This calculator estimates the acid dissociation constant, Ka, of a monoprotic weak acid from its initial concentration and measured pH. Enter the concentration in mol/L and pH; it returns Ka and pKa, with the approximation and assumptions made explicit.
Formula
For a monoprotic acid HA in water, HA ⇌ H+ + A−. Its acid dissociation constant is Ka = [H+][A−]/[HA]. If the acid is the only meaningful source of hydrogen ions, [H+] ≈ 10−pH, [A−] ≈ [H+], and [HA] ≈ C − [H+]. Thus Ka ≈ [H+]2/(C − [H+]). The calculator expresses this as Ka = (10−pH)2/(C − 10−pH).
Here, C is the initial analytical concentration of the acid in mol/L; pH is the measured, unitless pH; [H+] and [A−] are equilibrium concentrations in mol/L; and Ka is the concentration-form equilibrium constant, reported here in mol/L. pKa = −log10(Ka) is unitless. Thermodynamic Ka is formally defined using activities and is dimensionless; this calculator uses the usual dilute-solution concentration approximation.
Worked Example
Use the calculator defaults: C = 0.1 mol/L and pH = 2.88. First estimate the hydrogen-ion concentration:
[H+] = 10−2.88 ≈ 0.0013182567 mol/L.
Assuming the acid supplies this hydrogen ion, [A−] ≈ 0.0013182567 mol/L and [HA] ≈ 0.1 − 0.0013182567 = 0.0986817433 mol/L. Therefore:
Ka ≈ (0.0013182567)2/0.0986817433 ≈ 0.0000176126 mol/L, or 1.761 × 10−5 mol/L. Rounded to the calculator’s six decimal places, Ka is 0.000018 mol/L. Then pKa = −log10(0.0000176126) ≈ 4.7540. The displayed pKa is 4.7540.
Assumptions
- The acid is monoprotic and weak, and its dissociation is the only important source of H+.
- The solution is dilute enough that concentration approximates activity.
- Water autoionization and other acids, bases, and dissolved salts have negligible effects.
- The entered pH represents an equilibrium measurement at the solution’s actual temperature. Ka varies with temperature.
What You’ll Need
- The acid’s initial analytical concentration in mol/L, not merely the amount of acid added.
- An equilibrium pH reading for that solution, along with the measurement temperature and any relevant information about other dissolved substances.
- A calculator, or the calculator fields above. If doing bench work, follow your lab method, the safety data sheet (SDS) and your supervisor.
Step-by-Step
- Check that this method applies. Use it for one monoprotic weak acid, such as a simple HA ⇌ H+ + A− system. It is not a general solution for polyprotic acids, mixtures, buffered samples, or solutions containing appreciable added acid or base.
- Find the initial concentration. Enter the acid’s formal concentration before dissociation, in mol/L. If it was prepared from a known amount and brought to a final volume, calculate C = amount in moles ÷ final solution volume in litres. Convert millilitres to litres by dividing by 1000. Do not use the solvent volume if the stated volume is the final solution volume.
- Obtain the pH at equilibrium. Use a suitable, calibrated pH meter or reliable experimental data for the same solution. Record the temperature. A calculated pH for pure water or a different concentration is not a substitute for the sample’s measured equilibrium pH.
- Enter both values. Put C in the concentration field and the measured pH in the pH field. pH has no unit. Do not enter a negative concentration; the concentration must also be greater than the estimated hydrogen-ion concentration for the formula to give a physically meaningful positive denominator.
- Read Ka and pKa. Ka indicates the equilibrium extent of dissociation under the stated conditions; a larger Ka generally means a stronger acid. pKa is the negative base-10 logarithm of Ka, so a lower pKa corresponds to a larger Ka. Keep the displayed precision for calculations, but do not mistake calculator digits for experimental certainty.
- Check whether the approximation is reasonable. Compare the calculated [H+] with C. If it is not small compared with C, the acid is not dissociating only a small fraction, so the weak-acid approximation may be inaccurate. For a better estimate, solve the equilibrium equation without discarding x: Ka = x2/(C − x), where x = [H+] under the same assumptions. For a real sample with significant background ions, use a full equilibrium model and activities.
- Record conditions with the result. Note acid identity, concentration, pH, temperature, and any important salts or buffers. This makes comparisons meaningful: Ka is associated with a particular acid and temperature, while a measured pH also responds to the solution composition.
Common Mistakes
- Confusing pH with concentration: pH is logarithmic. A pH of 3 corresponds to an estimated hydrogen-ion concentration of 0.001 mol/L, not 3 mol/L.
- Using the wrong concentration: Enter the acid’s initial formal concentration, not the estimated equilibrium concentration of HA, and not a stock concentration before dilution.
- Ignoring other sources of H+: Added strong acid, a buffer, dissolved carbon dioxide, or another acid can make pH unsuitable for this simple calculation.
- Applying it to a polyprotic acid: Multiple dissociation steps have separate constants. A single pH and total concentration do not generally identify each Ka using this formula.
- Rounding too early: Keep the unrounded 10−pH value through the calculation. Report sensible significant figures based on the measured pH and concentration.
- Treating concentration-form Ka as universal: Ionic strength and temperature can affect measured behavior. The simplified result is not necessarily the thermodynamic activity-based constant.
Tips
- Check the pH meter calibration and rinse the probe between samples according to its instructions; unstable readings can dominate the uncertainty in Ka.
- Use consistent units. The concentration input is mol/L, not mmol/L; convert millimolar to molar by dividing by 1000.
- For a quick validity check, calculate the ionization fraction α ≈ [H+]/C. If α is a few percent or less, neglecting x in the denominator is often reasonable; if it is larger, use the exact quadratic under the same chemical assumptions.
- Compare results only at similar temperatures and solution conditions. For pH and buffer work, the meter reading is the real check; temperature and ionic strength shift pH.
- When looking up a reference value, confirm the acid identity, temperature, and whether the source reports a thermodynamic constant or a concentration-based conditional value.
Troubleshooting
The calculator shows an error or cannot compute: Check that both fields contain numbers, concentration is positive, and C is greater than 10−pH. If the latter is not true, the assumed acid-only model is inconsistent with the entered data; do not force a result by changing values without evidence.
Ka is negative or implausibly large: A negative value indicates the denominator or inputs violate the model. A large value can result from substantial dissociation, a pH affected by another solute, or an incorrect concentration. Recheck the sample identity and units, then use the exact equilibrium expression or a more complete model if appropriate.
Repeated pH readings disagree: Allow the reading to stabilize, verify calibration, check for contamination, and measure at a controlled temperature. If the sample is buffered or has appreciable ionic strength, a simple concentration-based estimate may not match a tabulated thermodynamic Ka.
Your result differs from a reference: Confirm that both values refer to the same acid, temperature, and convention. Also check whether the reference gives pKa rather than Ka; convert with Ka = 10−pKa.
Frequently Asked Questions
What does Ka tell me?
Ka describes the equilibrium dissociation of an acid in water. A larger Ka means greater dissociation at equilibrium under comparable conditions.
How do I find Ka from pH alone?
You generally cannot. You also need the initial acid concentration and a model that accounts for what else is in the solution.
Can I calculate Ka from pKa?
Yes. Use Ka = 10−pKa. For example, pKa = 4 gives Ka = 1 × 10−4 in the corresponding concentration convention.
What if the acid is diprotic?
It has separate constants for its first and second dissociation steps. Use a species-distribution or equilibrium calculation with enough information; this single-step calculator is not sufficient.
Does Ka change with concentration?
The thermodynamic Ka is defined for a given temperature, but concentration-based estimates can vary with ionic strength and non-ideal behavior. Dilute-solution assumptions make the simple calculation most useful.
Why is my measured pH different from the value predicted using a tabulated Ka?
Temperature, activity effects, impurities, calibration, and other dissolved species can shift pH. Compare conditions and use the measured pH as the check for the actual sample.
Related
Formula used
in c | Initial acid concentration | mol/L | 0.1 | 0 in p | Measured pH | - | 2.88 | 0 out k | Ka | mol/L | (10 ^ (0 - p)) ^ 2 / (c - 10 ^ (0 - p)) | 6 out pk | pKa | - | 0 - log10(k) | 4
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- MD Calc I:T Ratio Calculator and Explanation0.0500 ratio
- Oxygen Mass Number: Isotope Values Explained16 nucleons
- Mass-to-Light Ratio: Meaning and Calculation1.000 M☉/L☉
- M/z Ratio in Mass Spectrometry: Meaning and Calculation1,000.00 Th
- Mass Fraction to Molar Fraction Calculator
- K2 Molar Mass Calculator and Calculation78.1966 g/mol