This guide explains the process of transcribing messenger RNA (mRNA) from a DNA template, a fundamental technique in molecular biology. You will learn the purpose of transcription, the required components, and a step-by-step protocol to produce mRNA in a test tube. This is a practical walkthrough for educational and lab settings, not a clinical procedure.
What You’ll Need
- DNA template (linearized plasmid or PCR product) containing your gene of interest with a promoter sequence (e.g., T7, SP6, T3)
- RNA polymerase (matching your promoter, e.g., T7 RNA polymerase)
- NTP mix (ATP, CTP, GTP, UTP) – each at 10 mM or as per kit instructions
- Transcription buffer (usually 10×, containing MgCl₂ and salts)
- Dithiothreitol (DTT) – often included in buffer or added separately to 10 mM final
- RNase inhibitor (e.g., human placental ribonuclease inhibitor)
- Nuclease-free water
- DNase I (to remove template after transcription)
- Pipettes and sterile, nuclease-free microcentrifuge tubes
- Thermal cycler or water bath set to 37 °C (for T7 polymerase)
- Ice bucket
- Optional: RNA purification kit or spin column, agarose gel for analysis
Step-by-Step
- Prepare the DNA template. Ensure your DNA is linear and ends with a promoter sequence recognized by your RNA polymerase. If using a plasmid, linearize it with a restriction enzyme that cuts downstream of your insert (not within it). Purify the linearized DNA and quantify it; you will need 1–2 μg per reaction.
- Thaw and mix reagents. Thaw all frozen components on ice. Gently vortex and briefly centrifuge each tube to collect contents. Keep everything on ice while setting up the reaction.
- Assemble the transcription reaction. In a nuclease-free tube, add the following in order (volumes for a 20 μL reaction): nuclease-free water (to final volume), 2 μL of 10× transcription buffer, 2 μL of 10 mM DTT (if not in buffer), 1 μL of RNase inhibitor (20 U), 1–2 μg of DNA template, 2 μL of each NTP (10 mM each, final concentration 1 mM each), and 1 μL of T7 RNA polymerase (20 U). Mix gently by pipetting, do not vortex.
- Incubate the reaction. Place the tube in a thermal cycler or water bath set to 37 °C. Incubate for 2–4 hours. For longer transcripts (>1 kb), 4 hours is typical; for shorter ones, 2 hours may suffice. Do not exceed 6 hours to avoid degradation.
- Remove the DNA template. After incubation, add 1 μL of DNase I (2 U) to the reaction and incubate at 37 °C for 15 minutes. This digests the DNA template, leaving only the RNA.
- Purify the mRNA. Purify the RNA using a commercial RNA cleanup kit or by phenol-chloroform extraction followed by ethanol precipitation. Resuspend the final pellet in nuclease-free water. Quantify by UV absorbance (A260) and check integrity on a denaturing agarose gel.
Common Mistakes
- Using a supercoiled plasmid without linearization. RNA polymerase can transcribe beyond the gene, producing run-on transcripts with incorrect ends.
- Forgetting to include a promoter. The polymerase will not initiate without its specific promoter sequence upstream of your gene.
- RNase contamination. Skin, dust, and non-sterile plastic contain RNases that degrade RNA. Always use gloves, nuclease-free tubes, and filter tips.
- Incorrect NTP concentrations. Too little NTP limits yield; too much can inhibit polymerase. Stick to the recommended 1 mM each.
- Skipping DNase treatment. Residual DNA will interfere with downstream applications and quantification.
Tips
- Use a high-yield transcription kit if you need large amounts of RNA; they often include optimized buffers and higher NTP concentrations.
- Add a 5′ cap analog (e.g., m7G(5′)ppp(5′)G) at a 4:1 ratio to GTP if you need capped mRNA for translation studies.
- Include a short poly(A) tail in your DNA template (or use a tailing kit) if you need mRNA for eukaryotic expression.
- Always run a negative control without polymerase to check for DNA contamination in your reagents.
- Keep all reagents and reactions on ice except during incubation to minimize degradation.
Troubleshooting
Low yield or no RNA: Check that your DNA template is pure and contains the correct promoter sequence. Verify the polymerase is active (store at -20 °C, avoid repeated freeze-thaw). Increase incubation time up to 6 hours, or increase enzyme amount.
RNA is degraded (smear on gel): This is almost always RNase contamination. Clean your workspace with RNase decontamination solution, use fresh gloves, and ensure all reagents are RNase-free. Add more RNase inhibitor.
RNA is shorter than expected: The polymerase may be stopping prematurely due to secondary structures in the template. Lower the incubation temperature to 30 °C (some polymerases work well at 30–37 °C) or add more enzyme. Also check that the template is not nicked.
RNA is longer than expected: The plasmid was not fully linearized or the cut was outside the desired region. Re-linearize with a restriction enzyme that cuts downstream of the gene, and run a gel to confirm linearization.
Precipitate in the reaction after incubation: This is often pyrophosphate, a byproduct of NTP incorporation. It is normal and does not affect RNA yield; just avoid pipetting the precipitate when purifying.
Frequently Asked Questions
Q: Can I use genomic DNA as a template?
A: Yes, but you need to include a promoter sequence upstream of your gene. Genomic DNA is long and may contain introns; for mRNA, you typically use cDNA (without introns) for prokaryotic expression.
Q: What is the difference between transcription and reverse transcription?
A: Transcription synthesizes RNA from DNA (DNA → RNA), while reverse transcription synthesizes DNA from RNA (RNA → DNA), using the enzyme reverse transcriptase.
Q: Why do I need a 5′ cap on mRNA?
A: The 5′ cap is essential for mRNA stability and efficient translation in eukaryotic cells. It protects the RNA from exonucleases and helps ribosome binding.
Q: How do I know my RNA is the correct size?
A: Run an aliquot on a denaturing agarose gel (e.g., formaldehyde gel) alongside an RNA ladder. The band should be at the expected size of your transcript.
Q: Can I store the RNA after transcription?
A: Yes, store at -20 °C for short-term (weeks) or -80 °C for long-term. Avoid repeated freeze-thaw cycles; aliquot into single-use portions.
Q: What is the typical yield from a standard transcription reaction?
A: A standard 20 μL reaction with T7 polymerase typically yields 50–200 μg of RNA, depending on transcript length and template quality. High-yield kits can produce more.
Related
General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.
More in this section
- Normality to g/L Converter & Formula29.220 g/L
- Normality to meq/mL Conversion Calculator1.0000 meq/mL
- Normality Test Q-Q Plot: How to Read It
- Normality Test Results: How to Analyze Them
- Normality Slay the Spire?
- Normality Test for Paired t Test: How to Check