molecalculator

Moles & Molar Mass

Is h an Electron? The Letter vs the Particle

Calculator No. 01-9694 · Updated · Formula and assumptions shown below

Molarity 0.2000 mol/L
Concentration in millimolar
200.00 mM
= Molarity × 1000
Mass of solute
2.922 g
Set in the form below
Molar mass
58.44 g/mol
Set in the form below
You enter
Mass of solute (g), Molar mass (g/mol), Final solution volume (mL)
You get
Molarity (mol/L), Concentration in millimolar (mM)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The short answer is no: h is not an electron. In chemistry and physics, h is the symbol for the hydrogen atom or the Planck constant (depending on context), while the electron is represented by e⁻. This confusion is common because hydrogen’s atomic symbol is H, and the electron’s symbol contains an “e,” but they refer to entirely different things — one is a subatomic particle, the other is either an element or a physical constant.

Formula

The calculator above works out molarity, the standard measure of solution concentration. The formula is:

c = m / (M × V)

where:

  • c = molarity (mol/L)
  • m = mass of solute (g)
  • M = molar mass of solute (g/mol)
  • V = final solution volume (L, converted from mL by dividing by 1000)

This is the defining equation for molarity. It assumes the solute is fully dissolved and the volume is the final total volume of the solution, not the volume of solvent added.

Worked Example

Using the default values from the calculator: 2.922 g of sodium chloride (NaCl, molar mass 58.44 g/mol) dissolved to a final volume of 250 mL.

  1. Convert volume to liters: 250 mL / 1000 = 0.250 L
  2. Calculate moles of solute: 2.922 g / 58.44 g/mol = 0.05000 mol
  3. Divide moles by volume: 0.05000 mol / 0.250 L = 0.2000 mol/L

The calculator shows 0.2000 mol/L, and in millimolar: 0.2000 × 1000 = 200.00 mM. This matches exactly.

Assumptions

  • The solute is pure and fully dissolves.
  • The volume entered is the final solution volume, not the solvent volume.
  • Temperature effects on volume are ignored (dilute aqueous solutions at room temperature).
  • The molar mass is the formula weight of the anhydrous compound.

When to Use Molarity

Molarity is the default concentration unit in chemistry labs. You use it whenever you need to know how many moles of a substance are in a liter of solution — for stoichiometry, preparing buffers, diluting stock solutions, or calculating reaction yields. For example, if a reaction requires 0.1 mol of NaCl and you have a 0.2000 M solution, you would measure out 0.1 / 0.2000 = 0.5 L (500 mL).

This calculator is useful for making solutions from a solid reagent. You weigh the solid, dissolve it in a portion of solvent, then add solvent to reach the final volume. The key distinction: molarity uses final volume, not solvent volume. If you add 250 mL of water to 2.922 g of NaCl, the final volume will be slightly more than 250 mL because the salt adds its own volume, so the concentration would be slightly lower than 0.2000 M.

How to Read the Result

The first output, molarity in mol/L, is the headline number. A result of 0.2000 mol/L means there are 0.2000 moles of solute particles per liter of solution. The second output, millimolar (mM), is simply the same value multiplied by 1000 — useful because many lab reagents are used at millimolar concentrations. A 200 mM solution is the same as 0.2000 M; they are two ways of writing the same concentration.

When you see a molarity value, always check the unit. A mistake between mol/L and mmol/L is a factor of 1000, which will ruin a buffer or a reaction. The calculator shows both to help you cross-check.

Common Mistakes

  • Using solvent volume instead of final volume: This is the most common error. Always dissolve the solute in less solvent, then top up to the final mark.
  • Unit mix-ups: Forgetting to convert mL to L. 250 mL is 0.250 L, not 250 L. The calculator does this conversion for you, but you must enter the volume in mL.
  • Wrong molar mass: Using the mass of a hydrated salt (like CuSO₄·5H₂O) without including the water of hydration. The molar mass input must match the exact compound you weighed.
  • Rounding too early: If you round 2.922 / 58.44 to 0.05 before dividing by 0.250, you still get 0.2, but with other numbers early rounding can shift the last significant figure.

Limits of the Formula

This molarity formula is exact for ideal solutions, but real solutions deviate at high concentrations. At very high solute loads, the volume of the solute itself becomes non-negligible, and intermolecular interactions change the effective concentration. For most teaching labs and routine preparations below about 1 M, the error is small. The formula also assumes the solute is non-volatile and does not react with the solvent. For precise work, you would use molality (moles per kg of solvent) instead, because molality is temperature-independent, whereas molarity changes as the solution expands or contracts with temperature.

Follow your lab method, the safety data sheet (SDS) and your supervisor for any bench work.

Frequently Asked Questions

Is molarity the same as concentration?

Molarity is one specific way to express concentration — moles of solute per liter of solution. Concentration is the general term for how much solute is in a given amount of solvent or solution. Other units include molality, percent by mass, and parts per million. Molarity is the most common in chemistry because it directly relates to mole ratios in reactions.

What if I only have the mass of the solvent, not the solution volume?

Then you need molality, not molarity. Molality is moles of solute per kilogram of solvent. To convert between them you need the solution density. This calculator only handles molarity, which requires a volume input. If you know the density, you can convert mass of solution to volume, then use this calculator.

How do I make a 1 M solution of a compound?

Look up the molar mass of the compound (e.g., NaCl is 58.44 g/mol). Weigh out exactly that many grams (58.44 g for 1 L, or 5.844 g for 100 mL). Dissolve in about 80% of the final volume of water, stir until fully dissolved, then add water to reach the final volume mark. The final volume, not the water volume, determines the molarity.

Why does the calculator ask for molar mass instead of looking it up?

Molar mass depends on the exact compound, its hydration state, and isotopic composition. For example, NaCl is 58.44 g/mol, but KCl is 74.55 g/mol. There are thousands of possible compounds, so the calculator leaves the molar mass as an input. You can compute it from the periodic table by summing the atomic weights of all atoms in the formula.

Can I use this for diluting a concentrated acid like HCl?

Not directly. Concentrated HCl is a solution, not a solid, so you would need to know its concentration (often around 12 M) and use a dilution formula (C₁V₁ = C₂V₂) instead. This calculator is for preparing solutions from a weighed solid. For dilutions, you would enter the mass of solute already present, which is not how liquid reagents are measured.

Related

Formula used
in m | Mass of solute | g | 2.922 | 0
in mm | Molar mass | g/mol | 58.44 | 0.001
in v | Final solution volume | mL | 250 | 0.001
out c | Molarity | mol/L | m / mm / (v / 1000) | 4
out cmm | Concentration in millimolar | mM | c * 1000 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →