Convert a mass-per-volume concentration (w/v) to molarity by combining the solute’s mass concentration with its molar mass. Enter the mass of solute per stated volume, its molar mass, and the final solution volume; the calculator returns mol/L and mM. Use a concentration and molar mass for the same chemical form, and make sure the volume refers to the final solution.
Formula
First express the w/v concentration as grams of solute per liter of solution. Then divide that mass concentration by the molar mass:
Molarity (mol/L) = mass concentration (g/L) / molar mass (g/mol)
If you have a weighed mass and a final solution volume instead, use:
c = m / [MM × (V / 1000)]
- c is molarity, in mol/L.
- m is solute mass, in grams (g).
- MM is molar mass, in grams per mole (g/mol).
- V is final solution volume, in milliliters (mL). Dividing by 1000 converts mL to L.
- c × 1000 converts mol/L to millimoles per liter (mM).
For a w/v value written as a percentage, x% (w/v) means x grams per 100 mL of final solution. That is 10x g/L, so the equivalent formula is c = (10x) / MM. For example, 5% (w/v) means 50 g/L, not 5 g/L. The calculator uses mass and volume directly; enter the corresponding grams and milliliters to avoid mixing percentage conventions.
Worked Example
Using the calculator’s default values: 2.922 g of solute, a molar mass of 58.44 g/mol, and a final solution volume of 250 mL.
- Convert the volume to liters: 250 mL / 1000 = 0.25000 L.
- Calculate the amount of solute: 2.922 g / 58.44 g/mol = 0.050000 mol.
- Divide amount by final volume: 0.050000 mol / 0.25000 L = 0.2000 mol/L.
- Convert to millimolar: 0.2000 mol/L × 1000 = 200.00 mM.
The result is 0.2000 mol/L, or 200.00 mM. The mass concentration represented by these defaults is 2.922 g / 0.25000 L = 11.688 g/L.
Assumptions
- The volume entered is the final volume of the solution, not the volume of solvent used before dissolving the solute.
- The solute is treated as the stated pure chemical form, and its molar mass matches that form.
- The conversion is arithmetic: it does not assume complete dissociation, a particular temperature, or ideal solution behavior.
What You’ll Need
- A w/v concentration or the mass of solute and final solution volume.
- The correct molar mass for the compound and chemical form.
- Consistent units: grams, grams per mole, and milliliters or liters.
- A calculator, or the calculator above.
Step-by-Step
- Identify what the w/v number means. A percentage labeled % (w/v) is grams per 100 mL of final solution. Other labels may give g/L, mg/mL, or a direct mass and volume. Check the definition rather than assuming all concentration percentages are alike.
- Find the molar mass. Use the formula for the precise compound, including waters of hydration, counterions, or salt form where relevant. Add the atomic masses in the formula, or use a reliable reference value. Do not substitute the molar mass of a related compound.
- Convert the concentration to g/L. For x% (w/v), multiply x by 10. For example, 2% (w/v) becomes 20 g/L. For mg/mL, the numerical value is the same in g/L: 3 mg/mL equals 3 g/L, because both the mass and volume conversion factors are 1000. Convert other units explicitly.
- Divide by molar mass. Use c = concentration in g/L divided by molar mass in g/mol. The grams cancel, leaving mol/L. If starting with a weighed mass, calculate g/L from mass divided by final volume in liters, then divide by molar mass.
- Check the result and report it clearly. Include the unit, mol/L or M, and sensible significant figures. Multiply by 1000 for mM if useful. Avoid implying that the calculation establishes purity, solubility, or the concentration of a reaction mixture after further additions.
For example, if a solution is labeled 2% (w/v) and the compound’s molar mass is 100 g/mol, convert 2% to 20 g/L, then calculate 20 / 100 = 0.20 mol/L. This is a general arithmetic example; the molar mass must be replaced with the value for the actual compound.
Common Mistakes
- Confusing w/v with v/v or w/w. Volume-per-volume and mass-per-mass percentages are different concentration measures; the conversion above applies to mass per volume.
- Using the wrong percentage conversion. x% (w/v) is 10x g/L, not x g/L. Remember that the percentage’s denominator is 100 mL.
- Forgetting the mL-to-L conversion. Molarity is moles per liter. If calculating directly from mass and volume in mL, divide the volume by 1000 before using it in the denominator.
- Using solvent volume instead of final solution volume. Dissolving a solid can change volume. A stated solution concentration refers to the completed solution’s volume.
- Using an incompatible molar mass. Hydrated and anhydrous forms, or a free compound and its salt, can have different molar masses. Match the formula on the label or method.
- Rounding too early. Keep extra digits during unit conversion and division, then round the final value to match the precision of the measurements.
Tips
- Write units beside each number before calculating; the cancellation should leave mol/L.
- Use the direct formula for a percentage: c (mol/L) = 10 × x / MM, where x is the numerical % (w/v) value and MM is in g/mol.
- Check scale with a rough estimate. A few grams per liter divided by a molar mass near 100 g/mol gives a concentration of a few hundredths of a mole per liter.
- Distinguish molarity from molality. Molarity uses liters of solution; molality uses kilograms of solvent and cannot be obtained from w/v alone without additional information.
- For bench work, follow your lab method, the safety data sheet (SDS) and your supervisor.
Troubleshooting
The answer is 1000 times too large or too small: check whether the volume is in mL or L and whether the mass is in g or mg. Convert all inputs to the units required by the formula before calculating.
The result does not match a label: check whether the label uses % (w/v), % (w/w), mg/mL, or another convention. Verify the chemical form and molar mass, and check whether the printed value is rounded.
The calculated concentration seems implausible: recheck the decimal point, the final-volume basis, and the molar mass. A value entered as 250 when the intended volume is 250 mL should not be treated as 250 L.
You only know the percentage and not the total amount prepared: that is enough to calculate molarity if the percentage is explicitly w/v and the molar mass is known. The total batch volume is not needed when using c = 10x / MM.
Frequently Asked Questions
How do I convert % (w/v) directly to molarity?
Multiply the numerical percentage by 10 to get g/L, then divide by molar mass in g/mol: molarity = 10 × % (w/v) / molar mass.
Is 1% (w/v) equal to 1 mol/L?
No. It means 1 g per 100 mL, or 10 g/L. Its molarity depends on the solute’s molar mass.
Can I convert mg/mL to molarity?
Yes. Convert mg/mL to g/L; the numerical value is unchanged. Divide that value by molar mass in g/mol to get mol/L.
Do I need the density of the solution?
Not for a w/v concentration, because it already relates solute mass to solution volume. Density is generally needed for conversions involving mass-per-mass concentration or other bases.
Does molarity change with temperature?
Because solution volume can expand or contract with temperature, molarity can change slightly with temperature. The arithmetic conversion uses the stated volume and does not correct for temperature.
Can this calculation tell me how many particles are present?
It gives moles per liter. Converting moles to particles requires multiplying moles by Avogadro’s constant, and the particle identity depends on whether the solute dissociates or reacts in solution.
Related
Formula used
in m | Mass of solute | g | 2.922 | 0 in mm | Molar mass | g/mol | 58.44 | 0.001 in v | Final solution volume | mL | 250 | 0.001 out c | Molarity | mol/L | m / mm / (v / 1000) | 4 out cmm | Concentration in millimolar | mM | c * 1000 | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- MD Calc I:T Ratio Calculator and Explanation0.0500 ratio
- Oxygen Mass Number: Isotope Values Explained16 nucleons
- Mass-to-Light Ratio: Meaning and Calculation1.000 M☉/L☉
- M/z Ratio in Mass Spectrometry: Meaning and Calculation1,000.00 Th
- Mass Fraction to Molar Fraction Calculator
- K2 Molar Mass Calculator and Calculation78.1966 g/mol