molecalculator

Moles & Molar Mass

How to Calculate Volume of Solution in Chemistry

Calculator No. 01-11990 · Updated · Formula and assumptions shown below

Molarity 0.2000 mol/L
Concentration in millimolar
200.00 mM
= Molarity × 1000
Mass of solute
2.922 g
Set in the form below
Molar mass
58.44 g/mol
Set in the form below
You enter
Mass of solute (g), Molar mass (g/mol), Final solution volume (mL)
You get
Molarity (mol/L), Concentration in millimolar (mM)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator determines the volume of a solution needed to achieve a desired molar concentration (molarity) when you know the mass of solute and its molar mass. You enter the mass of solute, its molar mass, and the target molarity, and you get the required final solution volume in milliliters. This is a core calculation for preparing solutions in the lab, from simple salt solutions to buffers and reagents.

Formula

The molarity (M) of a solution is defined as the number of moles of solute per liter of solution:

M = n / V

where:

  • M = molarity (mol/L, also written as M)
  • n = amount of solute (mol)
  • V = volume of solution (L)

The number of moles (n) is calculated from the mass of solute (m) and its molar mass (MM):

n = m / MM

Combining these gives the formula used by the calculator:

V (L) = m / (MM × M)

To get the volume in milliliters, multiply by 1000:

V (mL) = [m / (MM × M)] × 1000

In the calculator above, the input for volume (v) is in mL, and the output molarity (c) is computed as:

c = m / (MM × (v / 1000))

where v/1000 converts mL to L.

Worked Example

Using the default values from the calculator:

  • Mass of solute (m) = 2.922 g
  • Molar mass (MM) = 58.44 g/mol (this is the molar mass of NaCl)
  • Final solution volume (v) = 250 mL

First, convert volume to liters:

V = 250 mL × (1 L / 1000 mL) = 0.250 L

Calculate moles of solute:

n = m / MM = 2.922 g / 58.44 g/mol = 0.05000 mol

Now calculate molarity:

c = n / V = 0.05000 mol / 0.250 L = 0.2000 mol/L

So the molarity is 0.2000 M (or 200.0 mM). This matches the calculator output (c = 0.2000, cmm = 200.00).

Assumptions

  • The solute is pure and completely dissolves.
  • The final volume is the total volume of the solution after adding solute and solvent (not the volume of solvent alone).
  • The solution is at the temperature for which the molarity is defined; molarity changes slightly with temperature because volume changes.
  • The solute does not react with the solvent or other components (unless intended).

When to Use This Calculation

You use this calculation whenever you need to prepare a solution of a specific molar concentration from a solid reagent. For example, making a 0.5 M NaCl solution for a biological buffer, or a 1 M HCl solution from a stock (though for liquids you would use density and percent composition instead). It is also the reverse of the more common molarity calculation: if you know the desired molarity and the amount of solute you have, you can solve for the volume needed.

How to Read the Result

The first output (Molarity) is the concentration in mol/L. The second output (Concentration in millimolar) is simply the molarity multiplied by 1000, which is useful for dilute solutions. For example, 0.2000 M is the same as 200.0 mM.

Common Mistakes

  • Using solvent volume instead of final volume: When you dissolve a solid, the final volume is usually slightly different from the volume of solvent you started with. Always use a volumetric flask and add solvent up to the mark, not just add the calculated amount of solvent.
  • Unit mismatches: Molar mass must be in g/mol, mass in grams, and volume in liters (or mL, but then convert). Forgetting to convert mL to L is a frequent error.
  • Molar mass errors: Using a wrong molar mass (e.g., using the atomic mass instead of the compound’s molar mass) will give a wrong answer. Double-check the formula of the compound and the atomic weights.
  • Rounding too early: Rounding intermediate values can cause significant errors, especially in dilute solutions. Keep at least 4-5 significant figures until the final answer.

Tips

  • Always use a volumetric flask for precise volume measurements. Add the solute first, dissolve in a small amount of solvent, then fill to the calibration mark.
  • If the solute is hygroscopic (absorbs water), weigh it quickly and use a desiccator if possible.
  • For solutions that change volume with temperature, prepare them at the temperature you will use them, or allow them to equilibrate to that temperature before adjusting the final volume.
  • Use the molar mass from a reliable source (e.g., the IUPAC standard atomic weights) and include the correct number of water molecules if you are using a hydrate (e.g., CuSO4·5H2O).

Troubleshooting

  • If the molarity comes out too high or too low: Check your mass measurement and whether you used the correct molar mass. Also verify that the final volume is exactly as intended.
  • If the solute does not dissolve completely: Some solutes need stirring, heating, or sonication. If it still won’t dissolve, you may have exceeded the solubility limit for that solvent at that temperature.
  • If the calculated volume seems unrealistic: For example, needing 10 L of solution for a few grams of solute. Recheck the desired molarity—it may be too low or too high for the solute amount.
  • If you get a negative number: Ensure all inputs are positive. The calculator rejects negative mass, molar mass, or volume, but if you ever see a negative, check your inputs.

Frequently Asked Questions

What is the difference between molarity and molality?

Molarity (M) is moles of solute per liter of solution, while molality (m) is moles of solute per kilogram of solvent. Molarity depends on temperature because volume changes with temperature, whereas molality does not.

How do I find the molar mass of a compound?

Add the atomic masses of all atoms in the formula. For example, NaCl: 22.99 (Na) + 35.45 (Cl) = 58.44 g/mol. Use the periodic table and be careful with polyatomic ions.

Can I use this calculator for liquid solutes?

This calculator is for solid solutes. For liquids, you typically need the density and percent purity to convert to mass. The formula still applies if you know the mass of the liquid solute, but you would need to measure it by mass, not volume.

What if I need the volume in liters instead of mL?

The calculator outputs volume in mL because that is the most common lab unit. To convert to liters, divide by 1000. For example, 250 mL = 0.250 L.

Does temperature affect the volume calculation?

Yes, because the volume of a solution changes with temperature. Molarity is defined at a specific temperature. If you prepare the solution at a different temperature, the molarity will be slightly different. For precise work, prepare at the same temperature as the intended use.

Why is the final volume not just the volume of solvent added?

When you dissolve a solid, the total volume is the sum of the solute’s contribution and the solvent’s contribution, which is not always additive. Using a volumetric flask and filling to the mark ensures the final volume is correct.

Related

Formula used
in m | Mass of solute | g | 2.922 | 0
in mm | Molar mass | g/mol | 58.44 | 0.001
in v | Final solution volume | mL | 250 | 0.001
out c | Molarity | mol/L | m / mm / (v / 1000) | 4
out cmm | Concentration in millimolar | mM | c * 1000 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →