molecalculator

Moles & Molar Mass

Is RCF the Same as Xg? Centrifuge Units Explained

Calculator No. 01-2801 · Updated · Formula and assumptions shown below

Relative centrifugal force 1,006 ×g
Speed for target RCF
3,000 rpm
Result, rounded to a whole number
Rotor radius
10 cm
Set in the form below
Rotational speed
3000 rpm
Set in the form below
You enter
Rotor radius (cm), Rotational speed (rpm)
You get
Relative centrifugal force (×g), Speed for target RCF (rpm)
Rounding
0 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Yes. In centrifugation, “RCF” and “×g” refer to the same quantity: relative centrifugal force, expressed as a multiple of Earth’s gravitational acceleration. For example, 1,000 ×g means a relative centrifugal force of 1,000; it is not the same as 1,000 revolutions per minute (rpm).

Formula

Relative centrifugal force is calculated as RCF = 1.118 × 10−5 × r × rpm2. Here, RCF is the force relative to standard gravitational acceleration, written as a multiple of ×g; r is the distance in centimetres from the axis of rotation to the sample; and rpm is rotational speed in revolutions per minute. The factor 1.118 × 10−5 applies when radius is in centimetres and speed is in rpm.

The inverse calculation is rpm = √[RCF / (1.118 × 10−5 × r)]. In the calculator, enter the desired RCF in the field labelled Rotor radius only if using the second result is not possible; the calculator’s inputs calculate actual RCF from radius and speed, and the second output uses that RCF to show the equivalent speed at the entered radius. For a separately chosen target RCF, use the formula directly with that target value.

Worked Example

Using the default inputs, the rotor radius is 10 cm and rotational speed is 3,000 rpm:

  • RCF = 1.118 × 10−5 × 10 × (3,000)2
  • (3,000)2 = 9,000,000
  • RCF = 1.118 × 10−5 × 10 × 9,000,000 = 1,006.2 ×g, rounded to 1,006 ×g.

The displayed equivalent speed at this radius is 3,000 rpm, because it is derived from the same RCF and radius. The headline result is therefore about 1,006 ×g.

Assumptions

  • The radius is in centimetres and is measured from the rotational axis to the sample’s relevant position.
  • Rotational speed is steady and expressed in revolutions per minute.
  • The formula uses standard gravity, approximately 9.80665 m/s², as the reference for “g.”
  • This is a calculation aid, not a substitute for the rotor’s operating instructions or limits.

Why RCF and ×g Mean the Same Thing

RCF stands for relative centrifugal force. It describes the acceleration associated with rotation as a ratio to standard gravitational acceleration. Writing “1,000 ×g” is a compact way to say that the acceleration is 1,000 times the reference gravity. Some manuals and protocols label the setting “RCF,” while others write “×g”; in ordinary centrifuge instructions, those labels describe the same type of setting.

The quantity is technically an acceleration ratio, not a force measured in newtons. The “force” in the established name reflects the outward effect associated with rotation in the spinning frame. A sample experiences acceleration toward the rotor’s axis; the common centrifuge description of material being driven outward is a useful operational picture, but it does not change the mathematical definition.

Also, “g” here does not mean grams. A setting of 500 ×g is not a mass of 500 grams, nor is it a force of 500 newtons. It is a multiple of gravitational acceleration.

Why RPM Is Different

RPM counts how fast the rotor turns. RCF describes the resulting acceleration at a particular radius. Because the formula includes the square of rpm, changing rotational speed has a strong effect; because it also includes radius, the same rpm can produce different RCF values in different rotors.

For instance, doubling rpm at an unchanged radius makes RCF four times larger. Doubling the radius at unchanged rpm doubles RCF. As a result, a protocol specifying 1,000 ×g cannot reliably be followed by setting a particular rpm unless the rotor radius is known.

Two centrifuges running at 3,000 rpm may therefore expose samples to different RCFs if their effective radii differ. Conversely, different rpm settings may produce the same RCF when paired with different rotor radii. This is why protocols often specify RCF: it is more transferable between rotor sizes than rpm alone, though the sample position and rotor geometry still matter.

How to Convert Between RCF and RPM

To convert a required RCF to rpm, rearrange the standard formula and take the square root. You need the rotor radius in centimetres. For example, for a target of 1,000 ×g at a radius of 10 cm:

  • rpm = √[1,000 / (1.118 × 10−5 × 10)]
  • rpm ≈ √(8,944,544) ≈ 2,991 rpm.

This is an approximate conversion; use the centrifuge’s own RCF setting or validated rotor information when available. If the protocol gives rpm but you need RCF, use the direct formula, again with the correct radius. Do not mix radius units: entering millimetres as though they were centimetres creates a tenfold error in the calculated RCF.

Many instruments allow users to enter either rpm or RCF and apply a stored rotor profile. Check which quantity the display is showing, and verify that the selected rotor or radius matches the one actually installed.

Choosing the Correct Rotor Radius

Radius is measured from the axis of rotation to the sample position used by the stated formula. Rotor manuals may specify a maximum radius, a minimum radius, or a distance to the bottom or centre of a tube. These definitions can produce different RCF values, especially for swinging-bucket rotors, where the bucket changes position while spinning.

Use the radius definition supplied with the rotor or instrument, rather than estimating from the outside of the rotor. For a sample that occupies a substantial length of a tube, RCF varies along the sample: the material farther from the axis has greater acceleration. A protocol may define RCF at the sample’s maximum radius or another specified point, so follow that convention consistently.

When a protocol and instrument seem to disagree, check the stated rotor, radius convention, units, and whether the instrument reports RCF or rpm before changing settings. Never exceed the rotor’s rated speed or other operating limits.

Frequently Asked Questions

Is 1,000 RCF the same as 1,000 ×g?
Yes. In centrifuge settings, both mean a relative centrifugal force of 1,000 times standard gravity.

Is RCF the same as rpm?
No. RPM measures rotation speed; RCF is acceleration relative to gravity and depends on both rpm and rotor radius.

Does the same rpm give the same RCF on every centrifuge?
No. At the same rpm, a larger radius gives a larger RCF. Use the actual rotor radius to convert accurately.

What radius should I use to calculate RCF?
Use the radius and measurement convention specified for your rotor or protocol. It is generally measured from the axis to the relevant sample position, not simply the rotor’s outer edge.

Why does my centrifuge show a different rpm for the same RCF?
Different rotor radii require different speeds to achieve the same RCF. The instrument may also use a specific radius convention or rotor profile.

Can I use this formula for any centrifuge?
The relationship applies to centrifuges, but accurate results depend on correct radius and speed units. Follow the rotor’s instructions and rated limits; do not treat a calculated speed as authorization to exceed them.

Related

Formula used
in r | Rotor radius | cm | 10 | 0
in rpm | Rotational speed | rpm | 3000 | 0
out rcf | Relative centrifugal force | ×g | 1.118e-5 * r * rpm^2 | 0
out rpmreq | Speed for target RCF | rpm | sqrt(rcf / (1.118e-5 * r)) | 0

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →