molecalculator

Moles & Molar Mass

kPa to PSIg Calculator: Convert Pressure

Calculator No. 01-11935 · Updated · Formula and assumptions shown below

Pressure (gauge) 14.50 PSIg
Absolute pressure
29.20 PSIa
= (Pressure (gauge) ÷ 6.894757) + 14.6959
Absolute pressure
201.3 kPa (absolute)
= Pressure (gauge) + 101.325
Pressure (gauge)
100 kPa
Set in the form below
You enter
Pressure (gauge) (kPa)
You get
Pressure (gauge) (PSIg), Absolute pressure (PSIa), Absolute pressure (kPa (absolute))
Rounding
2 dp · 1 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator converts a pressure value in kilopascals (kPa) to pounds per square inch gauge (PSIg). You enter the gauge pressure in kPa, and you get the equivalent in PSIg, plus the absolute pressure in both units. The conversion uses the exact factor 1 PSI = 6.894757 kPa.

Formula

The conversion from kilopascals to pounds per square inch gauge is:

PSIg = kPa ÷ 6.894757

Where:

  • kPa = pressure in kilopascals (gauge), the input value
  • PSIg = pressure in pounds per square inch gauge (the output)
  • 6.894757 = exact conversion factor: 1 PSI = 6.894757 kPa

For absolute pressure, add the standard atmospheric pressure (101.325 kPa = 14.6959 PSI) to the gauge value.

Worked Example

Using the default input of 100 kPa (gauge):

  1. Divide by 6.894757: 100 ÷ 6.894757 = 14.5038 PSIg
  2. Round to 2 decimals: 14.50 PSIg
  3. Absolute pressure in PSIa: 14.5038 + 14.6959 = 29.1997 → 29.20 PSIa
  4. Absolute pressure in kPa: 100 + 101.325 = 201.3 kPa absolute

So 100 kPa gauge equals 14.50 PSIg, which is about one atmosphere above vacuum.

Assumptions

  • Standard atmospheric pressure is 101.325 kPa (14.6959 PSI) at sea level.
  • The input is a gauge pressure, meaning it is measured relative to ambient atmospheric pressure.
  • The conversion factor is exact and does not depend on temperature or fluid type.

Why Gauge vs. Absolute Matters

Pressure readings come in two flavors: gauge and absolute. A tire gauge reads 0 when open to the atmosphere, so it shows pressure above atmospheric. Absolute pressure includes the 101.325 kPa (14.7 PSI) that the atmosphere already exerts. Many industrial gauges display PSIg, while vacuum systems and gas law calculations (like the ideal gas law PV = nRT) require absolute pressure. If you mix them up, your calculations can be off by about 14.7 PSI (101 kPa) — a huge error in most applications.

For example, a scuba tank filled to 3000 PSIg actually contains 3014.7 PSIa. When you use the ideal gas law to estimate how long the air lasts, you must use the absolute value. This calculator shows both so you can avoid that mistake.

How to Use the Conversion in Practice

Here are the common situations where you will need this conversion:

  • Tire pressure: Many cars specify pressure in kPa (e.g., 220 kPa), while US gauges read PSI. Divide by 6.894757 to get about 32 PSI.
  • HVAC and refrigeration: Manifold gauges often read PSIg, but system specifications may be in kPa.
  • Industrial pneumatics: Air compressors are rated in both units; converting helps compare equipment.
  • Engineering reports: International standards (ISO) use kPa, while US-based projects often use PSI.

To convert manually, remember: 1 kPa ≈ 0.145 PSI. So 100 kPa ≈ 14.5 PSI. For a quick mental estimate, divide kPa by 7 to get PSI (the exact factor is 6.894757, so 7 is close enough for rough checks).

Common Mistakes and Misconceptions

One frequent error is forgetting that PSIg and PSI are not the same if the context implies absolute. A pressure of 0 PSIg is 14.7 PSIa, not zero. Another mistake is using the reverse conversion (multiplying by 6.894757 instead of dividing). Check your result: 1 kPa is about 0.145 PSI, so any kPa number should be smaller when expressed in PSI. If your PSI value is larger than your kPa value, you divided when you should have multiplied.

A related misconception is that kPa and PSI are interchangeable in gas law equations. They are not — the ideal gas constant R has different values depending on the pressure unit (8.314 J/(mol·K) with kPa, 0.08206 L·atm/(mol·K) with atm, and 10.73 (ft·lbf)/(lb·mol·°R) with PSF). Always convert to the unit required by your formula.

When to Use PSIg vs. PSIa

Choose the scale based on what you are measuring:

  • Use PSIg for most mechanical gauges, tire pressure, and hydraulic systems, because they compare to ambient air.
  • Use PSIa for gas law calculations, vacuum work, and any situation where you need the total pressure from absolute zero.
  • When a spec says just “PSI,” check the context — in the US, it usually means gauge, but in scientific literature it often means absolute.

For vacuum pressures, gauge values are negative (e.g., -30 inHg), but kPa gauge can also be negative. This calculator accepts any non-negative kPa input; for vacuum, enter a small positive value or use absolute pressure instead.

Frequently Asked Questions

Q: How many PSI is 100 kPa?
A: 100 kPa equals 14.50 PSI (gauge). Divide 100 by 6.894757 to get 14.5038, rounded to 14.50. This is roughly the standard atmospheric pressure at sea level.

Q: What is the difference between PSI and PSIg?
A: PSI is a general term for pounds per square inch, but it is ambiguous. PSIg explicitly means gauge pressure (relative to atmosphere), while PSIa means absolute pressure (relative to vacuum). A tire gauge reads PSIg; a barometer reads PSIa. The difference is 14.6959 PSI at sea level.

Q: Why do some countries use kPa instead of PSI?
A: kPa is the SI unit for pressure, used in most of the world and in scientific work. The US still commonly uses PSI for everyday applications like tire pressure and industrial gauges. Converting between them is necessary for international communication and engineering.

Q: Can I convert kPa to PSIg without a calculator?
A: Yes, for a rough estimate: divide kPa by 7 to get PSI. For example, 200 kPa ÷ 7 ≈ 28.6 PSI (exact is 29.0). For precise work, use a calculator or the exact factor 6.894757.

Q: Does temperature affect the kPa to PSI conversion?
A: No, the conversion factor is a unit definition, not a physical law. However, the actual pressure of a gas changes with temperature (Boyle’s and Charles’s laws), so if you are measuring a real gas, the pressure reading will vary with temperature, but the conversion from one unit to another does not.

Q: Is 1 kPa equal to 1 PSI?
A: No. 1 kPa is about 0.145 PSI, and 1 PSI is about 6.895 kPa. They are not close; a 100 kPa reading is about 14.5 PSI. Always use the conversion factor, not a 1:1 assumption.

Related

Formula used
in kpa | Pressure (gauge) | kPa | 100 | 0
out psig | Pressure (gauge) | PSIg | kpa / 6.894757 | 2
out psia | Absolute pressure | PSIa | (kpa / 6.894757) + 14.6959 | 2
out kpaa | Absolute pressure | kPa (absolute) | kpa + 101.325 | 1

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →