This guide shows you how to calculate the enthalpy (total heat content) of outdoor air using its dry-bulb temperature and relative humidity. You’ll get a value in kJ per kg of dry air, which is essential for HVAC load calculations, psychrometric analysis, and designing ventilation systems. You’ll need a calculator or the interactive tool below, and the formulas are provided step by step.
Formula
The enthalpy of moist air is the sum of the enthalpy of dry air and the enthalpy of the water vapor mixed with it. The standard formula is:
h = 1.006 × T + W × (2501 + 1.86 × T)
Where:
- h = specific enthalpy of moist air (kJ/kg dry air)
- T = dry-bulb temperature (°C)
- W = humidity ratio (kg water vapor per kg dry air)
- 1.006 = specific heat of dry air at constant pressure (kJ/(kg·°C))
- 2501 = latent heat of vaporization of water at 0°C (kJ/kg)
- 1.86 = specific heat of water vapor (kJ/(kg·°C))
The humidity ratio W is calculated from relative humidity (RH) and saturation pressure:
W = (RH/100) × 0.622 × Pws / (Patm − (RH/100) × Pws)
Where:
- Pws = saturation vapor pressure of water (kPa), approximated by the Magnus formula: Pws = 0.6108 × exp(17.27 × T / (T + 237.3))
- 0.622 = ratio of the molar mass of water (18.015 g/mol) to dry air (28.97 g/mol)
- Patm = atmospheric pressure, taken as 101.325 kPa at sea level (adjust if your altitude differs)
The calculator above uses these exact expressions, with Patm fixed at 101.325 kPa.
Worked Example
Calculate the enthalpy of outdoor air at 25°C dry-bulb and 50% relative humidity.
Step 1: Find saturation vapor pressure
Pws = 0.6108 × exp(17.27 × 25 / (25 + 237.3)) = 0.6108 × exp(1.648) = 0.6108 × 5.196 = 3.174 kPa
Step 2: Find humidity ratio
W = (50/100) × 0.622 × 3.174 / (101.325 − (50/100) × 3.174) = 0.5 × 0.622 × 3.174 / (101.325 − 1.587) = 0.987 / 99.738 = 0.00990 kg/kg
Step 3: Calculate enthalpy
h = 1.006 × 25 + 0.00990 × (2501 + 1.86 × 25) = 25.15 + 0.00990 × (2501 + 46.5) = 25.15 + 0.00990 × 2547.5 = 25.15 + 25.22 = 50.37 kJ/kg dry air
The calculator gives 50.37 kJ/kg dry air, matching our manual calculation.
Assumptions
- Atmospheric pressure is 101.325 kPa (sea level). At higher altitudes, enthalpy will be slightly lower for the same T and RH because the humidity ratio is lower.
- The Magnus formula is an approximation valid from about −40°C to 60°C, which covers most outdoor conditions.
- Air is treated as a mixture of ideal gases; water vapor behaves ideally.
- The reference state is 0°C for both dry air and liquid water, which is the common HVAC convention.
- Relative humidity is expressed as a percentage, not a decimal.
When to Use This Calculation
Outdoor air enthalpy is used in HVAC design to determine the cooling or heating load from ventilation air. When you bring outdoor air into a building, you must condition it to indoor conditions. The enthalpy difference between outdoor and indoor air, multiplied by the mass flow rate of air, gives the energy required. This calculation is also used to decide when to use economizer cooling—when outdoor enthalpy is lower than return air enthalpy, it is more efficient to use outdoor air for free cooling.
How to Read the Result
The result is the total heat content per kilogram of dry air. A higher enthalpy means the air carries more energy—either because it is hotter, more humid, or both. For example, warm humid air has a much higher enthalpy than warm dry air because of the latent heat in water vapor. When comparing two air conditions, the one with higher enthalpy will require more cooling energy to bring it down to a given indoor condition.
Common Mistakes
- Using RH as a decimal instead of a percentage: If you enter 50 instead of 0.50 in the formula, you get a wildly wrong W and h. Always divide RH by 100.
- Forgetting to convert temperature to Celsius: The formula requires °C. If you have Fahrenheit, subtract 32 and multiply by 5/9 first.
- Using the wrong atmospheric pressure: At high altitudes, 101.325 kPa is too high. For Denver (1,600 m), use about 84 kPa. This changes W and h by several percent.
- Mixing up enthalpy units: This formula gives kJ/kg dry air. Some charts use BTU/lb dry air. To convert, multiply kJ/kg by 0.4299 to get BTU/lb.
- Rounding intermediate values too early: If you round W to 0.01, you’ll get a very different h. Keep at least 4 significant figures until the final step.
Tips
- For quick estimates, you can use a psychrometric chart: find the intersection of dry-bulb temperature and relative humidity, then read the enthalpy lines (which slope up to the left).
- If you only have wet-bulb temperature, you can find enthalpy directly from a psychrometric chart, but the formula above requires dry-bulb and RH.
- For HVAC load calculations, always use design conditions (e.g., 1% summer design dry-bulb and mean coincident wet-bulb) rather than average conditions.
- When comparing outdoor and return air, use enthalpy, not just temperature. A warm dry day may have lower enthalpy than a cool humid day.
Troubleshooting
Result seems too high or too low: Check that RH is between 0 and 100 and temperature is in °C. For typical outdoor air (0–40°C, 20–80% RH), enthalpy ranges from about 5 to 120 kJ/kg. If you get a negative value, your temperature is below −40°C or you entered RH as a decimal.
Calculator shows ‘Cannot compute’: This happens if the denominator (Patm − (RH/100) × Pws) becomes zero or negative, which occurs when RH is 100% and temperature is near the boiling point. At sea level, this is around 100°C, which is outside the input range. If you’re at high altitude, lower the temperature or RH.
Your result doesn’t match a psychrometric chart: Charts may use a different reference state (e.g., 0°C for dry air but 0°C for liquid water, which is what we use) or a different atmospheric pressure. Also, some charts use the ASHRAE formulation that includes the enthalpy of liquid water below 0°C, which can cause small differences.
You need enthalpy at a different altitude: Modify the calculator’s Patm value. For example, at 1,500 m, Patm ≈ 84.5 kPa. You can manually compute using the formulas above with your local pressure.
Frequently Asked Questions
What is the difference between enthalpy and temperature? Temperature measures the average kinetic energy of molecules, while enthalpy includes both sensible heat (related to temperature) and latent heat (related to moisture content). Two air samples at the same temperature can have very different enthalpies if one is humid.
Why do HVAC engineers use enthalpy instead of temperature for economizers? Because enthalpy represents the total energy needed to condition air. A day at 24°C with 90% RH may have higher enthalpy than a day at 30°C with 30% RH, so using enthalpy prevents unnecessary cooling energy.
Can I use this formula for indoor air? Yes, it works for any moist air condition, but it’s most often used for outdoor air because indoor conditions are usually controlled and known.
What if I only have wet-bulb temperature? On a psychrometric chart, the wet-bulb lines are nearly parallel to enthalpy lines, so you can read enthalpy directly from the chart. To calculate it numerically, you’d need to solve for humidity ratio using the wet-bulb equation, which is more complex.
How does altitude affect enthalpy? At higher altitudes, atmospheric pressure is lower, so the humidity ratio for a given RH is lower, which reduces enthalpy. For example, at 25°C and 50% RH, enthalpy is about 50.4 kJ/kg at sea level but about 49.0 kJ/kg at 1,500 m.
Is the enthalpy value per kg of dry air or per kg of moist air? It’s per kg of dry air, which is the standard convention in psychrometrics. The dry air mass is constant, while water vapor mass varies, so using dry air as the basis makes calculations easier.
Related
Formula used
in t | Dry-bulb temperature | °C | 25 | -40 | 60 in rh | Relative humidity | % | 50 | 0 | 100 out h | Enthalpy | kJ/kg dry air | 1.006*t + (2501 + 1.86*t) * (rh/100 * 0.622 * psat/(p_atm - rh/100*psat)) | 2 out psat | Saturation vapor pressure | kPa | 0.6108*exp(17.27*t/(t+237.3)) | 3 out w | Humidity ratio | kg water/kg dry air | rh/100 * 0.622 * psat/(p_atm - rh/100*psat) | 4
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Normality to g/L Converter & Formula29.220 g/L
- Normality to meq/mL Conversion Calculator1.0000 meq/mL
- Normality Test Q-Q Plot: How to Read It
- Normality Test Results: How to Analyze Them
- Normality Slay the Spire?
- Normality Test for Paired t Test: How to Check