This calculator converts a centrifuge speed entered in revolutions per minute (RPM) and a rotor radius into relative centrifugal force (RCF), expressed as multiples of Earth’s gravity (×g). Enter the rotor’s effective radius in centimetres and the RPM shown for your run to get the corresponding RCF; grams alone cannot be converted to RCF because “g” can mean either mass in grams or gravitational force.
Formula
The standard centrifuge conversion is RCF = 1.118 × 10−5 × r × (RPM)2. RCF is a dimensionless ratio, commonly written as ×g; it tells you how many times the acceleration due to Earth’s gravity the sample experiences. In the formula, r is the effective rotor radius in centimetres, RPM is the rotation rate in revolutions per minute, and 1.118 × 10−5 is the conversion constant for those units. The calculator’s second output converts the RCF ratio into acceleration in metres per second squared by multiplying by standard gravity, 9.80665 m/s².
This is not a direct conversion from a mass in grams to RCF. A mass of 5 g, for example, is not enough information to calculate centrifuge force. If “g” means grams, you need the centrifuge’s speed and rotor radius. If “g” means ×g, it already represents RCF and no conversion is needed unless you want acceleration in m/s².
Worked Example
Using the calculator’s default values, RPM = 10,000 and radius = 10 cm:
- Square the speed: (10,000 RPM)² = 100,000,000 RPM².
- Multiply by the radius: 10 cm × 100,000,000 RPM² = 1,000,000,000 cm·RPM².
- Apply the conversion constant: RCF = 1.118 × 10−5 × 1,000,000,000 = 11,180 ×g.
- Convert to acceleration: 11,180 × 9.80665 m/s² = 109,650.407 m/s², or 109,650.41 m/s² to two decimal places.
The headline result is 11,180 ×g. The actual force acting on a sample depends on its mass as well as the acceleration; this calculator reports acceleration relative to gravity, not force in newtons.
Assumptions
- The entered radius is in centimetres and is measured from the axis of rotation to the relevant sample position.
- The entered speed is the rotor’s actual RPM, not a target RCF or a mass in grams.
- The formula treats the sample’s motion as circular rotation at a steady speed. It does not account for acceleration or deceleration during a run.
- The acceleration conversion uses standard gravity, 9.80665 m/s².
When to Use the Conversion
Use this calculation when a protocol specifies RCF but your centrifuge setting is given in RPM, or when comparing settings between rotors. RPM describes how quickly the rotor turns. RCF describes the resulting acceleration at a particular radius. The same RPM can produce different RCF values on rotors with different radii, so RPM settings are not interchangeable between centrifuges.
For a swinging-bucket rotor, the radius changes as the bucket moves from its resting position to its operating position. Use the radius and RCF convention specified by the rotor documentation or your lab method. A maximum-radius value, often measured to the bottom of the sample tube when the bucket is extended, gives a different result from a radius measured to the sample’s midpoint. Keep the measurement point consistent with the protocol.
Read the first result as a multiple of gravity: 500 ×g means an acceleration 500 times standard gravitational acceleration at the selected radius. The second result is the same acceleration in m/s². Neither output states how long to centrifuge; run time, temperature, sample balance, tube suitability and rotor limits must come from the applicable method and equipment instructions.
Step-by-Step
- Check what “g” means. Confirm whether the value you have is grams (mass) or ×g (relative centrifugal force). Grams cannot be converted to RCF on their own.
- Find the rotor speed. Use the RPM specified by the method or the speed readout. Do not enter an RCF value in the RPM field.
- Find the effective radius. Check the rotor or centrifuge documentation for the radius in centimetres and identify whether it refers to the sample’s top, middle or bottom. Use the measurement point required by your method.
- Enter both values. Type RPM as a number of revolutions per minute and radius in centimetres. Convert a radius from millimetres to centimetres by dividing by 10, or from metres to centimetres by multiplying by 100.
- Read the RCF output. Use the first result, in ×g, as the relative force at the radius you entered. Use the m/s² result only when acceleration in SI units is specifically needed.
- Check the setting before use. Confirm that the calculated RCF, speed, tubes and rotor are within the limits and instructions for the equipment and method. Follow your lab method, the safety data sheet (SDS) and your supervisor.
Common Mistakes
- Confusing grams with ×g: A mass in grams is not a centrifuge acceleration. You need RPM and radius to calculate RCF.
- Using the wrong radius unit: The constant in this formula requires centimetres. Entering 0.10 for a 10 cm radius, without converting metres, makes the result 100 times too small.
- Using the wrong rotor radius: The radius is measured from the axis of rotation, not the rotor’s diameter. Do not enter the diameter as if it were a radius.
- Forgetting that speed is squared: Doubling RPM produces four times the RCF at the same radius. A small speed-entry error can therefore make a substantial difference.
- Assuming one RPM value means one RCF: RCF also depends on radius, so the same RPM on two rotor geometries may produce different forces.
- Rounding too early: Retain the full RPM and radius values through the calculation, then round the final result to a sensible number of significant figures.
Tips
- Record both RPM and RCF, along with the rotor and radius convention, so the setting can be checked or reproduced.
- If a method gives RCF and you need RPM, rearrange the formula: RPM = √(RCF ÷ (1.118 × 10−5 × r)), with radius in centimetres.
- Use the calculator’s result as a conversion, not as permission to exceed a rotor’s rated speed or a sample container’s limits.
- For method-critical work, use the radius definition and rounding convention stated in the rotor documentation or protocol; different measurement points can lead to different RCF values.
Troubleshooting
The answer seems 10 or 100 times off: Check whether you entered millimetres or metres while the formula expects centimetres. Convert the radius before entering it, and check that you used radius rather than diameter.
The answer is unexpectedly low or high: Verify the RPM field and make sure it contains revolutions per minute, not a value already expressed as ×g. Because RPM is squared, check for a missing digit or an extra zero.
Your result differs from a centrifuge display: Compare the radius used by the display with the radius you entered. The display may use a defined sample position or a rotor-specific convention. Check the equipment documentation and use the same convention as your method.
You only know the mass in grams: There is not enough information to calculate RCF. Find the required rotor RPM and effective radius. If you already have an RCF value, you do not need to convert it from grams.
Frequently Asked Questions
Can I convert grams directly to RCF?
No. Grams measure mass, while RCF is an acceleration ratio. You need rotor speed in RPM and radius in centimetres.
What is the formula for converting RPM to RCF?
RCF = 1.118 × 10−5 × radius in cm × RPM². The result is expressed as ×g.
Does the same RPM always give the same RCF?
No. At the same RPM, a larger radius produces a higher RCF. Rotor geometry matters.
Should I use the maximum rotor radius?
Use the radius definition required by your method or rotor documentation. The sample position used for the radius must match the convention behind the RCF value.
Is RCF the same as force in newtons?
No. RCF is acceleration relative to gravity. To find force in newtons, you would also need the mass in kilograms and use force = mass × acceleration.
How do I calculate RPM when I know RCF?
Use RPM = √(RCF ÷ (1.118 × 10−5 × radius in cm)). Ensure the RCF is a numeric multiple of gravity, such as 500 for 500 ×g.
Related
Formula used
in rpm | Rotor speed | RPM | 10000 | 0 in r | Rotor radius | cm | 10 | 0.001 out rcf | Relative centrifugal force | ×g | 1.118 * 10^-5 * r * (rpm / 1)^2 | 2 out gms | Relative centrifugal force | m/s² | rcf * 9.80665 | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Isotope Percent Abundance Calculator and How to Use It75.91 %
- Percentage Abundance Calculator and How to Find It
- Isotope Fractional Abundance Calculator and Formula0.2409 fraction
- Percent Abundance Formula: Calculate Isotope Percentages25.00 %
- Isotope Percent Abundance Calculator and How to Use It50.00 %
- Isotope Percent Abundance Calculator and How-To Guide75.91 %