molecalculator

Moles & Molar Mass

Kb to OH⁻ Concentration Calculator

Calculator No. 01-3797 · Updated · Formula and assumptions shown below

Hydroxide concentration [OH⁻] 0.001333 mol/L
pOH
2.8753
Result, rounded to 4 decimal places
Base dissociation constant Kb
0.000018
Set in the form below
Initial base concentration
0.1 mol/L
Set in the form below
You enter
Base dissociation constant Kb, Initial base concentration (mol/L)
You get
Hydroxide concentration [OH⁻] (mol/L), pOH
Rounding
4 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator estimates the hydroxide-ion concentration, [OH⁻], produced by a weak base in water from its base dissociation constant, Kb, and its initial concentration. Enter Kb and the base concentration in mol/L to get [OH⁻] in mol/L and the corresponding pOH; the result uses the usual weak-base equilibrium approximation.

Formula

For a weak base B reacting with water, B + H₂O ⇌ BH⁺ + OH⁻. The equilibrium expression is Kb = [BH⁺][OH⁻]/[B]. If the initial base concentration is C and x mol/L reacts, then [BH⁺] = x, [OH⁻] = x, and [B] = C − x. Substitution gives Kb = x²/(C − x). Solving this quadratic for the physically meaningful, nonnegative root gives:

[OH⁻] = x = (√(Kb² + 4KbC) − Kb) / 2

  • Kb is the base dissociation constant, dimensionless when expressed using standard-state activities; in dilute classroom calculations it is commonly treated as a concentration-based constant.
  • C is the initial analytical concentration of the weak base, in mol/L.
  • x is the equilibrium hydroxide concentration, in mol/L, under the stated model.

The calculator also reports pOH = −log₁₀([OH⁻]), where [OH⁻] is entered conceptually in mol/L relative to the 1 mol/L standard state. The Kb input cannot be negative, and the base concentration must be positive for this calculation to yield a defined pOH.

Worked Example

Using the defaults Kb = 1.8 × 10⁻⁵ and C = 0.1 mol/L:

  1. Calculate the discriminant: Kb² + 4KbC = (1.8 × 10⁻⁵)² + 4(1.8 × 10⁻⁵)(0.1) = 7.2324 × 10⁻⁶.
  2. Take its square root: √(7.2324 × 10⁻⁶) ≈ 0.002689312.
  3. Apply the positive-root formula: x = (0.002689312 − 0.000018) / 2 ≈ 0.001335656 mol/L.
  4. Rounded to the calculator’s four decimals: [OH⁻] = 0.0013 mol/L. Using the unrounded concentration, pOH = −log₁₀(0.001335656) ≈ 2.8743.

Assumptions

  • The solution is dilute enough that concentration is a useful approximation to activity.
  • The base establishes a single equilibrium represented by B + H₂O ⇌ BH⁺ + OH⁻.
  • The temperature is 25 °C for interpreting pOH and the familiar water-ion relationship.
  • The entered concentration is the initial concentration of the base in the final solution.
  • No other acids, bases, salts, or reactions materially affect the equilibrium.

When to Use the Kb Calculation

Use this calculation when a weak base is dissolved in water and you know its Kb and its starting concentration. Kb describes the base’s tendency to accept a proton from water: a larger Kb generally means a greater fraction reacts and produces hydroxide at the same starting concentration. It does not, by itself, state the hydroxide concentration; the initial concentration matters too.

The equilibrium model is appropriate for introductory equilibrium problems and many dilute solutions. It is not the right model for a strong base that dissociates essentially completely, for a mixture with several acid–base species, or when a common ion or other reaction changes the equilibrium substantially. In those cases, write the full set of relevant mass-balance, charge-balance, and equilibrium equations.

Approximation, pH, and Temperature

A familiar shortcut is [OH⁻] ≈ √(KbC). It comes from replacing C − x with C in Kb = x²/(C − x), which assumes x is small compared with C. A common check is that x/C should be about 5% or less; if it is appreciably larger, use the quadratic result rather than the shortcut. For the default example, the exact quadratic gives x/C ≈ 1.34%, so the shortcut is reasonable: √(1.8 × 10⁻⁵ × 0.1) ≈ 0.0013416 mol/L.

At 25 °C, pH + pOH = 14.00 is a useful dilute-solution convention, so the example corresponds to pH ≈ 14.00 − 2.8743 = 11.1257. This relation is temperature-dependent: water’s ionization constant changes with temperature, and concentrated solutions can have important activity effects. The displayed pOH comes directly from calculated [OH⁻]; do not interpret pH as universally equal to 14 minus pOH at every temperature or ionic strength.

Common Mistakes and Limits

  • Confusing Kb with concentration: Kb is an equilibrium constant, while C and [OH⁻] are concentrations. Do not enter a percentage or a pH value in place of Kb.
  • Using the initial concentration as the equilibrium concentration: some base becomes BH⁺. The equilibrium base amount is C − x, which is why the exact expression includes the quadratic term.
  • Applying the weak-base formula to a strong base: strong bases are treated by their stoichiometric dissociation and any relevant solution equilibria, not by a small Kb model.
  • Rounding too early: retain the unrounded hydroxide result when calculating pOH. The displayed concentration is rounded to four decimal places, which can look coarse for small values.
  • Ignoring other ions or reactions: salts, buffers, dissolved carbon dioxide, and multiple protonation states may alter the result. The single-equilibrium equation cannot account for them automatically.

Kb values depend on the identity of the base and specified conditions; use a reliable reference value for the relevant temperature and convention. For bench work, follow your lab method, the safety data sheet (SDS) and your supervisor.

Frequently Asked Questions

How do I calculate OH⁻ concentration from Kb?
For a weak base with initial concentration C, use [OH⁻] = (√(Kb² + 4KbC) − Kb)/2. The shortcut √(KbC) is suitable only when the amount reacting is small compared with C.

Can I find OH⁻ concentration from Kb alone?
No. You also need the initial base concentration and a suitable equilibrium model. The same Kb can yield different hydroxide concentrations at different starting concentrations.

What is the difference between Kb and pOH?
Kb describes the base’s equilibrium tendency to react with water. pOH is a logarithmic measure calculated from hydroxide concentration: pOH = −log₁₀([OH⁻]) when concentration is referenced to 1 mol/L.

Is [OH⁻] equal to √(KbC)?
That is an approximation, not the exact result. It assumes x is negligible beside C in the equilibrium denominator. Use the quadratic solution if the estimated x is more than a small fraction of C.

How do I get pH from Kb?
First calculate [OH⁻], then pOH = −log₁₀([OH⁻]). At 25 °C in a dilute aqueous solution, estimate pH as 14.00 − pOH; the relation changes with temperature and non-ideal solution conditions.

Related

Formula used
in kb | Base dissociation constant Kb | - | 1.8e-5 | 0
in cb | Initial base concentration | mol/L | 0.1 | 0
out oh | Hydroxide concentration [OH⁻] | mol/L | (sqrt(kb^2 + 4 * kb * cb) - kb) / 2 | 4
out poh | pOH | - | -log10(oh) | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →