molecalculator

Moles & Molar Mass

Inches WC to PSI Calculator & Conversion Guide

Calculator No. 01-11933 · Updated · Formula and assumptions shown below

Pressure (psi) 1.0000 psi
Pressure (inches of water column)
27.6799 in WC
Set in the form below
You enter
Pressure (inches of water column) (in WC)
You get
Pressure (psi) (psi)
Rounding
4 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator converts pressure from inches of water column (in WC, also written as inH₂O or “inches WC”) to pounds per square inch (psi). You enter the pressure in inches of water column, and the calculator returns the equivalent pressure in psi, using the standard conversion factor 1 psi = 27.6799 in WC. The result is shown with four decimal places for precision.

Formula

The conversion uses a fixed relationship between the two units: 1 pound per square inch (psi) equals 27.6799 inches of water column (in WC) at 39.2 °F (4 °C), the temperature at which water has its maximum density. The formula is:

psi = in WC ÷ 27.6799

Where:

  • in WC – the pressure expressed in inches of water column (inH₂O). This is the height of a column of water that the pressure would support.
  • psi – the pressure expressed in pounds per square inch.
  • 27.6799 – the conversion factor, derived from the density of water and the acceleration due to gravity.

If you need the reverse (psi to in WC), multiply psi by 27.6799.

Worked Example

Using the default input of 27.6799 in WC:

  1. Start with the pressure: 27.6799 in WC.
  2. Divide by the conversion factor: 27.6799 ÷ 27.6799 = 1.0000.
  3. Result: 1.0000 psi.

This matches the calculator output exactly, confirming that 27.6799 in WC is precisely 1 psi.

Assumptions

  • The conversion factor is based on water at 39.2 °F (4 °C), where water density is 62.4 lb/ft³.
  • The gravitational acceleration is taken as 32.174 ft/s² (standard gravity).
  • The conversion is linear and independent of temperature for most practical purposes; at room temperature (68 °F), the factor changes by less than 0.1%.
  • This is a unit conversion, not a physical measurement—it does not account for gauge vs. absolute pressure unless you specify.

When to Use Inches WC vs. PSI

Inches of water column is a low-pressure unit commonly used in HVAC (heating, ventilation, and air conditioning), gas piping, and low-pressure pneumatic systems. For example, natural gas appliance pressures are often specified in inches WC (e.g., 7 in WC for a typical residential gas supply). PSI is more common for higher pressures, such as tire pressure (30-35 psi), hydraulic systems, or compressed air lines (90-150 psi).

You’ll need this conversion when:

  • Reading a manometer that measures in inches WC but your equipment spec requires psi.
  • Comparing pressure ratings from different manufacturers that use different units.
  • Converting gas pressure readings from a U-tube manometer to psi for a pressure gauge.

How to Read the Result

The result is the pressure in psi. For example, if you enter 14 in WC (a common gas appliance pressure), the calculator returns 0.5058 psi. That’s a very low pressure—less than 1 psi. In contrast, 27.6799 in WC equals exactly 1 psi, and 55.3598 in WC equals 2 psi. Because in WC is a fine-grained unit, it’s useful for measuring small pressure differences where a psi would be too coarse.

When reading the result, keep in mind that psi is a larger unit than in WC. A value of 1 psi is about 27.68 inches of water column. So if you’re used to seeing pressures like 0.5 psi, that’s about 13.8 in WC.

Common Mistakes and Misconceptions

  • Using the wrong conversion factor: Some sources round to 27.7 or 28. For most work, 27.68 is fine, but for precision use 27.6799. The difference is less than 0.1%.
  • Confusing in WC with inches of mercury (inHg): 1 inHg is about 13.6 times larger than 1 in WC. A common error is treating them as equal.
  • Forgetting that the conversion is temperature-dependent: The factor changes slightly with water temperature. At 68 °F, 1 psi equals about 27.7 in WC, but at 32 °F it’s 27.7 as well—the variation is small enough to ignore for most applications.
  • Mixing absolute and gauge pressure: This conversion works for both gauge and absolute pressure as long as you’re consistent. It doesn’t add atmospheric pressure.

Practical Context: Gas Appliances and HVAC

In the HVAC and gas industry, inches WC is the standard unit for low-pressure gas. For instance, a typical natural gas manifold pressure for a residential furnace is 3.5 in WC (about 0.126 psi). A propane gas appliance might use 11 in WC (about 0.397 psi). These low pressures are easier to measure with a manometer in inches WC than in psi, which is why the unit persists.

When working with such systems, always follow the manufacturer’s specifications and local codes. If a pressure reading seems off, double-check the unit conversion. A reading of 2 psi is about 55.36 in WC, which is much higher than typical gas appliance pressures—so if you see a number like that, there’s likely a problem.

Frequently Asked Questions

How many inches WC is 1 psi?
Exactly 27.6799 inches of water column at 39.2 °F. For quick mental math, you can use 27.68 in WC per psi.

Can I use this calculator for absolute pressure?
Yes, the conversion is linear and works for both gauge and absolute pressure. Just make sure you’re consistent: if you enter an absolute pressure in in WC, the result is absolute psi. Most pressure gauges read gauge pressure, so check your instrument.

Why do some sources say 1 psi = 27.7 in WC?
They’re rounding the exact value of 27.6799 to one decimal place. For most practical purposes, 27.7 is close enough, but for precise engineering calculations, use the full factor.

What is the difference between in WC and inH₂O?
None—they’re two abbreviations for the same unit: inches of water column. You’ll also see “in H2O” or “in. H2O”. All mean the same thing.

Is this conversion affected by altitude?
No, the conversion factor is based on water density and gravity, which are essentially constant at any altitude for practical purposes. However, atmospheric pressure itself changes with altitude, but that’s a separate measurement—this calculator just converts units.

Can I convert psi to inches WC with the same calculator?
Not directly, but you can use the reverse formula: multiply psi by 27.6799 to get in WC. For example, 0.5 psi × 27.6799 = 13.84 in WC.

Related

Formula used
in inwc | Pressure (inches of water column) | in WC | 27.6799 | 0 | 10000
out psi | Pressure (psi) | psi | inwc / 27.6799 | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →