molecalculator

Moles & Molar Mass

Calculate Enthalpy from Temperature Change

Calculator No. 01-8346 · Updated · Formula and assumptions shown below

Heat absorbed (q) 10,460.0 J
Enthalpy change (ΔH)
10.460 kJ/mol
= Heat absorbed (q) ÷ (Amount of substance × 1000)
Mass of substance
100 g
Set in the form below
Specific heat capacity
4.184 J/(g·°C)
Set in the form below
You enter
Mass of substance (g), Specific heat capacity (J/(g·°C)), Temperature change (ΔT) (°C), Amount of substance (mol)
You get
Heat absorbed (q) (J), Enthalpy change (ΔH) (kJ/mol)
Rounding
1 dp · 3 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This guide shows you how to calculate the enthalpy change (ΔH) of a process from temperature measurements. You’ll learn the fundamental equation q = mcΔT, how to apply it to calorimetry experiments, and how to convert the heat absorbed or released into enthalpy per mole. You’ll need the mass of the substance, its specific heat capacity, the temperature change, and, for molar enthalpy, the number of moles involved.

Formula

The core relationship is:

q = m × c × ΔT

Where:

  • q = heat absorbed or released (joules, J)
  • m = mass of the substance (grams, g)
  • c = specific heat capacity (J/(g·°C)) – the energy needed to raise 1 g of the substance by 1 °C
  • ΔT = temperature change (final temperature − initial temperature, °C)

For enthalpy change per mole:

ΔH = q / n (in J/mol, often converted to kJ/mol by dividing by 1000)

Where n is the amount of substance in moles. If the reaction releases heat (exothermic, ΔT positive for the surroundings), ΔH is negative; if it absorbs heat (endothermic, ΔT negative for the surroundings), ΔH is positive.

Worked Example

Using the calculator defaults: 100 g of water (c = 4.184 J/(g·°C)) is heated from 20 °C to 45 °C, so ΔT = 25 °C. The amount of substance is 1 mole (for simplicity).

Step 1: Calculate the heat absorbed:

q = 100 g × 4.184 J/(g·°C) × 25 °C = 10,460 J

Step 2: Convert to kJ: 10,460 J ÷ 1000 = 10.46 kJ

Step 3: Divide by moles to get ΔH: ΔH = 10.46 kJ / 1 mol = 10.46 kJ/mol

The calculator shows q = 10460.0 J and ΔH = 10.460 kJ/mol, matching the manual calculation.

Assumptions

  • The specific heat capacity is constant over the temperature range.
  • No heat is lost to the surroundings (perfect insulation).
  • The substance is pure and uniform.
  • For molar enthalpy, the amount of substance is known and the process is stoichiometrically simple.
  • Pressure is constant (which is typical for calorimetry at atmospheric pressure).

When to Use This Method

This calculation is used in calorimetry experiments to determine the heat of reactions, phase changes, or physical processes. For example, mixing an acid and base in a coffee-cup calorimeter, measuring the temperature rise, and then calculating the enthalpy of neutralization. It also applies to heating or cooling a pure substance without a phase change, or to finding the specific heat capacity of an unknown metal by measuring the temperature change of water.

How to Read the Result

The sign of ΔH tells you whether the process is exothermic (negative, heat released) or endothermic (positive, heat absorbed). The magnitude is the energy per mole. For example, ΔH = -55.8 kJ/mol for the neutralization of a strong acid and base means each mole of water formed releases 55.8 kJ. Always report the sign and units.

Common Mistakes

  • Forgetting the sign of ΔT: ΔT is final minus initial. If the temperature drops, ΔT is negative, and q is negative (heat released).
  • Unit mix-ups: Specific heat is often given in J/(g·°C) but sometimes in J/(kg·K) or cal/(g·°C). Convert everything to consistent units. 1 cal = 4.184 J, 1 kg = 1000 g, and a 1 °C change equals a 1 K change.
  • Using the wrong mass: For reactions in solution, use the total mass of the solution (solvent + solute), not just the solute.
  • Ignoring the calorimeter’s heat capacity: In a real experiment, the calorimeter itself absorbs heat. If significant, add its heat capacity (C_cal) to the calculation: q_total = (m·c + C_cal)·ΔT.
  • Rounding too early: Keep extra significant figures until the final step to avoid rounding errors.

Tips

  • Always measure the initial and final temperatures carefully, and stir the mixture to ensure uniform temperature.
  • If you’re calculating molar enthalpy, convert the mass of the limiting reactant to moles using its molar mass.
  • For reactions in solution, assume the solution has the same density and specific heat as water (1 g/mL and 4.184 J/(g·°C)) unless stated otherwise.
  • Use a graphical method (temperature vs. time) to extrapolate the initial and final temperatures if the reaction is fast and heat loss is significant.
  • Run a blank or calibration experiment to account for heat loss to the environment.

Troubleshooting

If your calculated ΔH seems too high or too low: Check the mass – did you include the entire solution? Check the specific heat – is it for the correct substance? Also verify that the temperature change is measured in °C (or K) and not Fahrenheit.

If the sign is opposite to expected: You may have reversed the initial and final temperatures. Remember, for an exothermic reaction, the temperature of the surroundings increases, so ΔT is positive, but the system loses heat, so q and ΔH are negative. Make sure you are consistent about what system you are tracking.

If the result is not reproducible: Heat loss to the environment is the usual culprit. Use a lid on the calorimeter, insulate it, and record the temperature quickly. Also, ensure the reactants are well mixed.

If you get a negative mass or temperature change: Double-check your inputs – negative values are only valid for ΔT if the temperature drops, but mass and specific heat must always be positive.

Frequently Asked Questions

Q: What is the difference between heat (q) and enthalpy (H)?
A: Heat (q) is the energy transferred due to a temperature difference. Enthalpy (H) is a state function that includes internal energy plus pressure-volume work. At constant pressure (common in open calorimetry), the heat transferred equals the change in enthalpy (q_p = ΔH).

Q: Can I use this formula for phase changes like melting or boiling?
A: No. During a phase change, the temperature stays constant while heat is absorbed or released. You need the latent heat (enthalpy of fusion or vaporization) instead: q = n × ΔH_fus or q = m × L, where L is the specific latent heat.

Q: Why is the specific heat of water 4.184 J/(g·°C)?
A: It’s a defined value based on the calorie (1 cal = 4.184 J). Water has a high specific heat because of hydrogen bonding, making it useful as a heat reservoir in calorimetry.

Q: How do I find the specific heat capacity of an unknown substance?
A: Use a calorimeter: heat a known mass of the substance to a known temperature, place it in a known mass of water at a lower temperature, measure the final equilibrium temperature, and solve for the unknown c using q_lost = q_gained.

Q: What is the difference between ΔH and ΔH°?
A: ΔH° (standard enthalpy change) is measured under standard conditions (usually 1 bar pressure and a specified temperature, often 25 °C). ΔH can be at any conditions. For many calculations, the difference is small, but for precise work, note the conditions.

Q: Does the calculator account for heat loss to the environment?
A: No, it assumes perfect insulation. In real experiments, you must correct for heat loss using a cooling curve or a calibration factor. The calculator gives the ideal value.

Related

Formula used
in m | Mass of substance | g | 100 | 0.001
in c | Specific heat capacity | J/(g·°C) | 4.184 | 0.0001
in dt | Temperature change (ΔT) | °C | 25 | -273.15
in n | Amount of substance | mol | 1 | 0.000001
out q | Heat absorbed (q) | J | m * c * dt | 1
out dh | Enthalpy change (ΔH) | kJ/mol | q / (n * 1000) | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →