molecalculator

Moles & Molar Mass

How to Determine Enthalpy: Step-by-Step Guide

Calculator No. 01-8110 · Updated · Formula and assumptions shown below

Heat absorbed (q) 2,301.20 J
Enthalpy change (ΔH)
23.01 kJ/mol
= Heat absorbed (q) ÷ 1000 ÷ Moles of reactant
Mass of water
100 g
Set in the form below
Specific heat capacity
4.184 J/(g·°C)
Set in the form below
You enter
Mass of water (g), Specific heat capacity (J/(g·°C)), Temperature change (°C), Moles of reactant (mol)
You get
Heat absorbed (q) (J), Enthalpy change (ΔH) (kJ/mol)
Rounding
2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This guide shows you how to determine the enthalpy change (ΔH) of a reaction, whether you’re working in a lab or solving problems. You’ll learn the two main methods—calorimetry (measuring heat transfer) and Hess’s law (calculating from known reactions)—and how to apply them step by step. By the end, you’ll be able to calculate ΔH with confidence and avoid the usual pitfalls.

Formula

For a reaction at constant pressure (common in lab work), the enthalpy change is calculated using:

q = m × c × ΔT

where:

  • q = heat absorbed or released (in joules, J)
  • m = mass of the substance (usually water) in grams (g)
  • c = specific heat capacity (J/(g·°C)) – for water, 4.184 J/(g·°C)
  • ΔT = temperature change in °C (final minus initial)

Then, to get the enthalpy change per mole of reactant:

ΔH = q / n

where n is the moles of the limiting reactant. ΔH is expressed in kJ/mol, so divide q by 1000.

Worked Example

Suppose you dissolve 0.1 mol of a salt in 100 g of water, and the temperature drops by 5.5 °C. Using the default values from the calculator:

  1. Calculate q: q = 100 g × 4.184 J/(g·°C) × 5.5 °C = 2301.2 J
  2. Convert to kJ: 2301.2 J ÷ 1000 = 2.3012 kJ
  3. Divide by moles: ΔH = 2.3012 kJ ÷ 0.1 mol = 23.01 kJ/mol

So the enthalpy change is approximately 23 kJ/mol (endothermic, since temperature decreased). The calculator gives 23.01 kJ/mol, matching our manual calculation.

Assumptions

  • The specific heat capacity of the solution is approximately that of water (4.184 J/(g·°C)).
  • The density of the solution is approximately 1 g/mL, so mass ≈ volume in mL.
  • The calorimeter absorbs negligible heat (or its heat capacity is accounted for).
  • The reaction goes to completion and the limiting reactant is known.
  • Pressure is constant (typical for open beakers).

What You’ll Need

  • A thermometer or temperature probe (precision ±0.1 °C)
  • A calorimeter (insulated container, e.g., a coffee cup with a lid)
  • A balance to measure mass (if using solids)
  • Graduated cylinder or pipette for volumes
  • Known amounts of reactants (e.g., a salt and water)
  • Stirrer (to ensure uniform temperature)
  • Calculator or the calculator above

Step-by-Step

  1. Identify the reaction and the limiting reactant. Determine which reactant will be completely consumed. This is essential for calculating ΔH per mole.
  2. Measure the mass or volume of the solvent (usually water). If using volume, convert to mass using density (1 g/mL for water).
  3. Record the initial temperature. Let the system equilibrate for a few minutes, then note the temperature (Tinitial).
  4. Add the reactant(s) quickly. For a solid, add it to the water; for a solution, mix the two solutions rapidly. Start stirring immediately.
  5. Monitor the temperature. Record the highest or lowest temperature reached (Tfinal). For exothermic reactions, it rises; for endothermic, it falls.
  6. Calculate ΔT. ΔT = Tfinal − Tinitial. If the reaction is exothermic, ΔT is positive; if endothermic, negative.
  7. Calculate q (heat absorbed by the solution). Use q = m × c × ΔT, where m is the total mass of the solution (water + dissolved solute, if any). For simplicity, often only the water mass is used, but include solute mass for better accuracy.
  8. Convert q to kJ. Divide by 1000.
  9. Determine the moles of the limiting reactant. Use the mass and molar mass: moles = mass / molar mass. For solutions, use concentration × volume (in L).
  10. Calculate ΔH. ΔH = q (in kJ) / moles of limiting reactant. The sign indicates whether the reaction is exothermic (negative) or endothermic (positive).

Common Mistakes

  • Forgetting the sign: If temperature rises, ΔH is negative (heat released). If it falls, ΔH is positive (heat absorbed).
  • Using the wrong mass: The mass in q = mcΔT is the mass of the substance that absorbs heat (usually the solution), not just the solute.
  • Ignoring the heat capacity of the calorimeter: In precise work, the calorimeter itself absorbs heat. For simple coffee-cup setups, this is often neglected, but it introduces error.
  • Not converting units: q is in joules, but ΔH is typically in kJ/mol. Always divide q by 1000.
  • Using the wrong moles: ΔH is per mole of reaction as written. If you use the wrong stoichiometric amount, the value will be off.
  • Assuming ΔT is always positive: For endothermic reactions, ΔT is negative, so q is negative, and ΔH is positive.

Tips

  • Use a calorimeter with a lid to minimize heat loss to the environment.
  • Stir continuously to ensure uniform temperature and accurate readings.
  • For reactions that are slow to reach equilibrium, plot temperature vs. time and extrapolate to the moment of mixing to correct for heat exchange.
  • If you’re using Hess’s law, ensure all reactions are at the same temperature and pressure, and remember to reverse the sign of ΔH when reversing a reaction.
  • Always run a trial with a known reaction (e.g., dissolving NaOH) to check your technique.

Troubleshooting

  • Temperature reading fluctuates: Make sure the thermometer is not touching the bottom of the container and that stirring is consistent.
  • ΔH seems too high or low: Check if you included the mass of the solute in the total mass. Also verify the moles of limiting reactant.
  • Heat loss occurs: If the temperature change is small, heat loss to the surroundings becomes significant. Use a well-insulated calorimeter and work quickly.
  • Reaction doesn’t go to completion: This is rare for simple dissolution, but for other reactions, ensure the limiting reactant is truly limiting and the reaction is fast.
  • Negative mass or temperature: The calculator will show an error if you enter values outside the allowed range. Double-check your inputs.

Frequently Asked Questions

What is the difference between enthalpy and heat?

Enthalpy (H) is a state function representing the total heat content of a system at constant pressure. Heat (q) is energy in transit. ΔH equals q only when pressure is constant and no work other than pressure-volume work is done.

Why do we use the specific heat of water for solutions?

Most reactions in solution are dilute, so the solution’s heat capacity is close to that of water. For more accurate work, you can measure the heat capacity of the actual solution.

Can I determine enthalpy for a reaction that is not in solution?

Yes, you can use bomb calorimetry for combustion reactions at constant volume, which gives internal energy change (ΔU). To convert to ΔH, use ΔH = ΔU + ΔnRT, where Δn is the change in moles of gas.

What is Hess’s law and how does it help?

Hess’s law states that the total enthalpy change for a reaction is the sum of the enthalpy changes for each step, regardless of the path. It allows you to calculate ΔH for reactions that are difficult to measure directly by combining known reactions.

Why is my calculated ΔH different from the literature value?

Experimental errors (heat loss, incomplete reaction, inaccurate measurements) are common. Also, literature values are often at standard conditions (25 °C, 1 atm), while your lab may be at different conditions.

Do I need to account for the heat capacity of the calorimeter?

For precise work, yes. You can determine the calorimeter constant by mixing known hot and cold water and measuring the final temperature. Then add that constant to m×c in the calculation.

Related

Formula used
in m | Mass of water | g | 100 | 0
in c | Specific heat capacity | J/(g·°C) | 4.184 | 0
in dt | Temperature change | °C | 5.5 | -273.15
in n | Moles of reactant | mol | 0.1 | 0
out q | Heat absorbed (q) | J | m * c * dt | 2
out dh | Enthalpy change (ΔH) | kJ/mol | q / 1000 / n | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →