conversion does not make the value independent of engine speed.
Does a negative heat-release rate mean combustion has stopped?
Not necessarily. It can reflect net energy loss from the gas, expansion behavior, heat transfer, measurement noise, or modeling limits. Interpret it with the pressure trace, crank-angle location, and analysis assumptions.
Related
Formula used
in p1 | Pressure at first angle | bar | 10 | 0 in p2 | Pressure at second angle | bar | 10.2 | 0 in v1 | Cylinder volume at first angle | cm^3 | 50 | 0 in v2 | Cylinder volume at second angle | cm^3 | 51 | 0 in da | Crank-angle interval | deg | 1 | 0.000001 in g | Specific-heat ratio gamma | - | 1.35 | 1.000001 out q | Apparent heat release rate | J/deg | (g/(g-1)*((p2*100000*v2/1000000-p1*100000*v1/1000000)/da)+((p1*100000/1000000+p2*100000/1000000)/2)*(v2-v1)/da) | 3 out dq | Apparent heat released over interval | J | q*da | 3
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- MD Calc I:T Ratio Calculator and Explanation0.0500 ratio
- Oxygen Mass Number: Isotope Values Explained16 nucleons
- Mass-to-Light Ratio: Meaning and Calculation1.000 M☉/L☉
- M/z Ratio in Mass Spectrometry: Meaning and Calculation1,000.00 Th
- Mass Fraction to Molar Fraction Calculator
- K2 Molar Mass Calculator and Calculation78.1966 g/mol