A Kp unit calculator converts an equilibrium constant expressed using gas pressures into the corresponding Kc value based on gas concentrations, or checks the units implied by a Kp expression. Enter Kp, temperature, and the reaction’s change in gaseous moles to calculate Kc; the conversion uses the ideal-gas relationship and is valid only when the reaction equation and pressure convention are clear.
Formula
For ideal gases, the relationship is Kp = Kc(RT)Δn, so the calculator uses Kc = Kp / (RT)Δn. Here Kp is the equilibrium constant written with partial pressures relative to a standard pressure, Kc is the corresponding concentration-based constant, R is the gas constant 0.0820574 L·atm/(mol·K), T is absolute temperature in kelvins, and Δn equals the sum of stoichiometric coefficients of gaseous products minus the sum for gaseous reactants. Solids and pure liquids are omitted from both equilibrium expressions.
The calculator’s Kp input is treated as dimensionless, as it is when each partial pressure is divided by a pressure standard state. Older textbook treatments may assign pressure units to Kp and concentration units to Kc; under that convention, the numerical conversion depends on the specified units and standard-state convention. Do not mix those conventions silently.
Worked Example
Use the calculator defaults: Kp = 1, T = 298.15 K, and Δn = −1. A negative Δn means the balanced reaction has one fewer mole of gaseous products than gaseous reactants.
- RT = 0.0820574 L·atm/(mol·K) × 298.15 K = 24.46540361 L·atm/mol.
- (RT)Δn = (24.46540361)−1 = 0.04087324.
- Kc = 1 / 0.04087324 = 24.4654, reported to four decimal places.
The corresponding conversion factor is 0.0409 to four decimal places. The displayed Kc is dimensionless under the standard-state convention described above.
Assumptions
- Gas behavior is ideal, so partial pressure and concentration are related by p = cRT.
- Temperature is entered in kelvins, not Celsius.
- Kp and Kc use consistent standard-state definitions; the calculator treats them as dimensionless.
- Δn is calculated from the balanced chemical equation and includes gases only.
- Pure solids and liquids do not appear in the equilibrium expression.
How to Find Δn
First balance the reaction. Add the coefficients of all gaseous products, then subtract the coefficients of all gaseous reactants. Include only species marked as gases; a coefficient of one is still counted. For example, for a hypothetical reaction A(g) ⇌ 2B(g), Δn = 2 − 1 = 1. For A(g) + B(g) ⇌ C(g), Δn = 1 − 2 = −1. If the gaseous totals match, Δn is zero and Kp = Kc in the ideal-gas relationship, regardless of temperature.
Do not count a dissolved substance as a gas just because it participates in an equilibrium. Aqueous species belong in a concentration-based expression, but not in the gaseous mole-count difference used for this conversion. Likewise, omit pure liquids and solids. If a reaction includes multiple gaseous species, use each balanced coefficient exactly as written.
What the Result Means
Kp and Kc describe the same equilibrium in different ways: Kp uses gas partial pressures, while Kc uses molar concentrations. The conversion does not predict the equilibrium composition or change the equilibrium position. It only translates the numerical constant between representations, given temperature and the reaction’s Δn.
When Δn is positive, the power of RT is positive, so Kc = Kp/(RT)Δn. When Δn is negative, dividing by a negative power is equivalent to multiplying by the corresponding positive power. This is why Kc can be greater than Kp for the default example. A larger numerical value does not by itself mean a reaction is more favorable: equilibrium constants are meaningful only with their defined expression, units or standard states, and temperature.
Common Errors and Limits
- Using Celsius: Convert temperature to kelvins before applying the formula. For example, 25 °C equals 298.15 K; entering 25 as kelvins gives a different, incorrect result.
- Reversing Δn: Use gaseous products minus gaseous reactants. Reversing the subtraction changes the conversion factor to its reciprocal.
- Using an unbalanced equation: Δn depends on stoichiometric coefficients, so an unbalanced equation cannot provide the correct exponent.
- Counting non-gases: Include only gaseous species, not aqueous compounds, solids, or pure liquids.
- Mixing pressure units or standards: The expression here uses R in L·atm/(mol·K) and the dimensionless standard-state form. A calculation based on bar, pascals, or dimensional constants requires a consistent treatment of standard pressure.
The conversion assumes ideal gases. At high pressures or under conditions where gases depart substantially from ideal behavior, fugacity is a more accurate thermodynamic quantity than partial pressure, and this simple conversion may not be adequate. Also, equilibrium constants depend on temperature; a Kp measured at one temperature should not be converted using a different temperature unless the constant itself is first adjusted using suitable thermodynamic data.
This calculator is for study and lab-planning arithmetic, not a substitute for a specified thermodynamic model. For bench work, follow your lab method, the safety data sheet (SDS) and your supervisor.
Frequently Asked Questions
What is the formula for converting Kp to Kc?
Kc = Kp/(RT)Δn for ideal gases, where Δn is gaseous product coefficients minus gaseous reactant coefficients. Use the same equilibrium and standard-state convention for both constants.
What does Δn mean in a Kp-to-Kc calculation?
It is the net change in gaseous stoichiometric moles: total gas coefficients on the product side minus total gas coefficients on the reactant side. Ignore aqueous, solid, and liquid species.
Does Kp equal Kc when Δn is zero?
Yes, the ideal-gas relationship gives Kp = Kc when Δn = 0, because (RT)0 equals 1.
Can I use temperature in Celsius?
No. Enter kelvins. Convert Celsius to kelvins by adding 273.15; for example, 25 °C is 298.15 K.
Why do some textbooks give units for Kp or Kc?
Some use dimensional equilibrium expressions, while modern thermodynamic definitions commonly divide activities or pressures by standard states so the constants are dimensionless. The numerical value and unit presentation must follow one convention consistently.
Related
Formula used
in kp | Kp (dimensionless, pressure-standard-state form) | - | 1 | 0 in t | Temperature | K | 298.15 | 0.001 in dn | Change in gaseous moles, Δn | mol | -1 | - out kc | Kc (dimensionless, concentration-standard-state form) | - | kp / (0.0820574 * t)^dn | 4 out factor | (RT)^Δn conversion factor | (L·atm/mol)^Δn | (0.0820574 * t)^dn | 4
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Skip Calculator for Soil: What It Can and Can’t Do7.500 m³
- USD to KPW Calculator: Convert Dollars to North Korean Won90,000.00 KPW
- OK Calculator on TV on the Radio? Meaning Explained
- Pension Calculator KP: Estimate Your Pension Benefits
- Neonatal Kp Calculator: What It Means80.0000 mmol/mmol
- Newton to kp Converter Calculator and Formula1.0000 kp