This purity calculator works out what percentage of a sample’s mass is the desired substance. Enter the mass of the pure substance and the total sample mass to get percent purity; you will need reliable measurements or an assay result for both.
Formula
Percent purity = (mass of pure substance ÷ total mass of sample) × 100. Here, mass of pure substance is the mass attributable to the wanted compound, in grams; total mass of sample is the mass of the entire sample being assessed, also in grams. The units must match, though any consistent mass unit works. The impurity percentage is 100% minus the purity percentage, assuming the sample consists of the desired substance and impurities and the assay accounts for all of it.
The calculator assumes the pure-substance mass is not greater than the sample mass. Its inputs cannot be negative, but if you enter a pure mass larger than the total, the result is physically inconsistent and should not be used. Check the measurements before interpreting the output.
Worked Example
Using the calculator’s defaults, the sample weighs 10 g and contains 8 g of the desired substance.
- Divide the pure-substance mass by the total sample mass: 8 g ÷ 10 g = 0.8.
- Convert the fraction to a percentage: 0.8 × 100 = 80.00% purity.
- Find the impurity fraction by difference: 100 − 80.00 = 20.00% impurities.
The calculator therefore returns 80.00% purity and 20.00% impurity percentage.
Assumptions
- The two mass values describe the same sample and use compatible units.
- The pure-substance mass is determined accurately by a suitable assay or measurement, rather than assumed from the sample’s appearance.
- Impurity percentage is calculated as the remainder; this interpretation requires the sample’s components to be accounted for on the same mass basis.
- For bench work, follow your lab method, the safety data sheet (SDS) and your supervisor.
What You’ll Need
- The total mass of the sample, recorded with its unit and appropriate precision.
- The mass of the desired substance in that sample. This usually comes from a validated assay, certificate, or a clearly defined separation and measurement method.
- A calculator, or the formula above. Use a suitable balance and approved analytical method if you are collecting measurements in a lab.
Step-by-Step
- Define what “pure” means for your task. Identify the target compound or component. Purity is not meaningful until you know which substance counts as the desired material and what impurities or contaminants are included in the assessment.
- Choose the correct basis. This guide calculates mass percent: mass of target divided by total sample mass. Confirm that your assay reports a mass or a result that can be converted to one. A result reported as a volume percentage, mole fraction, or area percentage is not automatically a mass percentage.
- Record the total sample mass. Use the mass of the sample that the purity result describes, not the mass of a container or a larger batch. If the container is included in a weighing, subtract its tare mass. Keep the unit, such as grams or milligrams, beside the number.
- Obtain the target’s mass in the sample. Use an appropriate quantitative method, such as a validated assay or a documented separation followed by measurement. Do not treat the starting mass as the pure mass unless it has actually been established that the sample is pure. Follow the method’s instructions for calibration, sampling and corrections.
- Make units consistent. Convert both masses to the same unit before dividing. For example, 250 mg is 0.250 g. If you use the calculator, it is the ratio that matters, so entering both values in milligrams also works.
- Divide the target mass by the total mass. The result is a decimal fraction. Check that it is between 0 and 1 for a physically consistent sample under this calculation. If it is larger than 1, stop and inspect the values, units, sample identity and assay calculation.
- Multiply by 100. The result is the mass percentage of the desired substance. Report it with appropriate significant figures and state the measurement or assay method when the result is used in a technical context.
- Report uncertainty and conditions when relevant. Measurements and assays have uncertainty. Avoid reporting more decimal places than the method supports. For a formal result, include the sample identification, basis (for example, mass percent), method, and any required uncertainty or acceptance criteria.
Common Mistakes
- Mixing units: dividing milligrams by grams without conversion can make a result wrong by a factor of 1,000. Convert both masses or use matching units.
- Using the wrong denominator: the denominator is the total mass of the sample being assessed. It is not the mass of the target alone, the container, or the solvent used in a separate preparation.
- Assuming a sample is pure: appearance, a label, or a nominal concentration does not establish the actual target mass. Use data from a suitable method.
- Confusing assay percentages: chromatographic peak-area percentage may not equal mass percentage. Detector response can differ between compounds, so use the method’s specified calculation and calibration.
- Over-rounding: rounding intermediate values can shift the final percentage. Keep unrounded values through the calculation, then round the result to match the precision and uncertainty of the data.
- Calling the remainder “impurity” without checking: moisture, residual solvent, counterions, or unmeasured components may be treated differently by a specified method. State the measurement basis.
Tips
- Write the formula and units beside your data before calculating; the mass units cancel in the ratio, leaving a percentage.
- Keep the raw measurements and assay output, not just the final percentage, so another person can reproduce the calculation.
- For a batch made up of several portions, use total target mass divided by total batch mass. Do not average individual purity percentages unless the portions have equal masses.
- Use the method’s stated basis—such as as-received, dry basis, or anhydrous basis—because moisture correction can change the reported purity.
- For a quick reasonableness check, a target mass equal to half the sample mass gives 50% purity; equal masses give 100%.
Troubleshooting
The result is over 100%: verify that the numerator and denominator refer to the same sample, check unit conversions, and review any dilution, recovery, calibration, or blank corrections in the assay. Do not cap the answer at 100%; investigate the inconsistency.
The result is negative or cannot be calculated: masses cannot be negative, and the total sample mass must be greater than zero. Check for a missing value, a minus sign, or a zero denominator. If the target mass exceeds the total, revisit the data rather than forcing a result.
Repeated results disagree: check whether the sample was adequately mixed and whether separate portions are representative. Review balance readability, sample loss, contamination, method precision and calibration. Repeat measurements only as allowed by the written method.
The result differs from a label or specification: confirm that both use the same purity basis, units, lot and method. A supplier or specification value may use a different moisture or assay convention, so compare definitions before drawing conclusions.
Frequently Asked Questions
What is the formula for purity?
For mass purity, divide the mass of the desired substance by the total sample mass and multiply by 100.
Can purity be greater than 100%?
Not as a physically valid mass percentage of a component in the same sample. A value above 100% usually points to a unit, denominator, calibration, or assay problem.
Is purity the same as concentration?
No. Purity describes the fraction of a sample that is the desired substance. Concentration describes how much solute is present in a specified amount of solution or mixture.
Can I calculate purity from a chromatogram?
Not reliably from peak areas alone unless the method supports that interpretation. Different compounds may produce different detector responses; calibrated response factors or another validated method may be required.
How many decimal places should I report?
Use precision justified by the balance and assay uncertainty. Keep extra digits during calculation, then round the final result appropriately and follow any applicable reporting specification.
Does 100% purity mean there are no impurities?
It means none were detected or accounted for under the method and its reporting limit. It does not prove absolute absence of every possible contaminant.
Related
Formula used
in pure | Mass of pure substance | g | 8 | 0 in total | Total mass of sample | g | 10 | 0 out purity | Purity | % | pure / total * 100 | 2 out imp | Impurity percentage | % | 100 - purity | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Isotope Percent Abundance Calculator and How to Use It75.91 %
- Percentage Abundance Calculator and How to Find It
- Isotope Fractional Abundance Calculator and Formula0.2409 fraction
- Percent Abundance Formula: Calculate Isotope Percentages25.00 %
- Isotope Percent Abundance Calculator and How to Use It50.00 %
- Isotope Percent Abundance Calculator and How-To Guide75.91 %