molecalculator

Moles & Molar Mass

How to Calculate RCF in a Centrifuge

Calculator No. 01-2236 · Updated · Formula and assumptions shown below

Relative centrifugal force 280 ×g
Acceleration
2,740.96 m/s²
= Relative centrifugal force × 9.80665
Rotor radius
10 cm
Set in the form below
Rotor speed
5000 RPM
Set in the form below
You enter
Rotor radius (cm), Rotor speed (RPM)
You get
Relative centrifugal force (×g), Acceleration (m/s²)
Rounding
0 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Relative centrifugal force (RCF) expresses the acceleration a sample experiences in a centrifuge as a multiple of Earth’s gravity, or ×g. Enter the rotor radius and speed in revolutions per minute (RPM) to calculate RCF; the result helps you match a protocol’s force without confusing it with RPM.

Formula

Use RCF = 1.118 × 10−5 × r × RPM2, where r is the rotor radius in centimeters and RPM is rotational speed in revolutions per minute. The calculator writes the same formula as 1.118 × r × (RPM / 1000)2; this is algebraically equivalent and keeps the coefficient convenient. RCF is a ratio, reported as ×g, not as a force in newtons. To convert the result to acceleration, use a = RCF × 9.80665 m/s², using standard gravitational acceleration.

The radius is the distance from the axis of rotation to the sample’s position of interest, usually measured to the bottom of the tube for maximum RCF. Manufacturers or rotor documentation may give a maximum radius and an average radius. Use the one specified by your protocol or instrument documentation; do not substitute tube length or rotor diameter. The formula assumes the stated RPM is the actual rotor speed.

Worked Example

Using the calculator’s defaults, radius r = 10 cm and speed RPM = 5000:

  1. Divide RPM by 1000: 5000 / 1000 = 5.
  2. Square the result: 52 = 25.
  3. Multiply by 1.118 and the radius: 1.118 × 10 × 25 = 279.5.
  4. The RCF is 279.5 ×g, displayed to zero decimal places as 280 ×g.
  5. For acceleration, 279.5 × 9.80665 = 2741.958675 m/s², displayed as 2741.96 m/s².

The unrounded RCF is useful for checking the calculation; practical protocols and instrument displays may round differently. Enter the correct rotor radius and speed rather than copying the example values.

Assumptions

  • Radius is measured in centimeters from the rotation axis to the sample location you intend to calculate.
  • Speed is in revolutions per minute, not radians per second or revolutions per second.
  • The calculation uses the standard conversion coefficient and standard gravity, 9.80665 m/s².
  • It calculates nominal RCF from rotor geometry and speed; it does not account for sample movement, rotor condition, acceleration or braking settings, or instrument-specific limitations.

What You’ll Need

  • The rotor’s relevant radius, in centimeters. Check the rotor manual or its specifications if available.
  • The rotor speed in RPM, from the method or the centrifuge setting.
  • A calculator, or the calculator above. Confirm whether your method specifies RCF or RPM before setting a run.

Step-by-Step

  1. Identify the required quantity. Check your written method for a target RCF (×g) or a target RPM. They are not interchangeable: the same RPM produces different RCF values in rotors with different radii.
  2. Find the correct radius. Use the radius associated with your rotor and sample position. For maximum RCF, this is commonly the axis-to-bottom-of-tube distance. For average RCF, use the documented average radius instead. Do not estimate from the rotor’s outside diameter.
  3. Check the radius unit. This formula requires centimeters. Convert millimeters to centimeters by dividing by 10, or meters to centimeters by multiplying by 100. For example, a radius of 100 mm is 10 cm.
  4. Confirm the RPM. Use revolutions per minute. If a display or specification gives revolutions per second, multiply by 60 before using the formula. If the rotor speed is not known, do not guess; consult the method and equipment documentation.
  5. Enter radius and RPM. Put the radius in centimeters and speed in RPM into the calculator. The first result is RCF in ×g. The second result is the equivalent nominal acceleration in m/s².
  6. Compare against the method. If the method gives RCF, compare that value directly with the calculated RCF. If it gives RPM but you need an RCF, calculate using the actual rotor radius. Use the method’s specified radius convention when it provides one.
  7. If you need RPM for a target RCF, rearrange the formula. Use RPM = 1000 × √(target RCF / (1.118 × r)), with radius r in centimeters. For instance, for 1000 ×g at 10 cm: RPM = 1000 × √(1000 / 11.18) ≈ 9460 RPM. Verify that the resulting speed is within the rotor and centrifuge’s stated limits before using it.
  8. Check the equipment limits and setup. Use compatible tubes and a properly balanced rotor, and follow the equipment’s operating instructions and your lab method. Do not exceed the rated speed or force for any component.

For bench work, follow your lab method, the safety data sheet (SDS) and your supervisor.

Common Mistakes

  • Mixing up RPM and RCF: RPM describes rotation speed; RCF describes acceleration relative to gravity. A protocol’s stated number must be interpreted using its stated unit.
  • Using the wrong radius: Radius is measured from the axis, not across the rotor. A radius error changes RCF in direct proportion: doubling the radius doubles the calculated RCF.
  • Entering millimeters as centimeters: A 100 mm radius must be entered as 10 cm. Missing this conversion produces a tenfold error.
  • Forgetting that speed is squared: Doubling RPM makes RCF four times as high, not twice as high. Small RPM changes can therefore make a substantial difference.
  • Using a radius from another rotor: Radius varies by rotor and configuration. A speed setting copied from another setup does not guarantee the same RCF.
  • Rounding too early: Keep the full radius and speed values through the calculation, then round the final result appropriately. The displayed result is rounded to a whole ×g.

Tips

  • Record both the rotor identification and the radius convention used alongside an RCF calculation so it can be checked later.
  • When following a method, prefer its specified RCF and use the matching rotor-radius convention. If the method gives only RPM, check whether it assumes a particular rotor.
  • Use manufacturer documentation for maximum and average radii rather than relying on a visual estimate. These radii give different RCF values at the same speed.
  • Check units every time: centimeters and RPM go into this formula; the output is a dimensionless multiple of g.
  • Use the calculator’s acceleration output only as a unit conversion. Lab protocols generally specify centrifugation conditions as RCF or RPM, not m/s².

Troubleshooting

The result is much too large or small: Recheck that radius is in centimeters, speed is in RPM, and the radius is measured from the rotation axis. Check that RPM was not entered where the radius belongs.

Your calculated RCF does not match the instrument display: Confirm whether the display reports RPM or RCF and which rotor radius it uses. A display may calculate RCF from a stored rotor profile or a particular sample position, while your calculation may use a different radius.

The answer differs from a protocol: Check whether the protocol gives ×g or RPM, and whether it specifies maximum or average radius. Also check for unit conversion or rounding differences. If the protocol’s assumptions are unclear, ask the method owner or supervisor before proceeding.

The required RPM exceeds an equipment limit: Do not run at that speed. Check the rotor and centrifuge ratings and consult your supervisor about an approved setup or method; changing the speed changes the RCF.

Frequently Asked Questions

What does RCF mean in a centrifuge?
RCF means relative centrifugal force. It expresses rotational acceleration as a multiple of standard gravity, written as ×g.

Is RCF the same as RPM?
No. RPM is rotational speed. RCF depends on both RPM and rotor radius, so the same RPM can produce different RCF values in different rotors.

Which radius should I use?
Use the radius specified by your method or rotor documentation. Maximum RCF is commonly based on the distance from the rotation axis to the tube bottom; average RCF uses a different documented position.

Can I calculate RPM from RCF?
Yes. Use RPM = 1000 × √(target RCF / (1.118 × radius in cm)). Confirm the resulting speed is within the equipment’s limits.

Why does doubling RPM quadruple RCF?
RPM is squared in the formula. If radius stays the same, doubling speed multiplies RCF by 22, or four.

Does this calculation tell me how long to centrifuge?
No. It calculates force from radius and speed only. Run time and other settings must come from the validated method for your sample and equipment.

Related

Formula used
in r | Rotor radius | cm | 10 | 0
in rpm | Rotor speed | RPM | 5000 | 0
out rcf | Relative centrifugal force | ×g | 1.118 * r * (rpm / 1000) ^ 2 | 0
out gforce | Acceleration | m/s² | rcf * 9.80665 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →