molecalculator

Moles & Molar Mass

POH from KB: Calculate Hydroxide Concentration

Calculator No. 01-2472 · Updated · Formula and assumptions shown below

pOH 2.8724
Approximate hydroxide concentration
0.001342 mol/L
Result, rounded to 6 decimal places
Base dissociation constant Kb
0.000018
Set in the form below
Initial base concentration C
0.1 mol/L
Set in the form below
You enter
Base dissociation constant Kb, Initial base concentration C (mol/L)
You get
pOH, Approximate hydroxide concentration (mol/L)
Rounding
4 dp · 6 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Calculate pOH from the base dissociation constant, Kb, and the base concentration, C. Enter Kb as a dimensionless equilibrium constant and C in mol/L; the calculator returns pOH using the weak-base approximation. This method assumes a dilute aqueous solution at 25 °C and is most useful when the base ionizes only slightly.

Formula

For the equilibrium B + H2O ⇌ BH+ + OH−, the base dissociation constant is Kb = [BH+][OH−]/[B]. If the initial base concentration is C and the amount that reacts is x, then Kb = x2/(C − x). When x is small compared with C, approximate C − x as C, giving [OH−] ≈ x ≈ √(KbC).

Then pOH = −log10([OH−] in mol/L relative to the standard concentration of 1 mol/L). In the calculator, Kb is dimensionless, C is in mol/L, and the approximate hydroxide concentration is √(Kb × C). The logarithm is taken of the numerical concentration expressed in mol/L; pOH itself is dimensionless. For a solution at 25 °C, pH + pOH = 14.00, but pOH can be calculated without calculating pH.

Worked Example

Using the default values, Kb = 1.8 × 10−5 and C = 0.1 mol/L:

  1. Estimate hydroxide concentration: [OH−] ≈ √(KbC) = √((1.8 × 10−5) × 0.1) = √(1.8 × 10−6) ≈ 0.00134164 mol/L.
  2. Calculate pOH: −log10(0.00134164) ≈ 2.8723.

The calculator displays pOH as 2.8723 and approximate [OH−] as 0.001342 mol/L when rounded to its stated decimal places.

Assumptions

  • The base is in dilute aqueous solution, and the equilibrium is represented by one base-ionization step.
  • The weak-base approximation assumes the change in base concentration is small compared with its initial concentration.
  • For a pH conversion using pH + pOH = 14.00, assume 25 °C. The ion product of water changes with temperature.
  • Kb should correspond to the same temperature and chemical species as the solution being considered.

What You’ll Need

  • The base’s Kb value at the relevant temperature, obtained from a reliable reference or supplied by your course or lab method.
  • The initial analytical concentration of the base in mol/L.
  • A calculator, spreadsheet, or this page’s calculator. If preparing or measuring a solution, follow your lab method, the safety data sheet (SDS) and your supervisor.

Step-by-Step

  1. Identify the base and its equilibrium. Write the base-ionization reaction and check that the Kb value applies to that base. A polybasic species may have more than one ionization step; use the constant for the step relevant to the question.
  2. Find Kb for the correct conditions. Use a value at the solution’s temperature if available. Kb is an equilibrium constant, not a concentration, and it has no unit in the usual dilute-solution convention. Do not substitute pKb directly: if a reference gives pKb, convert it using Kb = 10−pKb.
  3. Enter the initial base concentration. Use the starting analytical concentration C in mol/L, not the concentration of hydroxide and not a value in mmol/L. Convert units first; for example, 10 mmol/L is 0.010 mol/L.
  4. Calculate the approximate hydroxide concentration. The calculator evaluates √(KbC). This estimates how much hydroxide the base produces at equilibrium under the weak-base approximation.
  5. Take the negative base-10 logarithm. The result is pOH = −log10([OH−]). A smaller hydroxide concentration gives a larger pOH; do not omit the minus sign.
  6. Check whether the approximation is appropriate. Estimate the fraction ionized, x/C, using the calculated x = [OH−]. If this is not small, solve the full equilibrium equation rather than relying on the square-root shortcut. A common screening rule is that the approximation is usually reasonable when x/C is at most about 5%; treat this as a check, not a universal guarantee.
  7. Report the result with context. State the base, Kb, concentration, temperature assumption, and whether pOH is approximate. Keep sensible significant figures; extra calculator digits do not make the input data more precise.

Common Mistakes

  • Entering pKb as Kb: pKb is a logarithmic value. Convert it to Kb = 10−pKb before entering it.
  • Mixing units: the concentration input must be mol/L. Entering a value in mmol/L without dividing by 1,000 makes the calculated concentration wrong.
  • Using the wrong concentration: enter the initial base concentration, not the final hydroxide concentration or the amount of solvent used.
  • Ignoring the approximation: √(KbC) assumes x is small relative to C. Stronger bases or very dilute solutions may not meet this condition.
  • Confusing pOH and pH: pOH describes hydroxide concentration. At 25 °C, pH = 14.00 − pOH; this relation is temperature-dependent.
  • Rounding too early: retain unrounded values through the square root and logarithm, then round the reported answer to match the precision of the inputs.

Tips

  • Keep Kb and concentration in scientific notation when values are very small; this reduces powers-of-ten mistakes.
  • Check the order of magnitude: for a weak base, the hydroxide concentration should generally be lower than the starting base concentration.
  • If a reference supplies pKb, keep the conversion visible in your working so it is clear which value was entered.
  • When comparing results from different sources, verify temperature, concentration convention, and whether the reported value is experimental or tabulated.
  • Use an equilibrium-table calculation or a suitable numerical solver if the approximation check fails, rather than forcing the shortcut to fit.

Troubleshooting

The answer is negative or unexpectedly large: check that Kb is positive and that you entered Kb, not pKb. Confirm that C is positive and in mol/L, then check for a misplaced decimal point.

The calculated hydroxide concentration is close to or greater than C: the weak-base approximation is not valid for those inputs. Solve Kb = x2/(C − x) using the physically meaningful root, or use a full equilibrium calculation that includes water when necessary.

Your pH-derived pOH disagrees: confirm the temperature and the pH measurement conditions. The simple pH + pOH = 14.00 relationship applies at 25 °C; temperature and solution non-ideality can alter the comparison.

The reference gives a different Kb: check that it refers to the same base form, temperature, and equilibrium step. Do not average conflicting constants without understanding why they differ.

Frequently Asked Questions

Can I calculate pOH from Kb alone?
No. This approximation also needs the initial base concentration. The same base can produce different pOH values at different concentrations.

What if I have pKb instead of Kb?
Convert it first: Kb = 10−pKb. Then enter the resulting dimensionless Kb value.

Does this method work for strong bases?
Not reliably. The square-root approximation is intended for weak-base equilibrium where ionization is small relative to the initial concentration. Strong bases require a different treatment.

Can I get pH from the result?
At 25 °C, use pH = 14.00 − pOH. At other temperatures, use the appropriate water ion-product value rather than assuming 14.00.

Why is my measured pOH different?
Real solutions can depart from the ideal dilute approximation, and temperature, other dissolved substances, measurement calibration, and activity effects can matter. Use the measurement as the practical check when measurement is required.

What does a very small Kb mean?
It indicates that the base ionizes only weakly under the conditions represented by that equilibrium constant. It does not by itself determine pOH; concentration is needed too.

Related

Formula used
in kb | Base dissociation constant Kb | - | 1.8e-5 | 0
in c | Initial base concentration C | mol/L | 0.1 | 0
out poh | pOH | - | -log10(sqrt(kb * c)) | 4
out oh | Approximate hydroxide concentration | mol/L | sqrt(kb * c) | 6

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →