molecalculator

Moles & Molar Mass

How to Find V1 and V2 in Dilution Calculations

Calculator No. 01-8109 · Updated · Formula and assumptions shown below

Solved value 100.0000 mL or mol/L
Initial concentration (C1)
5 mol/L
Set in the form below
Initial volume (V1)
10 mL
Set in the form below
Final concentration (C2)
0.5 mol/L
Set in the form below
Final volume (V2)
100 mL
Set in the form below
You enter
Initial concentration (C1) (mol/L), Initial volume (V1) (mL), Final concentration (C2) (mol/L), Final volume (V2) (mL)
You get
Solved value (mL or mol/L)
Rounding
4 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator determines the two unknown volumes in a dilution problem: V1 (the volume of stock solution needed) and V2 (the final total volume after adding solvent). You enter three of the four values from the dilution equation C1V1 = C2V2, and the calculator solves for the missing one. This is the standard method for preparing a solution of lower concentration from a more concentrated stock.

Formula

The core relationship is the dilution equation:

C1 × V1 = C2 × V2

Where:

  • C1 = concentration of the stock (initial) solution, in mol/L (molarity)
  • V1 = volume of the stock solution taken, in mL
  • C2 = concentration of the diluted (final) solution, in mol/L
  • V2 = total final volume of the diluted solution, in mL

To solve for any single variable, rearrange the equation:

  • V1 = (C2 × V2) / C1
  • V2 = (C1 × V1) / C2
  • C1 = (C2 × V2) / V1
  • C2 = (C1 × V1) / V2

The calculator above uses the same logic: it computes the missing value from the three inputs you provide. If you leave one input blank (set to 0), the result shows the solved value for that blank. The default values solve for V1 when C1 = 5.00 mol/L, V2 = 100 mL, and C2 = 0.500 mol/L.

Worked Example

Using the default values: you have a 5.00 mol/L stock solution and need 100 mL of a 0.500 mol/L solution. Find V1.

Step 1: Write the equation: C1V1 = C2V2

Step 2: Substitute the known values: (5.00 mol/L) × V1 = (0.500 mol/L) × (100 mL)

Step 3: Multiply the right side: 0.500 × 100 = 50.0 (units: mol/L × mL)

Step 4: Divide both sides by 5.00: V1 = 50.0 / 5.00 = 10.0 mL

So you need 10.0 mL of the 5.00 mol/L stock, diluted to a final volume of 100 mL with solvent.

Assumptions

  • The volumes are additive (no significant volume change on mixing).
  • Concentrations are in the same units on both sides (e.g., both mol/L, both % w/v, or both mg/mL).
  • The solution is ideal and temperature is constant.
  • You are diluting with pure solvent, not adding more solute.

When to Use This

This calculation appears in nearly every lab prep: making a working solution from a concentrated stock, preparing serial dilutions, or adjusting a solution to a desired concentration. It also works for any concentration unit as long as both C1 and C2 use the same unit. The equation does not care whether you use molarity, percent, or mass per volume—just keep both sides consistent.

How to Read the Result

The result tells you the missing value. If you left V1 blank, the result is the volume of stock to pipette. If you left V2 blank, the result is the total final volume to make (so you add solvent up to that mark). If you left C1 or C2 blank, the result is the concentration in the same unit you entered for the other concentration. Always check that the answer makes physical sense: diluting a solution should give C2 < C1, and V2 > V1.

Common Mistakes

  • Mixing units: Using mol/L for C1 but mg/mL for C2. Convert everything to the same concentration unit first.
  • Volume vs. solvent added: V2 is the final total volume, not the amount of solvent to add. If you need 100 mL final and use 10 mL stock, you add 90 mL solvent, not 100 mL.
  • Forgetting to rearrange: Plugging numbers into the wrong form. Always solve for the unknown symbolically before substituting.
  • Ignoring significant figures: The result should have no more significant figures than the least precise input.
  • Using the wrong V1: V1 is the volume of the concentrated stock taken, not the volume of solvent.

Tips

  • Write the equation with units attached to every number. Units will tell you if you have the formula upside down.
  • For serial dilutions, apply the equation step by step, using the previous dilution’s output as the next input.
  • When preparing a solution, always add the stock first, then bring up to the final volume with solvent. This avoids overshooting V2.
  • Use a volumetric flask for V2 when precise concentration matters; graduated cylinders are for rough work.
  • If your stock concentration is in a different unit (e.g., % w/v), convert to mol/L or keep the same unit on both sides—never mix.

Troubleshooting

Result seems too large or too small: Recheck which value you left blank. If you left V1 blank and got 1000 mL, that means your stock is more dilute than your target—impossible for a true dilution. Double-check C1 and C2 order.

Getting a negative number: Negative volumes or concentrations are physically impossible. This usually means you entered a concentration that is higher after dilution (C2 > C1). Swap the values or re-read the problem.

Units do not cancel: If you enter C1 in mol/L and C2 in mmol/L, the equation will give nonsense. Convert mmol/L to mol/L by dividing by 1000 before calculating.

Calculator shows an error: Ensure all inputs are positive numbers. Zero is treated as the unknown to solve for, so only leave one input at zero.

Frequently Asked Questions

Q: Can I use this for percent solutions?
A: Yes, as long as both concentrations use the same unit (e.g., both % w/v). The equation is unit-agnostic.

Q: What if I need to find the amount of solvent to add?
A: Subtract V1 from V2. Solvent to add = V2 − V1. For the example above, that’s 100 − 10 = 90 mL.

Q: Does temperature affect the calculation?
A: Yes, because volume changes with temperature. For precise work, prepare solutions at the same temperature the equation assumes (usually 25 °C).

Q: What if my stock is a solid, not a solution?
A: This equation is for diluting an existing solution. For a solid, you need to calculate mass from molar mass and desired moles, not use V1.

Q: Why is V2 larger than V1 in a dilution?
A: Because you are adding solvent. The total volume increases while the amount of solute stays constant, which lowers concentration.

Q: Can I use this for serial dilutions?
A: Yes, but apply it repeatedly. For a 1:10 serial dilution, each step uses C1 = previous concentration, V1 = 1 part, V2 = 10 parts.

Related

Formula used
in c1 | Initial concentration (C1) | mol/L | 5.00 | 0
in v1 | Initial volume (V1) | mL | 10 | 0
in c2 | Final concentration (C2) | mol/L | 0.500 | 0
in v2 | Final volume (V2) | mL | 100 | 0
out result | Solved value | mL or mol/L | (c1*v1)/(c2) | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →