molecalculator

Moles & Molar Mass

Void Ratio Calculator: Formula and Worked Example

Calculator No. 01-3566 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator works out the soil void ratio, the volume of voids divided by the volume of soil solids. Enter the total sample volume and the volume of solids in matching units; it returns a dimensionless ratio, with porosity as a useful check.

Formula

Void ratio is the volume of voids divided by the volume of soil solids:

e = Vv / Vs = (Vt − Vs) / Vs

  • e is void ratio, a dimensionless number.
  • Vv is the volume of voids in the sample, in cubic metres (m³).
  • Vs is the volume occupied by soil solids, in m³.
  • Vt is total sample volume, in m³; Vt = Vv + Vs.

The calculator finds void volume by subtracting solid volume from total volume, then divides by solid volume. Its second result, porosity n, is the proportion of total volume that is void space, expressed as a percentage: n = Vv / Vt × 100. The two quantities are related by e = n / (1 − n) when n is written as a fraction, or n = e / (1 + e).

Worked Example

Using the calculator’s default values, total sample volume is 0.001 m³ and solid volume is 0.0006 m³.

  1. Find void volume: Vv = Vt − Vs = 0.001 − 0.0006 = 0.0004 m³.
  2. Divide void volume by solid volume: e = 0.0004 / 0.0006 = 0.6667.
  3. For the check, calculate porosity: n = (0.0004 / 0.001) × 100 = 40.00%.

The sample’s void ratio is 0.6667. This means there are about 0.667 volume units of void space for each volume unit of solids. It does not mean that 66.67% of the total sample is void space; the porosity is 40.00%.

Assumptions

  • The two volumes describe the same representative sample and use the same units.
  • Total volume includes both solids and all void space; solid volume excludes pores and gaps.
  • The sample has a positive solid volume, and total volume is at least as large as solid volume.
  • The calculation does not distinguish air-filled voids from water-filled voids or account for changes during sampling.

What You’ll Need

  • Total volume of the soil sample, measured or calculated using a suitable method.
  • Volume of the soil solids, from a valid solids-volume or particle-density measurement.
  • A calculator and consistent units. Convert both volumes to the same unit before entering them.

In soil mechanics, void ratio is commonly obtained from measured soil properties rather than by measuring every pore directly. For example, if dry bulk density and particle density are known, solid volume can be calculated from dry mass divided by particle density, and total volume from dry mass divided by dry bulk density. Make sure the densities use compatible units and refer to the same sample condition. For bench or field work, follow your lab method, the safety data sheet (SDS) and your supervisor.

Step-by-Step

  1. Define the sample. Use one soil specimen and one stated condition, such as its condition at sampling or after compaction. Void ratio can change if soil is disturbed, compressed, dried or wetted.
  2. Determine total volume. Measure the specimen’s overall volume, including the spaces between particles and pores within aggregates. Use a method appropriate to the sample shape and material. Record the units and the measurement precision.
  3. Determine solids volume. Obtain the volume of the mineral and organic solid particles only. Do not use the total sample volume here. If calculating from dry mass and particle density, use Vs = dry mass / particle density, ensuring the density units produce the desired volume unit.
  4. Convert to matching units. Convert both values to m³, or use another single volume unit for both. For example, 1 cm³ = 1 × 10−6 m³. Since the units cancel in the division, the final ratio has no unit, but mixed input units still produce an incorrect answer.
  5. Check the measurements. Total volume must be greater than or equal to solids volume, and solids volume must be greater than zero. If solids volume exceeds total volume, revisit the measurements, conversions and density calculations before proceeding.
  6. Calculate void volume. Subtract solids volume from total volume: Vv = Vt − Vs. This is the combined air-and-water space, not just the air-filled portion.
  7. Divide to obtain void ratio. Calculate e = Vv / Vs. Keep several digits during the calculation and round only the final reported value to a precision supported by the measurements.
  8. Check with porosity. Calculate n = Vv / Vt × 100, or use n = e / (1 + e) × 100. Confirm that porosity is between 0% and 100% and that the two results are consistent.
  9. Report the context. Give the void ratio, sample condition, measurement method and relevant units for the input data. Void ratio itself is unitless, but reporting the method and condition makes comparisons meaningful.

Common Mistakes

  • Confusing void ratio with porosity. Void ratio divides void volume by solids volume; porosity divides void volume by total volume. They are related but are not interchangeable.
  • Using total volume as the denominator. That gives porosity, not void ratio. For e, the denominator must be Vs.
  • Mixing units. Subtracting 0.4 cm³ from 1 m³ without converting first can create a wildly wrong result. Convert both volumes before subtracting or dividing.
  • Using wet mass as dry mass in density calculations. Water contributes to mass but is not part of the soil solids. Use the mass definition required by the method, typically dry mass when calculating solids volume from particle density.
  • Rounding too early. Rounded intermediate volumes can distort the ratio, especially when the void volume is small. Keep unrounded or sufficiently precise values until the final step.
  • Treating all void space as air. Voids may contain water, air or both. Void ratio describes their combined volume and is not a direct measure of air content or saturation.

Tips

  • Use the calculator’s porosity output as an independent cross-check. For example, e = 0.5 corresponds to n = 0.5 / 1.5 = 33.33%.
  • Keep the measured volumes at their recorded precision, and avoid reporting more decimal places than the method justifies.
  • When comparing samples, confirm that both values refer to comparable soil conditions and use compatible measurement methods.
  • If your available data are dry bulk density ρd and particle density ρs, another standard relation is e = ρs / ρd − 1. Use consistent density units and appropriate measured values.

Troubleshooting

The calculator rejects the values: Solid volume must be greater than zero, and total volume cannot be smaller than solid volume. Check for a misplaced decimal, a unit conversion error or values taken from different samples.

The answer is negative: This usually means the entered solids volume exceeds total volume. Do not take the absolute value or reverse the subtraction; verify the measurements and definitions first.

The result seems unusually large: A high ratio can be possible in very loose soil, but first check that the denominator is solid volume and that both inputs use the same units. A cm³-to-m³ mismatch is a common cause.

Porosity and void ratio disagree: Recalculate from the same unrounded values. Use n = e / (1 + e) × 100, or e = n / (1 − n), with n as a fraction in the second formula. Do not insert a percentage such as 40 directly as though it were 0.40.

You only have mass or density data: Identify whether the reported density is dry bulk density or particle density, and use the corresponding relationship. Do not substitute wet bulk density for dry bulk density without accounting for water content.

Frequently Asked Questions

What is a void ratio?
It is the volume of voids in a soil sample divided by the volume of soil solids. It has no units.

Can void ratio be greater than 1?
Yes. It means the void volume is greater than the solid volume. Whether a measured value is plausible depends on the soil and its condition.

Is void ratio the same as porosity?
No. Void ratio uses solid volume as its denominator, while porosity uses total volume. Use n = e / (1 + e) to convert from void ratio to porosity as a fraction.

Can I calculate void ratio from porosity?
Yes. Convert porosity to a fraction first, then calculate e = n / (1 − n). For 40% porosity, e = 0.40 / 0.60 = 0.6667.

Does water in the pores change void ratio?
Water filling existing voids does not by itself change their volume, so it does not change void ratio. Compression, swelling, collapse or other changes to the soil structure can change it.

What units should I use?
Any volume unit works if total volume and solids volume use the same unit. The ratio is dimensionless, but consistent units are essential when finding void volume and dividing.

Related

Formula used
in vt | Total soil volume | m^3 | 0.001 | 0
in vs | Volume of soil solids | m^3 | 0.0006 | 0
out e | Void ratio | - | (vt - vs) / vs | 4
out n | Porosity | % | (vt - vs) / vt * 100 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →