molecalculator

Moles & Molar Mass

How to Calculate Density of a Mixed Solution

Calculator No. 01-11132 · Updated · Formula and assumptions shown below

Density 0.800 g/mL
Density in kg/m³
800.0 kg/m³
= Density × 1000
Mass of component 1
50 g
Set in the form below
Mass of component 2
30 g
Set in the form below
You enter
Mass of component 1 (g), Mass of component 2 (g), Final solution volume (mL)
You get
Density (g/mL), Density in kg/m³ (kg/m³)
Rounding
3 dp · 1 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator finds the density of a mixed solution when you know the mass of each component and the total volume. You enter the masses and the final volume, and you get the density in g/mL (or g/cm³). This is useful for lab work, preparing solutions, or checking if a mixture matches expected specifications.

Formula

Density is mass divided by volume. For a mixed solution, the total mass is the sum of the masses of all components (assuming no chemical reaction that changes mass), and the total volume is the final volume of the solution after mixing. The formula is:

ρ = (m₁ + m₂ + … + mₙ) / V

  • ρ (rho) = density of the mixed solution (g/mL or g/cm³)
  • m₁, m₂, … = masses of each component (g)
  • V = final total volume of the solution (mL)

Note: 1 mL = 1 cm³, so density in g/mL is numerically equal to density in g/cm³. To convert to kg/m³, multiply by 1000 (since 1 g/mL = 1000 kg/m³).

Worked Example

Using the default values from the calculator: you mix 50 g of component 1 (e.g., a salt) and 30 g of component 2 (e.g., a sugar) in enough water to make a final volume of 100 mL.

Step 1: Add the masses of the components.

Total mass = 50 g + 30 g = 80 g

Step 2: Divide total mass by the final volume.

Density = 80 g / 100 mL = 0.800 g/mL

Step 3: Convert to kg/m³ if needed.

0.800 g/mL × 1000 = 800 kg/m³

The calculator shows density as 0.800 g/mL, which matches.

Assumptions

  • The masses are additive (no mass is lost or gained during mixing).
  • The final volume is known (not the sum of individual volumes, because volumes are not always additive).
  • The solution is homogeneous (well mixed).
  • Temperature and pressure are constant; density changes with temperature, so the result is valid only at the temperature of measurement.

When to Use This Calculation

This is the standard method for finding density of any mixture where you know the masses of the components and the final volume. It applies to solutions, suspensions, and even solid mixtures if you measure the total volume (e.g., by displacement). It is often used in chemistry labs to prepare solutions with a target density, or to verify the concentration of a solution if you know the density-concentration relationship.

How to Read the Result

The density value tells you how much mass is packed into each unit of volume. A higher density means the solution is heavier per volume, which usually indicates a higher concentration of dissolved solids. Density is temperature-dependent: most liquids expand when heated, so density decreases as temperature rises. Always note the temperature when you record a density.

Common Mistakes

  • Using volume of solvent instead of final volume: When you dissolve a solid in a liquid, the final volume may be slightly more or less than the solvent volume. Always measure the final volume after mixing.
  • Adding volumes of components: Volumes are not always additive (e.g., 50 mL water + 50 mL ethanol gives less than 100 mL). Use the actual final volume, not the sum of parts.
  • Unit mix-ups: If you enter mass in kg and volume in mL, the result will be wrong. Convert all masses to grams and volume to mL (or all to SI units).
  • Forgetting to include all components: If you have three components, you must add all three masses. Omitting one gives a wrong density.
  • Rounding too early: Round only at the final step, not during intermediate calculations.

Tips

  • Always measure the final volume after mixing, using a volumetric flask or graduated cylinder.
  • Use a balance with appropriate precision for the masses.
  • Record the temperature of the solution; if you need to compare densities, do so at the same temperature.
  • If the solution is viscous or has bubbles, let it settle or degas before measuring volume.
  • For accurate work, calibrate your volumetric glassware.

Troubleshooting

  • Result seems too high or too low: Check your mass and volume units. If you used kg and L, the result is in kg/L, which is numerically equal to g/mL, but if you mixed units, you’ll get a nonsense number.
  • Density is negative: This happens if you entered a negative mass or volume. Mass and volume cannot be negative.
  • Result changes with temperature: That’s normal. Density is temperature-dependent. If you need a specific density, control the temperature.
  • Your measured density differs from calculated: This may be due to volume contraction or expansion (e.g., ethanol-water mixtures). The calculation assumes you measured the actual final volume. If you used the sum of volumes, that’s the error.
  • Calculator shows “Cannot compute”: This occurs if the volume is zero or negative. Check your inputs.

Frequently Asked Questions

Can I use this method for gases mixed together?

Yes, but you need to know the mass of each gas and the total volume of the container. For gases, density is often expressed in g/L, so adjust units accordingly.

What if I only know the densities of the pure components, not their masses?

You cannot directly calculate the mixture density without knowing the masses or the volume fractions. If you have volume fractions, you can use the rule of mixtures: ρ_mix = φ₁ρ₁ + φ₂ρ₂, where φ is volume fraction. That is a different calculation.

Does the order of mixing matter?

No, for density, only the final mass and final volume matter, not the order of addition. However, for some chemicals, the order can affect the final volume due to chemical interactions, so measure the final volume after all mixing is done.

Why is the density of a salt solution higher than pure water?

Dissolving a salt adds mass without increasing the volume much, so the mass-to-volume ratio increases, making the density higher.

How do I convert density from g/mL to lb/ft³?

Multiply by 62.428. For example, 1 g/mL = 62.428 lb/ft³. But in most lab work, you stay in metric units.

Can I use this calculator for a mixture of two liquids?

Yes, as long as you know the mass of each liquid and the final volume after mixing. For example, mixing 50 g of ethanol with 50 g of water gives a final volume that is less than 100 mL, so you must measure it.

Related

Formula used
in m1 | Mass of component 1 | g | 50 | 0
in m2 | Mass of component 2 | g | 30 | 0
in v | Final solution volume | mL | 100 | 0.001
out d | Density | g/mL | (m1 + m2) / v | 3
out dm | Density in kg/m³ | kg/m³ | d * 1000 | 1

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →