molecalculator

Moles & Molar Mass

Heat of Combustion Formula: How to Find It

Calculator No. 01-10310 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator works out the heat of combustion (enthalpy of combustion, ΔHc) for a fuel or substance using the standard formula based on the masses and temperature change in a calorimetry experiment. You enter the mass of the substance burned, the mass of water (or calorimeter contents) heated, the temperature rise, and the heat capacity of the calorimeter; the calculator returns the heat released per gram and per mole.

Formula

The heat of combustion is the heat released when one mole of a substance burns completely in oxygen under standard conditions. In a bomb calorimeter, the heat released by the burning sample is absorbed by the water and the calorimeter vessel. The basic formula is:

q = (mwater × cwater × ΔT) + (Ccal × ΔT)

where:

  • q = heat released (J or kJ)
  • mwater = mass of water (g)
  • cwater = specific heat capacity of water = 4.184 J/(g·°C)
  • ΔT = temperature rise (°C)
  • Ccal = heat capacity of the calorimeter (J/°C)

Then, to get the heat of combustion per gram: ΔHc (kJ/g) = q / msample

To get it per mole: ΔHc (kJ/mol) = (q / msample) × M

where M is the molar mass of the substance (g/mol).

Worked Example

Suppose you burn 1.000 g of ethanol (M = 46.07 g/mol) in a bomb calorimeter containing 1000 g of water. The temperature rises by 10.5 °C, and the calorimeter has a heat capacity of 50 J/°C.

Step 1: Calculate heat absorbed by water.

qwater = 1000 g × 4.184 J/(g·°C) × 10.5 °C = 43,932 J

Step 2: Calculate heat absorbed by calorimeter.

qcal = 50 J/°C × 10.5 °C = 525 J

Step 3: Total heat released.

q = 43,932 J + 525 J = 44,457 J = 44.46 kJ

Step 4: Heat of combustion per gram.

ΔHc = 44.46 kJ / 1.000 g = 44.46 kJ/g

Step 5: Heat of combustion per mole.

ΔHc = 44.46 kJ/g × 46.07 g/mol = 2048 kJ/mol

The calculator gives the same results: q = 44.46 kJ, qg = 44.46 kJ/g, qm = 2048 kJ/mol.

Assumptions

  • The calorimeter is perfectly insulated (no heat loss to the surroundings).
  • The specific heat capacity of water is constant at 4.184 J/(g·°C) over the temperature range.
  • The heat capacity of the calorimeter (Ccal) is known and constant.
  • The sample burns completely.
  • The temperature rise is measured accurately and uniformly.

When to Use This Formula

Use this formula when you have experimental data from a bomb calorimeter or a simple calorimetry setup and you need to find the heat of combustion of a fuel, food, or other combustible substance. It is also used to compare the energy content of different fuels, to calculate the caloric value of foods, and in thermodynamics problems.

Remember that the result is the enthalpy of combustion at constant volume (bomb calorimeter), which is slightly different from the enthalpy at constant pressure (open flame). For most purposes, the difference is small.

Common Mistakes

  • Unit mix-ups: Forgetting to convert J to kJ, or using grams instead of kilograms. Always keep units consistent.
  • Ignoring the calorimeter heat capacity: The calorimeter itself absorbs heat; neglecting it gives a low result.
  • Using the wrong specific heat: If the liquid is not water, you must use its specific heat capacity, not 4.184.
  • Confusing per gram and per mole: The heat of combustion is usually reported per mole, but many experiments give per gram. Clearly state which you are calculating.
  • Rounding too early: Round only at the end to avoid significant errors.

Tips

  • Use a calibrated thermometer with 0.1 °C precision.
  • Stir the water continuously to ensure uniform temperature.
  • Run a blank (no sample) to correct for any heat from the ignition wire.
  • Use a sample mass that gives a temperature rise of at least 5 °C to reduce relative error.
  • Always determine the calorimeter heat capacity (Ccal) by burning a standard substance like benzoic acid.

Troubleshooting

Result seems too low: Check for incomplete combustion (soot), heat loss, or an underestimated Ccal. Also verify the water mass and temperature rise.

Result seems too high: Check if the sample absorbed moisture, or if the temperature rise was overestimated due to stirring friction.

Negative heat of combustion: This is normal – combustion is exothermic, so ΔH is negative. The calculator returns positive values for the magnitude; report as negative in thermochemical equations.

Calculator shows “Cannot compute”: Ensure all inputs are positive numbers and within the allowed ranges.

Frequently Asked Questions

Q: What is the heat of combustion formula?
A: The basic formula is q = (mwater × cwater × ΔT) + (Ccal × ΔT), where q is heat absorbed by water and calorimeter. Then divide by sample mass to get per gram, and multiply by molar mass to get per mole.

Q: Why is the heat of combustion negative?
A: Combustion releases heat, so the system loses energy. By convention, exothermic reactions have negative ΔH. The magnitude is what we usually quote.

Q: What is the difference between higher and lower heating value?
A: The higher heating value (HHV) includes the heat of condensation of water vapor produced; the lower heating value (LHV) does not. Bomb calorimetry gives HHV.

Q: How do I find the molar mass for the per-mole calculation?
A: Add the atomic masses of all atoms in the chemical formula. For ethanol (C2H5OH): 2×12.011 + 6×1.008 + 15.999 = 46.07 g/mol.

Q: Can I use this formula for any substance?
A: Yes, as long as it burns completely and you know its molar mass. For solids, use a powdered sample to ensure complete combustion.

Q: Do I need a bomb calorimeter?
A> For accurate results, yes. Simple coffee-cup calorimeters lose heat and give lower values. For educational purposes, a simple setup can approximate the heat of combustion.

Related

Formula used
in m | Mass of substance burned | g | 1.000 | 0
in M | Molar mass of substance | g/mol | 46.07 | 0.001
in mw | Mass of water heated | g | 1000 | 0
in dT | Temperature rise | °C | 10.5 | 0
in Cc | Heat capacity of calorimeter | J/°C | 50 | 0
out q | Heat released | kJ | (mw * 4.184 * dT + Cc * dT) / 1000 | 2
out qg | Heat of combustion per gram | kJ/g | q / m | 2
out qm | Heat of combustion per mole | kJ/mol | q / m * M | 1

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →