molecalculator

Moles & Molar Mass

Archery Calculator: Arrow Trajectory and Impact Energy

Calculator No. 01-3798 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

An archery calculator estimates an arrow’s trajectory, flight time, and impact energy from inputs such as launch speed, distance, and arrow mass. These are mathematical estimates, not a substitute for sighting in a bow or practicing safely at a proper range.

Formula

This calculator uses a simplified projectile-motion model. It first finds flight time to a horizontal distance, then estimates vertical displacement and kinetic energy at that time. It assumes the arrow maintains its horizontal speed and that gravity is the only force changing its velocity.

  • Flight time: t = [2d sin(a) + √((2d sin(a))² + 2gd²/(v² cos²(a)))] / g.
  • Vertical displacement: y = v sin(a)t − ½gt². Positive y means the arrow is above its launch height; negative y means it is below.
  • Impact kinetic energy: E = ½(m/1000)[v² + (v sin(a) − gt)²]. Dividing mass in grams by 1000 converts it to kilograms.

Here, t is flight time in seconds, d is horizontal distance in metres, a is launch angle in degrees, v is launch speed in metres per second, g is gravitational acceleration (9.80665 m/s²), y is vertical displacement in metres, m is arrow mass in grams, and E is kinetic energy in joules. The angle must be from 0° to 45° for this calculator’s stated range.

Worked Example

Using the defaults—60 m/s, 30 m, 0°, and 25 g—first calculate flight time:

t = [0 + √(2 × 9.80665 × 30² / (60² × 1²))] / 9.80665
t = √(17651.97 / 3600) / 9.80665
t ≈ 2.205 s

Vertical displacement is:

y = 60 × 0 × 2.205 − 0.5 × 9.80665 × 2.205²
y ≈ −23.841 m

The negative result means the idealized arrow has fallen below its launch height by the time it reaches 30 m. Its vertical velocity is approximately 0 − 9.80665 × 2.205 = −21.623 m/s, while horizontal velocity remains 60 m/s in this model. Therefore:

E = 0.5 × (25 / 1000) × (60² + (−21.623)²)
E ≈ 52.10 J

The outputs, rounded to the calculator’s displayed precision, are 2.205 s, −23.841 m, and 52.10 J.

Assumptions

  • The arrow is treated as a point projectile in a uniform gravitational field with g = 9.80665 m/s².
  • Air resistance, wind, arrow flex, launch-device variation, and changes in speed are ignored.
  • The supplied speed is the arrow’s initial horizontal speed at launch; the mass is entered in grams.
  • Vertical displacement is measured relative to the release point, with no difference in target elevation.

What an Archery Calculator Can and Cannot Tell You

“Archery calculator” can refer to several different tools: an arrow-flight estimator, a kinetic-energy calculator, a sight-mark or trajectory aid, or a calculator for arrow specifications. This page combines a basic trajectory estimate with kinetic energy. It does not calculate a real bow’s sight settings or guarantee where an arrow will strike.

The model is useful for understanding broad relationships. For instance, greater launch speed reduces flight time over a fixed distance, which generally reduces the time gravity has to pull an arrow downward. A heavier arrow at the same speed has more kinetic energy because kinetic energy is proportional to mass. But actual arrows also lose speed to aerodynamic drag, and their behavior depends on design, tune, and environmental conditions.

At the default values, the predicted drop is so large that it clearly illustrates why the result should not be treated as a sight adjustment. The calculation assumes a level launch and target, ignores air drag, and does not account for aiming the bow above the horizontal. A real archer usually aims along a line that differs from the arrow’s initial flight direction.

Inputs and Reading the Results

  • Arrow speed: Use a speed measured for the particular bow-and-arrow setup if you have one. A value quoted for another setup may not represent your arrow in flight.
  • Distance: Enter the horizontal distance from launch to target in metres. This is not necessarily the sloping distance between points at different heights.
  • Launch angle: Enter the arrow’s initial direction relative to horizontal. Zero degrees represents a horizontal launch. The model does not tell you what angle to use when aiming.
  • Arrow mass: Enter total arrow mass in grams. Do not enter grains without conversion: 1 grain = 0.06479891 g.

Flight time is a model output, not a timing recommendation. Vertical displacement describes the arrow’s position relative to its starting height, not its height above the ground. Impact energy is the arrow’s calculated kinetic energy at the computed time. Because the model holds horizontal speed constant, its energy estimate will usually overstate energy after a real arrow has traveled through air.

Common Errors and Safety Limits

The most common input mistakes are mixing metres and feet, entering arrow mass in grains as if it were grams, and confusing horizontal distance with line-of-sight distance. For reference, 1 ft = 0.3048 m and 1 m = 100 cm. Keep units consistent, and do not interpret extra decimal places as evidence of real-world accuracy.

Trajectory calculations become especially unreliable at longer distances because aerodynamic drag and changing arrow speed matter increasingly. Wind, elevation difference, arrow orientation, and the bow’s actual launch behavior also affect a shot. For practical shooting, use a properly rated range, an appropriate backstop, and established local rules. Never use a calculation alone to select a target, determine a safe shooting lane, or judge whether a shot is safe; follow qualified instruction and the equipment maker’s safety guidance.

Frequently Asked Questions

What does an archery calculator calculate?
It depends on the tool. This one estimates idealized flight time, vertical displacement, and kinetic energy from speed, distance, launch angle, and arrow mass.

How do I calculate arrow kinetic energy?
Use E = ½mv², with mass in kilograms and speed in metres per second, to calculate energy at a specified speed. This calculator accounts for its model’s vertical velocity at the chosen distance, but assumes horizontal speed does not decline.

Does arrow drop equal the amount I should adjust my sight?
No. The calculated drop is relative to the launch direction in an ideal model. Sight adjustments depend on the bow’s actual trajectory, setup, range, and shooting form, so they must be established safely through practice.

Can I enter arrow weight in grains?
Not directly in the mass field, which expects grams. Convert grains to grams by multiplying by 0.06479891; for example, 400 grains is about 25.92 g.

Why does the calculator’s result differ from a real shot?
Real arrows slow down in air, and wind, launch angle, arrow setup, and elevation differences affect flight. This simplified calculation excludes drag and is best used to understand basic physics, not predict an exact impact point.

Related

Formula used
in v | Arrow speed | m/s | 60 | 0
in d | Horizontal distance | m | 30 | 0
in a | Launch angle above horizontal | degrees | 0 | 0 | 45
in m | Arrow mass | g | 25 | 0
out t | Flight time | s | (2 * d * sind(a) + sqrt((2 * d * sind(a))^2 + 2 * 9.80665 * d^2 / (v^2 * cosd(a)^2))) / 9.80665 | 3
out y | Vertical drop from launch height | m | v * sind(a) * t - 0.5 * 9.80665 * t^2 | 3
out e | Impact kinetic energy | J | 0.5 * (m / 1000) * (v^2 + (v * sind(a) - 9.80665 * t)^2) | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →